EXTREME RC 4X4 Sabertooth 2x12 ESC Install Into Kyosho Blizzard
HTML-код
- Опубликовано: 10 сен 2024
- In this video I go through the main steps you need to take to install a sabertooth 2x12 esc into your Kyosho Blizzard. This esc is a much higher quality than the stock ones and is in my opinion a good upgrade. Thanks for watching!
Very good job and excellent explanations . At 9:11 you got a little faster, I think he can not wait to go back to the snow ahahah... :- Great video .. :-)
sator rotas yes it definitely caught me off guard. Thank you for the compliments once again!
@@ExtremeRC4x4 I put the sabertooth in my skidsteer build done the same thing lol!!! Thanks for the review they are a great product
Travis Rc lol I hope you were able to durability test it from the fall!
@@ExtremeRC4x4 it keep on going after it fell off the work bench lol
@@ExtremeRC4x4 I've got to get a blizzard been wanting one for quiet some time enjoy yours much ?
I have a question. I have this motor driver and it works pretty well. Its driving two drill motors in a track vehicle. My question is when I do a zero point turn, it will turn well when spinning counter clockwise but when I try to do it do it in the clockwise direction it struggles, can anyone help me with that?
amigo que motores usaste en tu proyecto?
Keep going, well done.
MrFlashman10 Thanks a lot!
Hello Ethan, I just installed the saber tooth esc and the traxxas 380 motors. I used the stock radio. I can’t get the plow to work and my controls are all backwards. What used to be forward and backward is not anymore. How do I fix this.
Michael Flannery have you made sure that all the switches on the esc are set correctly? Another thing to check is if everything is plugged into the receiver properly.
What do you set your switches at??
This is interesting fore sure..The one i see on Ebay dodent look exatly the same, have some ribbs on the side(cooling?),..i see Amazone dosen`t ship to Norway...any sugestion where i can by, dosen`t seem like someone in Norway sell it..Great explaining video
jan erik skogmo mod-56 yes some of the other models have more cooling fins. Not sure about where they could be purchased in Norway. Thanks for watching!
how do you make it go back and forth that I can't ...
Alessandro Sgarbi I’d be open to trying to help but it is incredibly difficult to problem solve with such little information.
@@ExtremeRC4x4 Hi I wrote you an email privately
Alessandro Sgarbi I have looked it over but due to your very specific build I can’t help. I would contact sabertooth as I’m sure they are more capable to helping with their product
@@ExtremeRC4x4 OK thank you very much
What motors did you use on your build?
I have just been running the stock ones. I have had the best luck with them especially because I don’t want anything too fast.
sabertooth works with hoverboard motor?
Gianluca Virgenti I’m not sure, you’d probably be better off contacting someone at sabertooth or even some online forums. Thanks for watching!
What Chanel’s did you put what on?
Briason Whitlock channel 2 of the ESC is on channel 4 of the radio. Channel 1 of the esc is on channel 3 of the radio. Then the other two are just for my plow and snow groomer
Ethan Boening thank you.
Briason Whitlock glad to help!
Hi, Nice video. Can you run lipo battery with Sabertoot ?
McFly Thank you! Yes, I run a 2s 5000mah Lipo. Just make sure the ESC is on lipo mode so the battery doesn’t get drained too far.
@@ExtremeRC4x4 ok thanks :)
Here is my first video with Sabertooth and 540 motors runing on my dx4c on 3s lipo , Thanks again for your video's ruclips.net/video/8lb-9cOBSEk/видео.html
Which servo you are using
Rahul Ghosh I believe at this point it is either the stock servo or the servo that came with the rear tiller. Thanks for watching!
@@ExtremeRC4x4 I don't want to buy whole setup I need knowledge about a servo that can be fit in a arm to lift 500g......length of arm 20cm
Rahul Ghosh I couldn’t tell you the exact servo that you need for you’re situation but definitely something higher output.
Sadly you showed nothing, nor did you explain anthing. You did more than explain. I will be making my own because EVERYONE Of these videos are terrible about showing detail on hookup or changing switches as to what they do.
RC Hobbyist Extreme what more would you like to see? The guide to the switches was showed at the 5:10 mark. I tried to show my wiring setup between battery, esc, and motors. I went through my entire setup on camera and I also used other people’s videos as a way to educate myself before purchasing or installing. Although I believe that I along with many others have made quality videos covering the esc maybe you can do better yourself.
What battery are you using?
RC Hobbyist Extreme a 2s 5000 mah Lipo
@@ExtremeRC4x4 Awesome thanks! I am in the process of modifying everything.
You are pretty uncomplimentary here . Ethan is trying very hard and your comments don't help. Keep up the great work Ethan!