Видео

Yes fact! Just got done tying up some myself due to the lack of water..... cant float anything! Thanks for watching and commenting!! Good Luck & Good Fishin!!

@@malcolmbutler801 Thank you my friend!

Thanks, got lucky on that 1

Thats what I was thinking or a Channel Kitty.

@@raystomberski4480 Thank-you. It's always so much fun, and I love to show people you that Dont need a 20+ Foot boat for Lake Erie, to get out far enough to get on them. My Raft is 12 ft by 4ft, and Powered by a 2.3 HP Honda. And make for some many fun filled days it's paid for itself 50 times over.

What are you using for bait

@@rudolphvarshine1606 Shiners

@@raystomberski4480 Its a Modded...Saturn FR380. Here is a link to where I got it, and I did tons Of Home Made Fishing Mods. Even have Salmon and Steelhead Deep water Downriggers on occasion. www.boatstogo.com/12.5-large-heavy-duty-fishing-raft-fr380xl.asp

@@raystomberski4480 Also did a Complete "Show and Tell" video of the boat on my YT page.

@@bobowhite11 show and tell you tube videos

@@raystomberski4480 ruclips.net/video/t4uIBWOLDD8/видео.htmlfeature=shared

@@raystomberski4480 Thank-you

Pm me I'll give you all the info you will need. Bait Gere kayak launching spot, and fishing grounds my man! Just got back, and slammed over 30 total fish in about 3 hrs!

@@navychief8425 8 to11 Ft deep. About 1/4 mile off shore.

@@bobowhite11 Thank you sir. I am on the east basin of Lake Erie out of Buffalo

@@navychief8425 we have it super shallow here less than 40 ft deep in the western basin. The area I fish Avgs 4 to 6 ft. Good Luck, and good fishing!

Thank you, started following you also!

@@bobowhite11 thank you

Around 7 to 8mph

TikTok will be the death of all amateur cinema…

Third year and not 1 issue so far.

the wind chill will get to your hands that aren't covered.

For sure it's easier to handle the fish

It was 40 degrees that morning, these still allow my hand to keep the heat in, but still allow me to be able to tie on knots.

That's a fact,,, it was freezing that day. Most Anglers were calling it early as it was slow fishing. But The gloves made me stay and I ended up with a full limit that day. I just had to move and find them down river a mile or so.

​@@alexfamie5255For sure a fact!!! I have even Liped Walleye as long as I have the "Thicker Mill" gloves for Mechanics, but only when needed. 😂😅😊

4K?? Sorry you did not like the quality of the vid. I will try to do better.

Thank you for the compliment. Third year and have had not 1 issue. From skinny water to Lake Erie she has had many miles under her.

Short shaft. Works like a charm, no need for the long shaft.

Fantastic!! She motors, and tracks straight while rowing also!

I use 8 footers. But here is the formula to get the exact length correct the 1st time! Measure the distance between BOTH oar sockets. Divide this # by 2, and then add 2 to this number. This Sum will tell you your ''Inboard Loom Length''. Take this Inboard Loom Length and Multiply it by 25, then Divide this by 7. The Sum will be the ...''Appropriate Oar length'' in inches for your Loom Length.

@@bobowhite11 thanks! I used a similar calculation but came up w 7' and it seemed too short because the raft sits high in the water. I came up w 7.9' and that is more like it 👍

I started with PVC Pipe. Heating a 4 foot piece up with a heat gun. Then simply "hand bending" it, while placing it on the boat. After bending it I made the entire aft frame and rack out of PVC. Once I was happy I took it all apart and measured everything including the ANGLE OF THE BEND. IT IS 23.5 DEGREES, AND CAN VERY FROM 22 TO 25 AND WORK FINE. .

FYI, the plans and Parts list are up under the "Community Tab" on my page!

I used a Pipe Bender from Harbor Freight... here www.harborfreight.com/12-ton-hydraulic-pipe-bender-32888.html

The corre t angle for the bend is 22 .5 degrees! I mis-printed 13 in a comment, while Meaning to round it to 23 degrees!

FYI, the plans and Parts list are up under the "Community Tab" on my page!

I will get one up. I had a day in the water with Mans best friend, and she was loving every minute of it.

FYI, the plans and Parts list are up under the "Community Tab" on my page!

FYI, the plans and Parts list are up under the "Community Tab" on my page!

ruclips.net/video/bTFwQ4mBO40/видео.htmlfeature=shared

It Rows and Tracks great, using a Honda 2.3 HP. I have run Class 2 Rapids and Had it out on Lake Erie and Lake Michigan. Fantastic value and great size .

FYI, the plans and Parts list are up under the "Community Tab" on my page!

ruclips.net/video/bTFwQ4mBO40/видео.htmlfeature=shared

@@bobowhite11 Hey buddy, I appreciate the response. The boat is freaking awesome. Just watched the new vid with the drone too. Over the winter I ended up getting a 12ft Bris white water raft. I DIY’d a frame and based a lot of what I did off your video. I still have some things to add including a motor mount and anchor mount/ system. I searched the web intensively to find someone likeminded DIYing a raft and I can 100% say your video is the only one that I found to be exactly what I was looking for. I’m a subscriber now! Best of luck this year on the water. I’m in Pennsylvania, otherwise I’d say we should get the rafts out together sometime! Lol

@@JordanFrank-y7j Awesome! Sweet boats and IM sure you will love it. Get out there and get wet!

No Sir this is the Fish Weir on the Little Manistee River is Michigan.