Видео

Yeah i do have plans for the engine, not a swap initially but i want to investigate other ideas i have first. Brakes deffo, once bodywork is in good condition certainly discs on the front. I kinda want to keep car as close to stock as possible, but who knows!

Thankyou very much 👍 George is from my neck of the woods 😁

Nein danke, es funktioniert wunderbar. Warum kaufen, wenn ich Scheiße machen kann?

I am pleased your enjoying the vids. Im back over xmas time so hopefully more content to come

I'll keep that in mind for my next project. In fact i already have my eye on a 2 stroke

They*

Fantastic pleased to hear and thankyou very much. Keep us updated on your progress and share your knowledge, as will help others keep their 126 Maluch on the road 👍

Good tip 👍 But im not going to try this again. Next time mechanic. Thanks.

@@desilva68 I understand why you say this,but my comment is more for the people who view your video of this nightmare

Thanks 👍

Its a Clarke pro 90 mig welder

Do you not have an engine at all ? If you do there is a serial number near the head. If you google it it should tell you which one you have.

I think i only had the copper rings. one on each cylinder.

Aftermarket from ebay

Defo get a mechanic. This had my pants down 😫

Yeah I’ve seen a couple of vids saying the nut can sheer or break so better off with a pro doing it also been told to go for like for like replacement but they can vary in price from £45-£150 🫣

@@davidwalker4800 £54.99 it cost me from ebay. It works so not bad. I think the main problem was the nut is made from stainless steel and its soft. So most of the threads stripped inside exhaust when trying to get it off. I did actually think if this does'nt work then i will cut exhaust on either side and weld some sort of connector to slide it back on. Then some exhaust clamps to hold in place. But so far its worked great.

To be honest I haven't tried it for a while. Do you suspect it's not very good by any chance? Im hoping to be using it again in the next couple of months for a new project im working on, so ill see then.

@@desilva68 No idea really, just curious if you have had any problems as it will be Chinese made but Stamos may have required additional quality control or design mods. Some Chinese based welders get a poor rep, others seem ok.

Hi, yes I bought a secondhand blue module for about £50 that did the trick. I suspected the one in car was faulty as a screw was missing from mounting plate and the heat sink separated as i took it off the car. Best £50 spent I would say!

@@desilva68 awesome, good to know. They're hard to find but I'm getting something out of Poland.

I got mine from Facebook marketplace when in Poland. Set my settings to Wroclaw and there is a place where he has loads and posts. Maybe he only posts inside Poland but i got it while I was there. Good luck hope it works 👍

Thanks for the advice I have a friend in Poland who sources hard to find parts. He found a unit and will hopefully get it early next week. Not sure if from the same seller as yours

18" wheels with 225 tires. Front spacer is 15mm rear spacer 10mm. Hope this helps.

Ha ha cheers man👍

Not a good comment and tough. You make a video.

@@desilva68 take my words as good advice, not criticisisum.

You didnt give me any advice! You just criticised my video🥴 but thanks for watchin 👍

I agree. Way too loud😝

Thanks for the honesty! I'll work on my video skills while you work on publishing your own content!

@@desilva68 no worries it's not about the criticism it's the journey that matters bud, still a nice bike.

It was tough but should come. Maybe it had been painted and just a tight fit. You could try heat if not WD40. but do the heat before you do the wd, otherwise you may loose your eyebrows😂. Keep going and let me know how it goes.

Hasnt been for MOT yet. But plan is to put original back on and maybe leave it, its too loud🤣

Very modest. its a bit like shy bairns get nowt.... i think?

Cheers man. Yeah it is a real pain especially when im only over here a few times in the year. I always feel like im rushing about to get simple things done.

Who needs quiet when you can have the Mad Max vibe, right? Thanks for checking out my other content! There will be more updates on this bike soon. Currently trying out a headlight cowl painted in the gulf colours and a new GPS speedo also in gulf colours. Maybe too much but we will soon see how it all looks. Thanks @Brian07900

Glad you enjoyed it!

Couldn't agree more!👍

Hi, not 100% sure as its been a while but i think they were a 17mm head, so probably 10mm thread.

You and me both!😝 Thanks for watching.

Hey, thanks for tuning in! I'm pleased that you found it entertaining! Stay tuned for more fun videos! Or check out my other vids.

Haha, thanks for the love! Stay tuned for more exciting content.

Thanks for the well-wishes! If you ever do find something positive to say, feel free to drop by. Until then, I'll be cruising on the highway of constructive criticism. Safe travels to you too

They have been absolutely perfect. No issues at all. Well worth the money.

yeah thanks. Its a different world here sometimes you can just do stuff. I'll pass on the compliment. Never rode before and she didnt stall...must have something to do with the high idle 😂

Thankyou very much young sir. I have ladies on my next video so you need to watch that one 😃

@@desilva68 Cheers ! I'll watch out for it then : )

Thanks for sharing and your probably correct👍

Ha ha yes they are hard to come by these days😂