- Видео 65
- Просмотров 11 688
Leo's Small Engines & Stuff
Добавлен 21 апр 2020
I love cars half life 2 and portal, built a voron 2.4 love working on small engines bikes and go karts
(learned how to weld yipe!!!)
(learned how to weld yipe!!!)
Modified Walmart car speaker & Homemade amp play "Ali-A Intro"
Modified Walmart car speaker & Homemade amp play "Ali-A Intro"
Просмотров: 7
Видео
Homemade Speaker/Subwoofer & Homemade Amp plays Bass I Love You Ft: Modified Walmart Car Speaker
Просмотров 142 часа назад
Yes I know the enclosure is small its what I had on hand. The previous speaker in this enclosure blew up from the V2 Amp. This speaker is a modified 10$ dual cone 3.5" car speaker from Walmart. The amp uses a IRF540 Mosfet and is an inefficient class A amplifier.
Homemade Speaker and Amp playing "Bass I Love You"
Просмотров 3749 часов назад
Homemade Speaker and Amp playing "Bass I Love You"
How to change the tires on your car! (First video on a CAR!!!)
Просмотров 5221 час назад
Tell me if I did anything wrong ;D
Shindaiwa 360 swapped Razor MX350
Просмотров 10914 дней назад
Had an old Shindaiwa 360 with a shot clutch and shot oil pump. Also had an MX350 frame. Anything is possible with a welder :D
Focusing a mini 5" CRT PART 2
Просмотров 22 месяца назад
UPDATE: Tube is dead. was getting grid to work when tube shut off.
Powering on a 5 inch CRT from a portable TV! PART 1
Просмотров 192 месяца назад
This was pulled from a 5.5" battery powered crt tv. Analog is no longer in use for tv so it is usless! But i can pull the CRT out and use it in a project!
Mini 3" Cathode Ray Tube showcase.
Просмотров 33 месяца назад
This tube was taken from a slide in module for a server rack oscilloscope.
Fixing the connecting rod bearings on my go kart! Part 1
Просмотров 1173 месяца назад
Fixing the connecting rod bearings on my go kart! Part 1
3D Printed gas engine ROTARY!!! (Part 1)
Просмотров 174 месяца назад
3D Printed gas engine ROTARY!!! (Part 1)
Bear stealing apples from apple tree! (new property)
Просмотров 754 месяца назад
Bear stealing apples from apple tree! (new property)
The 2 stroke does not like being contained (poulan wild thing engine)
Просмотров 5165 месяцев назад
The 2 stroke does not like being contained (poulan wild thing engine)
Old go kart motor locks up! Running without oil for 10 minutes straight!!!! (Full video)
Просмотров 1776 месяцев назад
Old go kart motor locks up! Running without oil for 10 minutes straight!!!! (Full video)
Not much Bass
i know (proper subwoofer on the way)
@@leossmallengines even so that speaker should be moving that homemade amp is inputting 0 bass
@@LostMySpark15 i am testing right now with a car speaker and there is very much bass. Might upload other video if you like.
@@leossmallengines it weird because that speker has some excursion power unless the speaker wattage is too much for the amp
@@LostMySpark15 maybe, the new speaker is being tested on a v2 of that amp. It could be better.
RUclips. STOP. TURNING. MY. COMMENTS. OFF!!!
You need a longer cable so it doesn’t get too tight and pull the throttle from turning the bars could get real sketchy 😂 Btw that thing is sick and you know what your doing, keep it up 👍
it has a manual clutch i can just engage the clutch. And yes I do need a longer cable!
The sense of speed on that driving footage is incredible!
File that tip to a V shape and open up the gap as wide as you can and then test. If it sputters close it up some. Or get a double iridium plug and open that up but dont cut of the Iridium. Its from outer space🤣 You can mill the head for more compression and port and valve job it. My leaf blower sounds like a Harley😎
the engine on this is kapoot currently. a bit late! (dont buy an engine for 30$ from an old man)
@@leossmallengines Fix it, thats how I started. While your in there port it and raise the compression. Make it sound like a harley.....😅
yooo your audio quality is good bro keep posting
with a good editor he would make great videos
RUclips STOP TURNING OFF MY FUCKING COMMENTS!!!!!!!
agreed
This kid is on here cussing up a storm and I get banned from commenting because I used bad words... Not only is he swearing this is completely dangerous....
and how is using a lathe dangerous? If you seriously think using a lathe is dangerous you should watch the latest video of me powering a crt with 1200v
Learn the machine little man you are going to hurt yourself... die.... or crash the machine. Lol.
super cool! im currently trying to make a homemade engine with my 3d priner!
Thanks! I actually watched that! And i am currently making my own few engines (not 3d printed, milled.), may upload a video about them soon.
@@leossmallengines are you using a mill that you have? I want to make an aluminum piston for my engine, but with no milling machine, it would be kind of difficult.
@@ProjectLMZ yes, and i have a lathe as well. If you want i can mill/turn you out an aluminum piston if you send me some plans! Oh and sorry for the long reply i was sleeping.
Bear not stealing apples, Creator God owns that tree and God told Bear to go get food.
Bears don't steal as they do not recognize ownership.
That is the biggest apple tree I ever saw, or a very small bear...Hard to tell which one...big tree or small bear or a little of both...I have a RUclips channel all about my two properties in the woods...Friday I saw a fox but did not get a video of it...Nice video.
small bear and also its super overgrown here its hard to tell but its just multiple trees
tell me in the comments if you want a full explanation / tutorial on controlling old crt's "easily" and "without touching 30,000 volts"!
