- Видео 34
- Просмотров 144 031
Steel Dog
Добавлен 9 июл 2018
Steel Dog - FIBERGLASS FLAT TIES for Western Aluminum Forms
Russ Talpey of Talpey Construction talks about using Steel Dog - Fiberglass Ties - with his Western, Aluminum forms.
The Steel Dog Fiberglass Tie is a drop-in replacement for a steel flat tie for aluminum forms.
This job featured a massive exposed concrete wall at the front of the house, and the architect/homeowner were concerned about steel ties bleeding rust on the wall.
Steel Dog's Fiberglass Ties offered a seamless solution to eliminate rust concerns without complicating the pour.
Ties are ground or broken off flush with the wall and are virtually invisible.
Video produced and edited by Mint Drone Shots
www.mintdroneshots.com/
The Steel Dog Fiberglass Tie is a drop-in replacement for a steel flat tie for aluminum forms.
This job featured a massive exposed concrete wall at the front of the house, and the architect/homeowner were concerned about steel ties bleeding rust on the wall.
Steel Dog's Fiberglass Ties offered a seamless solution to eliminate rust concerns without complicating the pour.
Ties are ground or broken off flush with the wall and are virtually invisible.
Video produced and edited by Mint Drone Shots
www.mintdroneshots.com/
Просмотров: 153
Видео
Steel Dog Booth Tour - World of Concrete 2022
Просмотров 3,5 тыс.2 года назад
A quick tour of the Steel Dog Booth at WOC 2022. Visit our website for product details! steel-dog.com/
Scaffold Brackets
Просмотров 4,6 тыс.3 года назад
Steel Dog® Scaffold Brackets have keyhole slots to attach to the hex head shoulder bolts of Steel Dog® panels or compatible 1-1/8” form panels. Each Scaffold Bracket attaches to two bolts to safely carry the load. Heavy duty, welded 1/4” steel and angle iron construction. Keyhole slots provide a strong and secure means of attachment to form panel shoulder bolts. For more info check out our webs...
Top Waler Bracket / Waler with Wedge
Просмотров 6 тыс.3 года назад
A Rugged, Versatile Clamp for 1-1/8” Forming Using the TWC-450 is the best way to secure a 2x4 to the top of your form panels for perfectly straight walls. Sets securely with a quick blow to the wedge, and strips just as easily. Like all Steel Dog hardware, the TWC is designed and manufactured with the user in mind. Heavy-gauge steel, rounded corners, no sharp edges the TWC is rugged and made t...
SideBar Extension Bracket
Просмотров 1,3 тыс.3 года назад
A simple way to extend your forms This versatile clip from Steel Dog® allows you to easily add extra height or secure job-built fillers to modular steel frame forms. Available in two sizes - for 1-1/2” lumber and 3/4” plywood. The clip holds itself in place when lumber is installed, or for additional security a wedge bolt can be installed. For more info check out our website steel-dog.com/produ...
Form Oil Sprayer - Engine Start Up
Просмотров 2763 года назад
How to start the engine on the Steel Dog® S-1000 series Form Oil Sprayer For more info check out our website steel-dog.com/products/oil-sprayer
Form Oil Sprayer - How to Clean the Filter
Просмотров 1943 года назад
How to clean the pump filter on a Steel Dog® S-1000 series Form Oil Sprayer. For more info check out our website: www.steel-dog.com/products/oil-sprayer
Strongback Clamp
Просмотров 2,4 тыс.3 года назад
Stack your 1-1/18” forms with confidence using these heavy-duty clamps. The SBC-4 accepts a single vertical 2x4 provide security while stacking, while the SBC-8 accepts an additional horizontal 2x4 to ensure true alignment of panels. For more information check out our website steel-dog.com/sbc-strongback-clamp?rq=strongback
Stacking Clips
Просмотров 2,2 тыс.3 года назад
The Panel Clip and the Stacking Clip are thin, strong, steel clips for joining 1-1/8” plywood panels to other 1-1/8” stock (HC-112) or to 1-1/2” lumber (HC-150.) Either clip gives you a quick, inexpensive way to pour a slightly higher wall with your existing form panels. For more info check out our website: steel-dog.com/hc-stacking-clip?rq=hc
Angle Corner Clips
Просмотров 1,3 тыс.3 года назад
Steel Dog® Angle Corner Clips are a fast, inexpensive alternative to full-height, metal outside corners. Available in 22.5°, 30°, and 45° versions, these clips slip tightly onto the end of the panel bar, converting a pair of standard filler panels into a corner in seconds. Reduce the number of heavy, expensive, and maintenance-prone full-height corners in your inventory. For more information ch...
BT - Tie Breaker
Просмотров 3,6 тыс.3 года назад
A necessary tool for any 1-1/8” contractor, the BT-10 is designed to snap off form ties with minimal effort. The key feature is a special three-slot, alloy steel tool head made from the same steel in fine chisels carefully through-hardened to give it the wear resistance and toughness to strip many hundreds of foundations. Angled side slots make it easier to reach both high and low ties. For mor...
