Видео

Uaaa

Thank you

😢

❤

btw: the hardest thing was to hide the baterries

Was there even water in it ,oh and there was no hole up front

Good luck

So, what the hell is the stuff you put in the lemon? ...Or the other random substances. If they're not labeled, the experiments are meaningless.

Cool

Whete is the steps in written form

Ayo, what's that lighter brand?

How much length of infusion tube and Syringe how much length is used

Good idia

OMG. There's 6 minutes of my life I can't get back.

Como lo ido ??

SO WHERE IS THE TIP ABOUT THE MATCH AND ELECTRICAL TAPE?? WHERE IS IT BUDDY?????

🎉🎉🎉🎉🎉❤❤❤❤

What did you use to get it to ignite

I got 1st prize 😮😮😮😮

Just put the piece in vinegar and Rusty boils off

Сгорят все проводки и люди. Убери свой совет. Кола быстрее справляется

Time is money 😂😂😂😂

destroy every floor you walk on with this one simple trick

RIP floors

Awesome.thanks❤❤❤

Super glue and paper works better and is more likely for people to already have on hand. Super glue and paper is also great for many other things. Like fixing the otter box phone case holster plastic clip. My otter box plastic holster that the phone in the otterbox case clips into broke in the middle of the curve of the clip. I first just use super glue like normal to glue it back together to get the alignent right, then when the super glue is cured I put a thin layer of super glue or CA glue over an area 1 inch or so to either side of where the break was. Then lay a small piece of paper over that and smoth down. Then saturate the paper with more super glue and add another layer of paper making sure to smooth out any air bubbles. So far it has lasted 10x longer than the clip did originaly.

Great idea, but you're a bit late since there have been devices around for tens of years that do exactly what your gadget does. Check it out.

Las medidas

Thank you for your video 🎉😊

At the start of your video you deliberately twist the shears to break the twig, same with the paper

Cool

Make a steam seperator addition.

Bro what did you use to fill in injection tube is it oil or water or what???

that is Great!! It will help me a lot for my math project btw, what was that blue liquid? ca I just enter water in syringe? PS. I will be thankful if you will answer me!

Было бы прикольно если бы он сам всё это делал😂😂😂

"Promosm" 💥

Pashlo nnnn

But wait, even to blow pressure the soda can's seal is not broke fully so how?

Its so simple. Tried out and ended with best results

alternating wind current :)

Desk worthy

WOW❤❤❤❤😊😊😊😊😊😮😮😮😊😊😊😊❤❤❤

youtube.com/@Mmghv424?si=lWZJxEB_FT6B8MBQ

It worked. I don't know about you guys but we just did this in school and it worked. Our turbine spun. Wait for the fire to heat up the can until the surface is burnt. The steam will come out. Now, for the turbine, you need to have a nice looking turbine, and make sure that the bended parts are facing the steam. Then, use a glue gun to make the turbine stationary on the steel wire. *The one that will spun is actually not the turbine, but the steel wire.* We did this on one go.

Não funcionou esse trabalho não recomendo fazer no final vai desmanchar por causa da água

7th liker

I’m the first commenter and the 5th liked!

Nice!

Cool

Interesting my friend 😎