You need two engine gateways YDEG-04 with BRP adapter cables. Alternatively, you can rewire YDEG-04 engine connectors as pinout differs of BRP diagnostics connector. Then you need to configure YDEGs. For that, you need to make a text file named YDEG.TXT with the lines: # most of brp engines have baud rate 500 kbps while YDEG default baud rate is 250. Only old BRP engines (produced near 2005) have 250 kbps. ENGINE_CAN_SPEED=500 # this turns on BRP protocol support: BRP_ROTAX=ON # Also you need to set up engine instances. Set this for port engine: ENGINE_0=0 ENGINE_1=OFF BATTERY_0=0 BATTERY_1=OFF FUEL_0=0,PORT FUEL_1=OFF # Settings for starboard engine: ENGINE_0=OFF ENGINE_1=0 BATTERY_0=OFF BATTERY_1=0 FUEL_0=OFF FUEL_1=0,PORT Then copy this file to microSD card formatted in FAT32 and install to YDEG. It should blink green-green-green once - this means file is read and accepted. Then reboot YDEG to apply baud rate settings and check if you have green-green indication when engine and NMEA2000 are ON. If so, connection is successful. It is recommended to update YDEG-04 firmware with 1.40 version. Refer to this link: www.yachtd.com/news/#07092023
@@nekokoneko3856 I have the same problem as you. One red light and one green light. Garmin can recognize YGED-4 but cannot receive engine data. I am a foreigner. There is no chat software for you. You can only ask here
@@钱网 First RED flash = no connection to engine bus. Need to check if you got +12 Volt DC power on engine's 6-pin female diagnostic connector. Turn engine ignition ON. You should get approx. + 12 Volts DC on socket 5 ( Red + Black wire , V+ ) in respect to socket 3 ( Black wire, GND ). If no voltage, seek for blown fuse in the fusebox ( Red + Black wire has a dedicated fuse ).
No engine data received. Please, kindly, send several good quality photos showing how is YDEG-04 connected to the engine exactly to our technical support - www.yachtd.com/support/ Make sure to take good quality photos, with all connectors, wires and their positions clearly visible. -- Alex K, Yacht Devices engineer --
I’m getting the same results when I plugged mine in. Did you get your problem fixed. I followed the manual on setting up for a BRP engine and still can’t get any data on my Raymarine axiom 9. Any help would be Appreciated.
@@csrammanram4457 Please, turn engine ON and NMEA 2000 backbone ON and confirm the LED indication you got on YDEG-04 unit ? YDEG-04 should produce a sequence of two consecutive LED flashes, which sequence is observed ?
What is solution for twin engine , sea doo 230 challenger ????
You need two engine gateways YDEG-04 with BRP adapter cables. Alternatively, you can rewire YDEG-04 engine connectors as pinout differs of BRP diagnostics connector. Then you need to configure YDEGs. For that, you need to make a text file named YDEG.TXT with the lines:
# most of brp engines have baud rate 500 kbps while YDEG default baud rate is 250. Only old BRP engines (produced near 2005) have 250 kbps.
ENGINE_CAN_SPEED=500
# this turns on BRP protocol support:
BRP_ROTAX=ON
# Also you need to set up engine instances. Set this for port engine:
ENGINE_0=0
ENGINE_1=OFF
BATTERY_0=0
BATTERY_1=OFF
FUEL_0=0,PORT
FUEL_1=OFF
# Settings for starboard engine:
ENGINE_0=OFF
ENGINE_1=0
BATTERY_0=OFF
BATTERY_1=0
FUEL_0=OFF
FUEL_1=0,PORT
Then copy this file to microSD card formatted in FAT32 and install to YDEG. It should blink green-green-green once - this means file is read and accepted. Then reboot YDEG to apply baud rate settings and check if you have green-green indication when engine and NMEA2000 are ON. If so, connection is successful.
It is recommended to update YDEG-04 firmware with 1.40 version. Refer to this link: www.yachtd.com/news/#07092023
Possible to install on a seadoo jet ski 2021 gti se 170?
yes, all modern BRP engines are supported by YDEG-04
@@nekokoneko3856 Is there a guide available for this?
@@baysidejetskihire1118 yes, please, check the YDEG-04 manual, section IV.2 Connection to BRP Rotax Engines
@@nekokoneko3856
I have the same problem as you. One red light and one green light. Garmin can recognize YGED-4 but cannot receive engine data. I am a foreigner. There is no chat software for you. You can only ask here
@@钱网 First RED flash = no connection to engine bus. Need to check if you got +12 Volt DC power on engine's 6-pin female diagnostic connector. Turn engine ignition ON. You should get approx. + 12 Volts DC on socket 5 ( Red + Black wire , V+ ) in respect to socket 3 ( Black wire, GND ). If no voltage, seek for blown fuse in the fusebox ( Red + Black wire has a dedicated fuse ).
Getting a red green led light what could be wrong
No engine data received. Please, kindly, send several good quality photos showing how is YDEG-04 connected to the engine exactly to our technical support - www.yachtd.com/support/
Make sure to take good quality photos, with all connectors, wires and their positions clearly visible.
-- Alex K, Yacht Devices engineer --
@@nekokoneko3856 can you give me all part needed for a 2022 sea-doo switch 170 with a garmin 72sv and I will purchase thank you!
You need our YDEG-04 gateway + extra "BRP adaptor cable" available as YDEG-04 accessory.
I’m getting the same results when I plugged mine in. Did you get your problem fixed. I followed the manual on setting up for a BRP engine and still can’t get any data on my Raymarine axiom 9. Any help would be Appreciated.
@@csrammanram4457 Please, turn engine ON and NMEA 2000 backbone ON and confirm the LED indication you got on YDEG-04 unit ? YDEG-04 should produce a sequence of two consecutive LED flashes, which sequence is observed ?