Sinker Guy, After searching high and low (No pun intended) for a decent surf rig, your video and rig board saved the day. I spent about $10.00 and made two in less than 30 minutes. Thanks again for sharing your love of fishing.
Hello from Atlantic Beach. Thanks for the instructional. I have a double drop rig board I built 2 years ago, and it works well but yours is more compact, and it has dropper length options, so I am gonna give it try. Thank you again!
Perfect instructions took all of 30 minutes to make once I found tools in hubbys’s shed! For novice folks like me I put tape on drill bit so I knew when I was at 1/2 inch. So excited my beads and pill floats will be in a few days!! Thanks
I made a bastardized version roughly inspired by this. 2 clips, 3 short dowels and a tall screw for spools (some of mine have an I.D. of under 1/2"). Only 3 dowels as I just picked a single size; up until now, they were pretty random and usually shorter than intended. Now *much* quicker and more consistent. Thanks!
Chip, I've seen these boards demonstrated at surf seminars in the past but this is the first time with measurements. I had a math teacher maybe 60 years ago say, "if you can put numbers on it you don't understand it". It shows that you are a teacher at heart. Thanks.
Just moved to East cost of Florida from Montana. Getting started with Surf Fishing and I have begun to build your Rig Board, Only question is what is the post at 18 1/2 inches used for. I watched your "How I tie my double dropper loop rigs" video and did not see you use that 2 inch post. Thanks for doing the videos, They are a big help...
Just finished up my rig board...had all the stuff to build it right in the garage. It’s a miracle that I didn’t have to make 3 trips to the hardware store like I do with every other project I start 😂
Awesome instructional video. I ran into a fisherman on the Atlantic Beach today who turned me on to your videos. I don't have much line fishing experience as all my fishing has been spearfishing for many years. He also showed me some of the sinkers you make too. I'll be interested in getting some of them soon. Thank you for sharing.
Great video. Very in detail. I am about to order the drill tool that you use to put the float and linecthrough and your spike likecweights as well. Thank you for showing me how to do this. I will try to make it. How do I make the drop loop smaller I don't like the access of line? I would like no more than 2.5 inches on each drop loop. Any suggestions.
Thanks for putting this out. Like I've said in one of my previous comments, just got back in to fishing and went to B&M and grab a couple of rigs and really didn't like where the weight sat. But i get caught a couple keeper drum.
Within a couple of months, I’ll be headed your way with some techniques from yourself and Slot City Fishing to test my luck out on those waters for the first time. Adding surf fishing to my fishing career 😂
Yes it is a few before this one. Surf Fishing Florida how to tie the BEST surf fishing rig, (DOUBLE DROPER RIG). Jacksonville Florida ruclips.net/video/zetVxfgZdGQ/видео.html
Watched the whole video. How did you not include showing how to tie rigs with it? I was thinking to my self, "this looks cool", can't wait to see what it can do.
I had already did a video on how to use it and thought it would be redundant to show it again. Search back on my channel on how to make double drop rigs
Just found your video and subscribed to your channel. Built the rig board over the weekend but am wondering what the middle peg at 18 1/2 inches is used for. Also, thanks for the prompt response and delivery of my Surf Fishing bundle from The Sinker Guy!!
Someone sponsor this legend!
You’re giving away your secrets! Love the passion you have for the sport. Thanks for being such a great teacher!!
Sinker Guy, After searching high and low (No pun intended) for a decent surf rig, your video and rig board saved the day. I spent about $10.00 and made two in less than 30 minutes. Thanks again for sharing your love of fishing.
That is exactly why we do it!!! Thanks for the props!
@thesinkerguy Good day sir. Can you please give me the measurements for the pompano rig tying board ?
I’ve looked at every rig board building video I can find. THIS is the best! Thank you.
Perry Hodges thank you for the kind words! Super happy I was able to help!
Hello from Atlantic Beach. Thanks for the instructional. I have a double drop rig board I built 2 years ago, and it works well but yours is more compact, and it has dropper length options, so I am gonna give it try. Thank you again!
This video should have millions of views, this is unbelievably helpful! Thank you Chip!
Excellent! Simple! This will be on my table soon!
Fish Gum I love I could help!!!!! Let me know if you have any questions!
Perfect instructions took all of 30 minutes to make once I found tools in hubbys’s shed! For novice folks like me I put tape on drill bit so I knew when I was at 1/2 inch. So excited my beads and pill floats will be in a few days!! Thanks
That is super awesome to hear! Keep me updated!
Just one word for this rig board.... Phenomenal!!
Thank you...
I made a bastardized version roughly inspired by this. 2 clips, 3 short dowels and a tall screw for spools (some of mine have an I.D. of under 1/2"). Only 3 dowels as I just picked a single size; up until now, they were pretty random and usually shorter than intended. Now *much* quicker and more consistent. Thanks!
Thanks for these instructions. I’m making one this weekend. I’m also going to make a measuring board and will share with you when it’s done.
Chip, I've seen these boards demonstrated at surf seminars in the past but this is the first time with measurements. I had a math teacher maybe 60 years ago say, "if you can put numbers on it you don't understand it". It shows that you are a teacher at heart. Thanks.
Ok just found the video of you making the rig. Thanks!!!
Slot City linked to this video. Wow, great way to make good, consistent rigs. Thanks for posting it.
Just moved to East cost of Florida from Montana. Getting started with Surf Fishing and I have begun to build your Rig Board, Only question is what is the post at 18 1/2 inches used for. I watched your "How I tie my double dropper loop rigs" video and did not see you use that 2 inch post. Thanks for doing the videos, They are a big help...
Genius! Thank you for making your jig board open source!
I’ll be building this board tomorrow....thanks for sharing the info!!
