Видео

Thank you, nice and easy!

Thanks for the info kid. Just posting to help with the algorithm.

Thanks 🙏🏼

Did you get the fuel injectors from the dealership?

I want the PINK COMB..... U rock 4 dayzz!!!

Too bad you scratched the crap out of it by grinding it on the pavement. Looks unpainted? I could be wrong.

Do you have to release fuel pressure first? I have a 1998 Tacoma 2.4

@JuniorTLafaille What type of bulb was it for the tail light?

Nice one 🎉 So tell me, what were the signs that pointed you to the thermostat and not the control temp sensor. I was trying to decide why my temperature indicator was stuck on cold and I was hoping it was one of the two sensors that sit next to each other. But then I felt that the coolant hose was staying hard , so that makes me think it was the thermostat. Anyway thanks for pointing out how to change it.

Thank you bro

Good 1

I did this but now its idling roughly and stalls with blue smoke out of the exhaust

What’s the purpose of this valve?

If I’m just replacing a tps I don’t need to take the entire throttle body out do I?

good job

Did you have to drain the coolant? When you take the sensor out how much coolant drains ?

your videos are really helping me figure out what's bugging my 1996. videos with the 2.7L engine aren't as easy to find as the 6s 👍🏼 thank u!

I like the way you explained

🙏🏾

Clutch

Nice

Easy

whats the toqure specifics of the nuts or bolts when installing bk in?

Remember do not touch the new bulb with bare hands, the oils from your fingers can blow the bulb as it heats up!!

What year is it? I saw another video where the guy changed it from top of the hood.

Thanks man I looked crazy trying to start it I rented one in Vegas😂

so what are the symptoms of a xterra pcv valve being bad?

💪🏾

How entirely NOT to change spark plugs on seriously deep set engine, you let the plug slip out of the socket when putting new one back in then started screwing straight away and you not using torque wrench on aluminium cylinder head, use a rubber insert plug socket ,and torque up correctly ie 25 Nm or one day luck will run out Bro.

My rental didn’t have any button for opening the fuel tank door. After searching for 10 mins, i realised i just needed to press the flap to open it ☹️.

Thanks so much!!!!

I appreciate your advice I'm going to do that

It would help to say how the injectors go in and out. Do you twist or just pull?

I need to do this on a pathfinder. Is it similar location on that?

Does anyone know if you can add a nitrixcockside to this model car?

This is horrible stop making videos

Hi i have a 98 Pathfinder 3.3L. I inspected the bottom inside of distributor (under the coil) and the shaft only had about half the ball bearings in it. Could this cause random misfires in all cylinders, P0300 code? The plate that covers the bearings was broken off/loose too. Thanks!

Thank you so much for sharing this video to change the PCV valve. I own a Suzuki 2005 XL7 and it has excessive smoking from the exhaust on startups. I suspect that it may be a clogged PCV valve. Did you have similar problems with your XL7 prior to changing the PCV valve ? Did it help by changing the PCV valve ?

Did the idle go down by itself. I changed the iac valve not tps and its idling 1300 waiting to see if it will go down after driving.

It's better to take the upper air box off and spray the sensor through the tube that way to reduce touching or risk of dropping and damaging it as much as possible.

thank you for the video! i have to do the injectors on my 99 4runner

Hello..what happen if the spiner spin freely?the distribuitor is broken?

Could this gasket cause the engine to run lean? I redid my intake manifold gaskets and reused my TB gasket which was ripped halfways and snapped a stud when torquing it down. I didn’t have the problem before, only p0401 which finally cleared out

I got a used truck from my friend and its the 2000 model and the fuel injectors are pink and I bought the same one but the engine struggle to start , and I can feel its weak and it backfired sometimes

We want to know where the rest part you had that i had same and you didnt show where it is at

Thank you

Great work

Thank you I was afraid I would have to remove the entire throttle body.

On my own Tacome, the stud bolts in the back have Torx ends, but apparently you don't need a female Torx or anything like that to remove those nuts (at 0:40)? Also, do you have to oil the gaskets on the install?

Great video but I had a question. I did my 2004 2.7 just like this but when I out it all back together the engine won’t stop revving up on its own. Any idea on this?