Dear Doctor, First of all, thanks for your comment and we are delighted that you appreciate XP-endo Shaper. FKG does not have a specific recommendation regarding the type of irrigation to be used with our instruments, this is specific to each dentist. However, it seems that a mix between both is the most common nowadays. Thereby, during instrumentation canals should be irrigated using copious amounts of the NaOCl solution. Once the shaping procedure is completed, canals can be thoroughly rinsed using EDTA (and for an optimal result, the use of XP-endo Finisher is recommended). I hope that we will have been able to answer your request, if necessary do not hesitate to contact us again. Best regards, FKG Dentaire TEAM
Hello ! The XP-endo Rise is conceived for continuous rotation indeed. If you feel more comfortable with reciprocating systems, we would suggest for your to try the R-Motion :) -Your FKG Team
Dear Dr. Sarah Alkhateeb. Thanks for you request. As mentioned in our official Instructions For Use, for both XP-endo Shaper and XP-endo Finisher you don't need to fix the working length 0.5 mm short. If you need more details, please visit the IFU section on our Website : www.fkg.ch/media-center/instructions-use. Best regards, FKG Dentaire TEAM
Thank you so much , I read all the details but also I have small question about this file is the prepration by this file always reach size 30 core diameter with 0.04 taper ? Thank you very much and sorry for more question because I prepare lecture in details about this file and I will explain all the details to the dentists
Dear Dr. Sarah Alkhateeb. Once you've used the XP-endo Shaper for the 10 additional strokes over the entire length of the canal, the final apical dimension should be at least 30/.04. If 30/.04 is desired and the gutta percha point does not fit, you can work the XP-S for an additional 5-10 strokes. We hope this information will help you prepare your lecture. Best regards, FKG Dentaire TEAM.
@@fkgdentaire Thank you so much for your help in preparing my lecture about this file I put your video inside my lecture because all the details found in this video it really nice video I post my lecture about this file on my youtube account and on my slide share account
Dear Sir or Madam, The minimum recommended operating speed for the XP-endo Shaper is 800rpm, and its optimum speed is 1,000rpm. If you use it at a speed below minimum 800rpm, unfortunately the instrument will not be use at its full capacity and therefore will not reach its full efficiency. Today you can easily find endodontic motors reaching speeds of 800rpm or even higher. For example our new Universal Rooter has this feature. If you would like more information on the Rooter Universal, please do not hesitate to consult our website by the following link: fkg.ch/products/endodontics/motor-apex-locator/rooter-universal or to contact your local FKG dealer: fkg.ch/dealer Best regards, FKG Dentaire TEAM
Thanks for these wonderful instrument 🙏
Q/what type of irrigation best to use with these instrument ? Nacl of edita gel ?
Dear Doctor,
First of all, thanks for your comment and we are delighted that you appreciate XP-endo Shaper.
FKG does not have a specific recommendation regarding the type of irrigation to be used with our instruments, this is specific to each dentist.
However, it seems that a mix between both is the most common nowadays. Thereby, during instrumentation canals should be irrigated using copious amounts of the NaOCl solution. Once the shaping procedure is completed, canals can be thoroughly rinsed using EDTA (and for an optimal result, the use of XP-endo Finisher is recommended).
I hope that we will have been able to answer your request, if necessary do not hesitate to contact us again.
Best regards,
FKG Dentaire TEAM
This game has the worst graphics ever the only
Hello, I'd Like to ask do you use clockwise rotation only with this instrument?
Hello ! The XP-endo Rise is conceived for continuous rotation indeed. If you feel more comfortable with reciprocating systems, we would suggest for your to try the R-Motion :)
-Your FKG Team
What obturation method is recommended with this system?
Available in pakistan?
I ask in finisher file also -0.5mm from the working length or not
Dear Dr. Sarah Alkhateeb. Thanks for you request. As mentioned in our official Instructions For Use, for both XP-endo Shaper and XP-endo Finisher you don't need to fix the working length 0.5 mm short. If you need more details, please visit the IFU section on our Website : www.fkg.ch/media-center/instructions-use. Best regards, FKG Dentaire TEAM
Thank you so much , I read all the details but also I have small question about this file is the prepration by this file always reach size 30 core diameter with 0.04 taper ? Thank you very much and sorry for more question because I prepare lecture in details about this file and I will explain all the details to the dentists
Dear Dr. Sarah Alkhateeb. Once you've used the XP-endo Shaper for the 10 additional strokes over the entire length of the canal, the final apical dimension should be at least 30/.04. If 30/.04 is desired and the gutta percha point does not fit, you can work the XP-S for an additional 5-10 strokes. We hope this information will help you prepare your lecture. Best regards, FKG Dentaire TEAM.
@@fkgdentaire Thank you so much for your help in preparing my lecture about this file
I put your video inside my lecture because all the details found in this video it really nice video
I post my lecture about this file on my youtube account and on my slide share account
@@fkgdentaire ruclips.net/video/lSFc6APX3ZM/видео.html
What does XP stands for?
XP stands for expending, since the file will reach its true size in the root canal with the patient's temperature :) -Your FKG Team
Hello, i have endomotor nsk, max speed is 450 rps, can i use the xp shaper with this speed? Thank you
Dear Sir or Madam,
The minimum recommended operating speed for the XP-endo Shaper is 800rpm, and its optimum speed is 1,000rpm.
If you use it at a speed below minimum 800rpm, unfortunately the instrument will not be use at its full capacity and therefore will not reach its full efficiency.
Today you can easily find endodontic motors reaching speeds of 800rpm or even higher. For example our new Universal Rooter has this feature.
If you would like more information on the Rooter Universal, please do not hesitate to consult our website by the following link: fkg.ch/products/endodontics/motor-apex-locator/rooter-universal
or to contact your local FKG dealer: fkg.ch/dealer
Best regards,
FKG Dentaire TEAM
tried but I couldn't get this file