You should build yourself a little cabin or tree house out there somewhere...That would make for some good RUclips videos too.
ive always wanted to but my parents always said we dont have space. Now we do!
Is this a chainsaw engine love the content man
yup!
look at the idle jet (also refered as the low end jet)
crank seals i think
Reminds me of my young self! I still love playing with like that! Keep it up, you’ll never stop learning.
btw. With music, usually RUclips will detect it, and then you can get your video removed, so be carefull (own experience) and turn up your mic and the music down a little bit
Well a third maybee, with STRG+shift+I you can enable AI, the it will empty Most of the time without crashing, you can also change the top speeds for that somehow...
"Ignore Safety" -Leo, 2024
Keep it up. You have lots of potential.
Minor inconvenience
damn broski thats cool i dropped a sub for u i might do content like this one day👍👍👍
Oh man, this brings me back. In the early days of RUclips, like in 2007-2009, myself and a whole bunch of others did this kind of thing all the time on here. Back then it was more like a close knit community, since RUclips was still small, and there were not many folks posting small engine content yet. Thanks for the memories!
Ok. But why?
shitty old engine that never runs right decided to end it
Subscribed, liked. We did this dumb stuff in highschool, good old times. See if you can get your hands on a snowmobile engine, about the same weight but huge power cos 2 stroke. And usually cheap.
bro why tf is this blowing up this isnt even the full video (its on my channel)
520 ain’t blowing up really
@@MaldonadoMoto my average views is 25 😭
@@leossmallengines put oil in next time, kid
@@LiquidSnakeSSJ4 some context: that motor is a motor i converted from a vertical shaft. it developed severe valve clatter and was just generaly shit (i just did it for fun using a free lawnmower i got). after every single bolt stripped from my dumbass trying to fix it it just sat in my garage for months. here i drained the oil and decided to kill it for "science". on attempt 1 of killing it i just revved it like crazy and it didnt do anything (my camera died mid filming and i didn't notice 🥶) so this was attempt 2 where i just drained the oil and let it do its high ass idle
@@LiquidSnakeSSJ4you really thought you cooked with this comment lmao. Shiver me timbers😭
You should check your gas tank for trash and clean the tank filter, replace the inline filter if there is one then clean your carb out, checking the mian jet and especially the pilot jet it makes the idle work. Don't get carb cleaner on anything rubber.
thx!!! already cleaned the 2 jets but i should still clean the rest and clean the tank (it looks horrible when there is no gas in it it looks like its textured on the bottom but its supposed to be smooth 😳) also my air filter is a bit too small for this engine
You seem to have carburetor issues and not spark
yeah im just trying side gapping for fun :D
You should be able to unbolt your pull start and turn it then bolt it back up to where you can pull back from the go kart instead of forwards...I have always had to do that with the Predator 212 cc engines.
Nice! it does seem like the 3 holes line up in either orientation, plus i did that on the old engine that i converted from a mower engine. Gotta try that!
I like the brake...I did a scrub brake once with a pedal and a rod/ linkage, but not with a hand brake...I thought the hand brakes just dragged on the ground when you pull up...I think that was why they called it a knuckle buster...I may have to copy your brake set up on my next budget build...
Yeah there's a reason they call it the knuckle buster, when you pull up the tire can catch on the brake and pull it up quickly, if you have a good design that doesn't rotate against the wheel and just pushes against it this doesn't happen :D
yoo keep up the good work kid! 🎉
That was pretty cool, but maybe a little dangerous too.
i love danger
I can see the kart has a gas engine now
its a completly new frame the old one is cracked in half and on the wall :D (new one is metal!!!!!!)
the fact that this guy just does this is crazy keep up the good work PS: I know u
are u max
credit to you for not getting your foot killed on the front beam
I thought one of the front wheels would have broke first.
the front left wheel did fall off before but i wasn't filming 😅
same
That car ended up being as free as a bird.
GOOD LORD! I love this. You earned a new sub. I'll be looking forward to more of your content. Would you want to do a BeamNG collab in the future (on RUclips or Twitch as a livestream?)
Depends what but for some messing around in beamp, sure!
alternative title: car edging at 144p
bro is edging us
Yes, it was a free bird
💀
why is this blowing up 😩
Cause we love you
@@Meerkat000😳
1700bph, nice!
yessir
why is this blowing up 😳
Nice
Hey, I watched your video again..I think the reason it doesn't run right is because your gas tank is not vented. The cap looks like a radiator cap which would hold pressure. On a gas tank I think you need a vent. You could try running it with the cap off and see if it runs better.
I had that problem before but i removed the o-ring from the cap and it fixed it. Also i found out that blocking off the breather causes the oil to seep past the piston rings faster from the pressure and it fouled the plugs! (gonna have to rebuild the breather :( )
Wow You did that video like right after I asked to see what the go kart looks like. Thank you for showing it. Did you make that purple part to turn the carburetor 90 degrees like when you turned the engine 90 degrees? You know V-shaft to H-shaft. I would like to see how you did the steering too. I think the next go kart I make I am going to try and do with no welding.
Yes the purple part is to turn the carb (its 3d printed) :D
sorry for shaky hands its cold in garage 🥶