CC - Corner Clips
Просмотров 2,2 тыс.3 года назад
Replace standard 1 x 1 outside corners with low-cost, versatile, and nearly indestructible CC-90 Corner Clips. Can be used on any size panel. One set of clips can replace many sizes of standard corners. For more information check out our website: steel-dog.com/cc-corner-clips
RTOF Offset Ties
Просмотров 2,6 тыс.3 года назад
Steel Dog® Offset Ties are precisely bent resi-ties meant to strengthen offset section of foundation walls where it is not possible to use a straight tie. Made for most common combinations of wall thickness/wall offset. For more information check out our website: steel-dog.com/rtof-offset-resi-tie?rq=rtof
STT - Stud Tie
Просмотров 8703 года назад
Steel Dog® Stud Ties provide a quick, secure way to attach formwork to existing 3/4" headed weld studs (shear connectors) with 1/2" coil rod. Special coil loop and retainer clip combine to make a secure in-line connection of 1/2" coil rod to weld stud. For more information: steel-dog.com/stt-stud-tie?rq=stt ®Steel Ply is a registered trade mark of Dayton Superior Corporation
Stud Tie: How To Install
Просмотров 7733 года назад
A quick demonstration of how to install a Steel Dog® Stud Tie with a Nelson Stud.
Rebar Hook/Blind Side Wall - Steel Dog
Просмотров 5 тыс.3 года назад
Rebar Hook/Blind Side Wall - Steel Dog
Steel Dog One-Sided Forming - SCS Welding
Просмотров 6975 лет назад
Steel Dog One-Sided Forming - SCS Welding
This is a good concrete construction formwork method. This is South Korea.
Very cool products. They look very useful and save time. Thank you
Have to inspect and tag that scaffold too
How will the panels match up if they are set on a stepped footer?
You have to have a smaller Pannel
I set both sides of the wall at the same time with a setting partner. Fastest guy gets the ties in. I do like kicking panels off though. If you can kick them to the dirt bank is more efficient but if there is no bank and someone has to catch them it is still faster then prying them off from the ground level.
I’ve built a lot of foundations and I thought this video was awesome, fellas. Crack heads/boomers always commenting they can do it way faster 😂
canadian cribber here, who the fuck has two people to a wall? pick a side to pull from and everyone grab their own corner. one siding with two people? what it take you guys two days for a single family?
Do have to break them first
Very smart work...
semoga teman2 sudi mampir balek untuk menambah ilmu pengetahuan dalam bidang berkaria 🙏
semoga teman2 sudi mampir balek untuk menambah ilmu pengetahuan dalam bidang berkaria 🙏o
nice. thanks for the tip 💪🏽
Or simply buy Peri ... this is crap.
Love your guys stuff . I use it alot on my jobs .
Lol a guy on the inside feeding ties? Outside guys feed own ties inside guy try’s to stand his forms and catch him.
I found out that someone was spreading my name on social media and said SteelDog instead of SteelDog20 and now they have the subs that where coming to me 💀💀💀
Say you are my baka -Mahammad Gondi
2 year old video with comments only being a couple of months old ?? On a sidenote, 1-1/8 form setting is without a doubt the single best system in the world, ever!
Yuppppp
I am interested in ur technology can I get ur contact
I see gap between the boxes after closed that makes concrete leak a little , any answer about that
Okay, kind of thought I was going to get more information, but thanks.
Good
Have them for symons?
we do, yes. can be ordered through one of our distributers. email sales@steel-dog.com for more info
what price are they
we have dealers throughout the country who can get you a quote. email sales@steel-dog.com if you'd like more info. Thanks
Forget it you just don’t know what you’re doing, you don’t need someone putting ties in and you definitely don’t need someone kicking forms off for a guy to pick it up and put it back down. Then pick it up again and put it in a cage. If you’re making money now imagine how much you’d have if you did it right
You understand your yelling at the merchant, not the Sub right? Like a kid who's ice cream melted you decided to get upset.
@@patmaloney5735 you got me there, I don’t even remember posting this, just drunk and obnoxious for sure
Even if there was a mat of steel why wouldn’t you put a cage on each side and run it. Looks like it was a top and bottom row so I really don’t get why you ran one side. Edited because I was a dick the first time.
We are just the manufacturer, not the contractor. On the foundation shown here I think you're right, it could be formed in pairs quicker. This contractor does a lot of other houses where they've found one side first to be faster (custom homes with much heavier rebar, and commercial work where more intense rebar inspections are required).
Why are you only setting the outside first? I've done thousands of foundations with these and you always set both sides as you go.
Hey Ryan, it's true, these forms are designed to be set in pairs and in most cases that is the quickest way to set them. This crew builds a lot of homes with a large amounts of rebar, and that was the main reason they developed this system of setting the outside first. Similar to the way a lot of commercial work is formed when it's got heavy rebar that needs to be inspected. I'm sure on some jobs they could still set in pairs, but having perfected this method, they've found it more efficient to apply it to all their work.
I done the same way outside first
Weird, we have always done the inside first lol
You don't have to. You can do both sides as you go with Simplex forms.
Everything done the slowest way possible
What's the fastest?
Ya it’s a dumb fuck job and you have to be as dumb as the hammer you swing not to wear safety glasses wile breaking ties.
Neat. How do you make this beast?
I hate safety glasses too.....but I wear them.
Might get a form stuck in your eye
What a fucking clown
Hector Maraveles I think he’s doing a marvelous job