Видео

Approved ✅️

Почему на шурупах а не на болтах? Или это на один раз???

Me gustó el último con el listón de madera

used a chisel to mark it off center, and proceeded to post a video showing you creating a cleaver way to create an off center sloppy fit up… nice

Great!

Teaches you how to do it, the measurements. A hug from Brazil 🇧🇷

When so called "expert" in the comment section tells you to spend money on tools instead of being creative.

I would use the table saw and be done in a minute.

Шикарно

Интересно

Don't believe him, it's not that easy 😅

Super handy jig - moving of the trimmer should always be the opposite direction though

Есть торцовка для этих целей, а это на отпил пары досочек, и менять.

Well that’s a cute saw/kerfing blade!

Dumb question but do u have measurements or template for these

is this stock 2inch thick (50mm) and thats why you used double row of dominos? (if so which size of dominos you used?) Thanks

That is simple but ingenious!

This model table is a useless one

А мне вот интересно кто сначала высверливает больше отверстие а потом в нем маленькое?...

Це СУПЕР! ❤❤

pas con du tout

이정도면 저게 빠지기전에 의자가 먼저 박살날듯

Китайские иероглифы ассоциируются с плохим качеством, это не лечится😢

I’d just use a dado blade on my table saw.

You tube censors comments

근데 돈은 왜 한국이냐

조용해서 좋다

What material Is that green?

I made one of these almost exactly the same only difference is I marked the base board like a protractor at every 10 degrees from 0 to 90 also the arm is longer so it can cut angles up to 90 rather than just 45 degrees

Nothing like a good jig

Нихрена он не равнобокий получился)

This is type of over engineering I did when I didn’t have proper tools or the space for them 😂 You’re in a shop, man, just build a router table

Геометрия, тот предмет на котором автор спал.

불쌍한 퐁퐁이들

형수님에게 이영상을!

에휴

Still waiting for the drilling part… I just saw a router doing normal router things

근데 본인도 까먹고 흔들었는데 비었네 하고 버리는 불상사가 생기면 미쵸버리겠는걸..ㅋㅋㅋㅋ

Table saw? Can't cut different groves. Router table? Can't stabilise as well and requires the object to move/fit onto the table. The comments here clearly divide those that do and those that criticise the actual makers

🟥이러니 재활용 쓰레기장에 돈뭉치가 계속 나오지~ㅋ 얼마전 울 아파트에 막걸리 팩에 100만원 넣어 둔 분 찾아가라는 게시판 붙어 있더구만 ㅋ (참고로 수표라 일련 번호 말해야 준다고 함)

남편 : 여보 내 WD 어디있어?? 아내 : 아 지난번에 쓰려고 보니까 안나와서 다 버렸어~~~

Looks like what a millennial does when they don’t possess actual skills.

난 이런거 이해가 안감.

락카도 아니고... 허술하면 망함..

이렇게까지 숨겨야 하는 ㅠㅠ

여태 안들키고 있었는데 님이 영상 올리는 바람에 들키게 생겼어요😢.

All you need is a triangular piece as a fence and bit of math. You can go all the way to 0° if you want.

What is the red and yellow tape ?

It was perfect!

Same idea but just attach the router to a small sheet of plywood, cut two slots on either side of the router then use two 1x1s and drill two holes for screws and thumb nuts. Then you can easily adjust the job for different board thicknesses.