Just finished up my rig board...had all the stuff to build it right in the garage. It’s a miracle that I didn’t have to make 3 trips to the hardware store like I do with every other project I start 😂
Great job, very easy to follow.
I bought everything to make the board! Thanks Sir!
Manny Ramos enjoy the process of making your board
Thanks for sharing this info... I tie my own rigs but this will help with better spacing...
What size are the eye screws
Great job! Can you show us how to assemble the rigs on this board? Thank you.
Thanks again for sharing! I look forward to building one and getting some consistency to my rig sizes.
Michael S you are so very welcome!
Made my own rig after watching your video. Works like a charm. Thanks for sharing.
Awesome instructional video. I ran into a fisherman on the Atlantic Beach today who turned me on to your videos. I don't have much line fishing experience as all my fishing has been spearfishing for many years. He also showed me some of the sinkers you make too. I'll be interested in getting some of them soon. Thank you for sharing.
Then you for watching and commenting! I think you might have met Eddie! Good luck out there and subscribe fishing pole give away very soon!
Thank you sir!! Slot City sent me. Subscribed
Thank you so much, more great content coming soon.
Using a brad point bit will eliminate (practically) the need to "deburr" the drilled holes.
Thanks for sharing!!!! I want to make one now but I have to find your video and seeing how it’s used 😂
I’m super excited to build this thank you.
noah bargas you are very welcome and glad we could help! Subscribe up top lot of more things coming up!
Excellent sir! Thanks for a no nonsense easy to follow video.
Great video. Very in detail. I am about to order the drill tool that you use to put the float and linecthrough and your spike likecweights as well. Thank you for showing me how to do this. I will try to make it. How do I make the drop loop smaller I don't like the access of line? I would like no more than 2.5 inches on each drop loop. Any suggestions.
I would just look at how I made my rig board and you can make a 2 inch drop instead of the 4 inch I make.
Wow that's a nice board
Who gave this a thumbs down? Thanks for the video!
Thanks for sharing. I’m going to make one tomorrow.
Thanks Chip🎣🎣 Tight Lines!!!
Bobby Coville absolutely keep em tight!
Do you have a video on how you use the board to make rigs
This video explains how to use the peg board: ruclips.net/video/X5sLQH_N3BM/видео.html
Great tool, thank you
You're welcome!
Thanks for putting this out. Like I've said in one of my previous comments, just got back in to fishing and went to B&M and grab a couple of rigs and really didn't like where the weight sat. But i get caught a couple keeper drum.
Datil Man thank you so much! Keep after it and subscribe above some more good videos coming that will help!
@@thesinkerguy sweet thanks🤙
What size drill bit did you use to drill the holes for the pegs?
Thank you, good instructional information.
Glad it was helpful!
Dude....the quality of instruction in your videos is from another planet!!! Thank you very much for teaching us!!! You are def a legend!!
Legit broseph! Let me get dat board.
Within a couple of months, I’ll be headed your way with some techniques from yourself and Slot City Fishing to test my luck out on those waters for the first time. Adding surf fishing to my fishing career 😂
Love this board. I'm going to redo mine like rhis.
Thank you man for sharing.
Albatross315 you are very welcome! Subscribe more great info is coming!
Great video and I just subbed. Slot City send me!
is there a videio showing how to use this board and what rigs one can tie with it?
Yes it is a few before this one.
Surf Fishing Florida how to tie the BEST surf fishing rig, (DOUBLE DROPER RIG). Jacksonville Florida
ruclips.net/video/zetVxfgZdGQ/видео.html
Awesome!! Do you have a video
Do you have a video on how to make a rig using the board?
nice job
I normally use 4oz to 6 oz weights, would you recommend a 50# test so my weights don’t break off
10# test for each ounce. #50 test -5oz but will do fine with a 6oz
What size drill bit for 2 and 5 inch line pegs? Thx
Awesome! Thank you!
Watched the whole video. How did you not include showing how to tie rigs with it? I was thinking to my self, "this looks cool", can't wait to see what it can do.
I had already did a video on how to use it and thought it would be redundant to show it again. Search back on my channel on how to make double drop rigs
@@thesinkerguy OK Thanks. I didn't know. I'll look for it.
Gonna get husband to make This template, I’ve tied my rigs for years, using my teeth and toes to help hold the fluorocarbon!🤣🤣🤣
This will help for sure! Look into our rig tying tool also.
Just found your video and subscribed to your channel. Built the rig board over the weekend but am wondering what the middle peg at 18 1/2 inches is used for. Also, thanks for the prompt response and delivery of my Surf Fishing bundle from The Sinker Guy!!
You can make bigger loops by using the other peg at 18 1/2 inches
And you are so very welcome!!!!
Hi how do you use this board thanks
I need to buy rig board from you (Sinkerguy)
I have a few ready to make! I will get on it this week
@@thesinkerguy Great !!! I'm really looking forward to purchased the board just let me know when and how...also like you to sign the board (Sinkerguy)
You in the Jacksonville Fl area
@@thesinkerguy I'm in Biloxi MS
How thick is the wood that you used?
2x8
@@thesinkerguy thanks! Gonna get some wood and make this beauty.
How do you use it?
There is another video on how to use it!
do you sell the Rig Board ? if so how much .
If you are local to Jackson, Yes!
Rig board kit I do sell also!
They are $15! They come will all part you just need the board, drill and 2 bits.
@@thesinkerguy i am in Houston TX would like to buy one, dont see it on the web site
steve miller As of right now order the casting cannon and I will switch it on my end. You can leave a note also!
This video would have been better if you had showed us how to tie a rig‼️
Go watch the video on how to tie using the rig board.
🐰😜😂