- Видео 22
- Просмотров 16 527
Homa Pump Technology
США
Добавлен 24 сен 2018
Replacing a Cable and Field Voltage Change on a HOMA T Motor Pump
In this instructional video, National Aftermarket Business Development Manager, Tony Brunetto, will show you how to replace the cable on a HOMA T Motor pump, as well showing how to perform a field voltage change.
Tech sheet available at: bit.ly/3KtSpod
Website: homapump.com
LinkedIn: www.linkedin.com/company/homa-pump-technology-inc/
Tech sheet available at: bit.ly/3KtSpod
Website: homapump.com
LinkedIn: www.linkedin.com/company/homa-pump-technology-inc/
Просмотров: 332
Видео
Testing the HOMA Pump OC Series Impeller
Просмотров 635Год назад
In this video, we put the new HOMA OC Series impeller to the test with a variety of difficult solids. HOMA has long been a market leader in providing cutter and grinder pumps, and the HOMA R&D group was able to draw on this extensive experience in the development of our OC cutting system. These hydraulics break new ground in efficiency, performance and reliability, all paired with the same reli...
The HOMA Pump OC Series Impeller
Просмотров 594Год назад
HOMA has long been a market leader in providing cutter and grinder pumps, and the HOMA R&D group was able to draw on this extensive experience in the development of our OC cutting system. These hydraulics break new ground in efficiency, performance and reliability, all paired with the same reliable, high-quality motors that have been proven in our A Series solids-handling line. Website: homapum...
HOMA Pump Protection Sensors
Просмотров 349Год назад
In this instructional video, National Aftermarket Business Development Manager, Tony Brunetto, will walk you through the commonly installed thermal and moisture sensors in a HOMA Pump, as well as expected readings. 0:28 Klixon Thermals 2:07 PT100 3:33 External Seal Probe 3:47 Single Wire Seal Probe (One-up One-down) 4:09 Dual Wire Seal Probe PT100 Resistance Values are available on our website:...
HOMA Pump - Stator Installation
Просмотров 1,5 тыс.Год назад
In this instructional video, National Aftermarket Business Development Manager, Tony Brunetto, will show the correct technique to install a replacement stator in a motor housing. 0:00 Introduction 0:54 Cleaning the motor housing 2:21 Required adhesive 2:43 Dry fit the stator 4:14 Apply adhesive 5:59 Spread adhesive 7:02 Install stator into housing Instructional sheets are available on our websi...
Installing a Homa Pump GS1050 Go Switch
Просмотров 331Год назад
In this instructional video, National Aftermarket Business Development Manager, Tony Brunetto, will show how to wire a Homa GS1050 GO Switch Relay for monitoring moisture sensors and thermal protection. 0:27 Wire Markers 1:53 Wiring Supply Voltage 2:24 Wiring FM Cable Sensors 4:57 Wiring Non-FM Cable Sensors 7:23 Wiring Multiple Leakage Sensors Instructional sheets are available on our website ...
Tandem Lower Bearing Installation
Просмотров 5702 года назад
In this instructional video, National Aftermarket Business Development Manager, Tony Brunetto, will show the correct orientation for installing tandem lower bearings in a pump. Instructional sheets are available on our website bit.ly/3JQD2H6 Website: homapump.com LinkedIn: www.linkedin.com/company/homa-pump-technology-inc
HOMA Motor Cap Voltage Change
Просмотров 4652 года назад
In this instructional video, National Aftermarket Business Development Manager, Tony Brunetto, will show you how to change operating voltage on a HOMA pump equipped with a "P" Frame motor or larger. This procedure applies to A Series (AMS, AMX, AV(X), AK(X)) pumps equipped with a motor cap instead of a side cable inlet. Consult the nameplate of the pump to verify if it is equipped with a 230/46...
HOMA T Motor Voltage Change
Просмотров 3262 года назад
In this instructional video, National Aftermarket Business Development Manager, Tony Brunetto, will show you how to change operating voltage on a HOMA pump equipped with a "T" Frame motor. This procedure applies to A Series (AMS, AMX, AV(X), AK(X)) pumps up to 13hp, as well as GRP59, 79, and 118 pumps. Consult the nameplate of the pump to verify if it is equipped with a 230/460V dual-voltage st...
HOMA T Motor Teardown and Reassembly
Просмотров 1,3 тыс.2 года назад
In this instructional video, National Aftermarket Business Development Manager, Tony Brunetto, will show you how to take apart and reassemble a HOMA Pump equipped with a "T" Frame motor. This procedure applies to A Series (AMS, AMX, AV(X), AK(X)) pumps up to 13hp, as well as GRP59, 79, and 118 pumps. 0:00 Introduction 0:31 Removing the Motor Housing 2:38 Removing the Seal Probe 3:50 Removing Up...
Retrofitting a PMR5 Relay
Просмотров 2512 года назад
In this instructional video, National Aftermarket Business Development Manager, Tony Brunetto, will show how to retrofit a HOMA PMR5 Sensor Relay Module into a control panel. 0:00 Introduction 0:15 Installing the Module 0:56 Powering the Module 3:09 Wiring the Thermals 4:30 Wiring the Moisture Sensor (S1 & S2) 7:22 Wiring the Moisture Sensor (S3 & S4) 7:56 Wiring the Moisture Sensor (S1 & S5) I...
HOMA Pump - Profile Seal Installation
Просмотров 7792 года назад
In this instructional video, National Aftermarket Business Development Manager, Tony Brunetto, will show the correct technique to install a profile seal (gasket) into a HOMA guide claw. 0:00 Introduction 0:32 Installing 2"- 6" Profile Seal 1:42 Installing 8" and Larger Profile Seal 4:23 Conclusion Instructional sheets are available on our website 2"- 6" guide claws: bit.ly/3cBGTYL 8" and larger...
HOMA GRP Series Suction Cover Adjustment
Просмотров 3032 года назад
In this instructional video, National Aftermarket Business Development Manager, Tony Brunetto, will show the correct technique to adjust the Suction Cover (bottom plate) on a GRP Series Grinder Pump, as well as how to replace the stationary cutting ring. 0:00 Introduction 0:20 Adjusting Suction Cover 7:12 Replacing Stationary Cutting Ring Instructional sheet is available on our website: bit.ly/...
HOMA GRP Series Teardown and Reassembly
Просмотров 6532 года назад
In this instructional video, National Aftermarket Business Development Manager, Tony Brunetto, will show you how to take apart and reassemble a GRP Series Grinder Pump. This procedure applies to GRP models up to GRP50. GRP59, 79, and 118 pumps utilize a different motor. 0:00 Introduction 0:21 Teardown 14:00 Reassembly Website: homapump.com LinkedIn: www.linkedin.com/company/homa-pump-technology...
HOMA AMS Hydraulics Superior Solids Handling
Просмотров 1 тыс.3 года назад
The composition of wastewater has changed greatly in recent years, with a sharp increase in solids content. In order to ensure reliable operation in modern wastewater, our AMS hydraulics rely on closed single-vane impellers with large solids passages. Our impellers and pump housings have been redesigned at the HOMA R&D center and optimized with the latest computational flow dynamics software. T...
Thank you for the video. These are amazing pumps. I have two for a residential lift station lifting 50 ft. Have run for 11 years and now need to rebuild one. Is there a replacement motor part # nd sold by HOMA to replace the motor on a rebuild?
Model 178306 GRP 12/1 208V 5.98 Fl Amps
He is my grandpa, my grandpa
❤
Thank you!
Thank you!
Great pumps
Great
Thank you for the video ! I hopefully don't ever have to do any of this but good to have a reference .
Truth