Speeduino Ocelot
HTML-код
- Опубликовано: 5 фев 2025
- ==Ocelot Tuner Studio Settings==
Board type is UA4C
Onboard MAP sensor is an mpxh6400a
Onboard Barometric sensor is an kp234 and is on pin A7
==Ocelot Jumper Settings==
first jump your primary/secondary jumpers to either 'tsc' (vr) or 'direct' (hall)
-Secondary trigger config is closest to the edge of the board
-Primary trigger config is closest to the VR conditioner headers
next, if using hall, you likely need to jump the 'pull up resistor' for the given primary/secondary trigger
==Pinout for ocelot==
github.com/tur...
==Drivers for ocelot==
www.silabs.com...
==3d printed case==
www.printables...
Ocelot is a Speeduino based ECU that is being sold by WMTronics.com. This is not a sponsored video, I purchased this ECU with my own money because I wanted to try it out. This video is a boiled down reaction/how to video for operating this ECU.
The Speeduino community is filled with great people who have helped me figure out how to at least get my jeep running, and hopefully ill be an actual tuner soon because of the community help. I simply hope I can give something back to the community with this video.
==My Socials==
Discord Server: discord.gg/Ev6E6Mh6AH
Twitch: twitch.tv/sharkfac3lives
Instagram: sharkfac3lives
Very cool! Hope to see more in the future!
i can 110% guarantee there will be more, redoing stream setup and trying to get better recording of the builds. You can see in this video that i had some really awkward camera angles (some footage really hurt the eyes but its all i had LOL)
I'm right here with you. Just assembled my ocelot board now I'm trying to just find any info on it.
Dont hesitate to reach out to me with any questions!
YEESSS
Now she just needs a proper wire harness instead of this hack job LOL
Do you know if it’s possible to connect the ocelot with a Honda obd1 wiring harness, and if so how would I do that?
It should be possible, I am not sure how much of the old harness you would be able to get working 110% with ocelot.
Your honda ECU has all the wires coming in/out of it, wire by wire you have to match that to the pin on ocelot. here is the pin mapping: github.com/turboedge/SpeedyBoards/blob/master/OCELOT/DOC/Ocelot%20Connector%20Mapping.pdf
For example: pin 48 is injector 1. You would have to figure out which pin coming into your ECU is the injector 1 pin, then either splice in a new wire, or cut the old wire and have it go to the ocelot ecu
Yew!
she moved some logs the other day too!
Betty is the best
Betty is such a beauty
I just got my ocelot as well. Having a rough time figuring out where the jumpers have to be placed on the board for 12v Cam & Crank Hall Sensors for an LS engine. Any help would be awesome.
on the board, on the opposite side of the usb plug, where it says 'tsc|direct', those are your jumpers to configure for hall sensor.
so the 6 pins:
. . .
. . .
and you need to jump them to direct
. ---
. ---
this is a horrid explanation. you can find me on discord and instagram as well. im in the speeduino discord server, feel free to @sharkfac3 there :D
Good day sir I want to buy the ocelot for my car mitsubishi mirage 1999. Could you help with the set up. Like a video on the settings please. I would be truly greatful
I wish this was an easy one for me to help you on, I do not know much about Mitsubishi engines.
You would need to know if the trigger setup on your engine is compatible with speeduino. I would suggest giving this one a read: mirageforum.com/forum/showthread.php/6400-Megasquirt-for-the-Mirage
that is for megasquirt, but megasquirt and speeduino are similar
what was the issue you were having with the board?
primary and secondary trigger labels got switched lol