Видео

Hi @HurdCrafters, thank you for your question! The top portion of the fence is 35.4 mm thick (close to 1-3/8”), and the lower portion is 28 mm thick (1-1/8” or close to 1-7/64”). The 3” fence end is 17.7 mm (45/64”) thick.

@@powertec_usathank you!

Hey @ResinEssenceByCheri! Unfortunately, Skil routers are not compatible with the 70331 dust collection system. Let us know if you have any other questions!

@@powertec_usa 0:42 might change your video then

Hi @One_Call_System, thanks for reaching out! Please email us at info@powertecproducts.com, and we'll be happy to assist you.

Hey @GuitarHeroPhenomSux, sorry about the mistake! We've fixed the title.

Hi @herbsu4330, great question! Use a square to adjust the front fence to be square to the kerf line in the base. When square, clamp the other end of the front fence to the base. Note that the runner (HDPE bar) is 3/4” x 3/8” for universal 3/4” miter slot.

@@powertec_usa My question regarding the bar was what if there is play when it is in the miter slot or if it is too wide for the miter slot.

@@herbsu4330 I've not tried this, but I wonder if you either tighten the screws near the slack areas, or put slightly "fatter" screws there, if it would push the HDPE to be wider at those locations so it would take up some slack? At 1:37 in the video he talks about screws expanding the HDPE bars if the holes are too small in diameter. You could use that to your advantage.

@@Part_121 that's a great idea

Glad it was helpful, @CAHOBBES!

Hi @miltoncabrera4073, glad you liked it! The clamp slot measures 12.4mm (width) x 6.9mm (height) with an 8.7mm opening.

Hi @JordanLargado, please visit the below link for all relevant info: powertecproducts.com/70136-4-to-2-1-2-cone-reducer/

Hey @imagineengine, here's the link 👉 powertecproducts.com/bs900rf-rip-fence-for-powertec-bs900-wood-band-saw/

Hi @b3owu1f! Unfortunately, the MT4009 will not work and is not an option for the SawStop. The SawStop footprint is larger than the MT4009, and there are no mounting holes to attach an adapter board.

@@powertec_usa So just a heads up.. I ended up going with another brand (sorry.. was $20 cheaper) the black/yellow version of this. Turns out.. you CAN fit the sawstop compact on it.. but you DO have to rig it a little. For example, I am using I think 1" ubolts.. and by adjusting the yellow (green on your unit) plates a little bit you can line them up below both legs. I am also using some ratchet straps as extra support. But it works. So it CAN work, it just requires a little extra work to mount it. I should add that the height of the saw is pretty high.. I have the Kreg fold up table (that you get with the track saw setup) and the table saw sits higher than that by a couple inches. As well the Kreg stands, at maximum height are too short to act as a feed table or side table (with some plywood on it). So.. I am building these in/out feed stands from wood that I found to work with my saw and stand.

Hi @simjeeu, quick release ratcheting table clamps are compatible with Combo T-tracks and Miter Tracks (available in 32" and 48" sizes). They are also great when used with track saw guide rails!

@@powertec_usa thank you!!

Hi @gaelliottry, we hope you'll make great use of it! We'll be delighted to hear your feedback once you've had the chance to try it out.

@@powertec_usa got to use it today and it is awesome! Saved me some money compared to the competitions too.

So happy to hear that!

Hey @atchmon902, just a heads up - you might want to double-check the stand's specs to see if it matches your table saw model. The stand can hold up to 331 lbs (150 kg) and fits spaces up to 20-5/8" x 18-1/2" (52.4 cm x 47.1 cm). Let us know if you need any more info!

Hi @jimsprague9309, Before enlarging your 2.5” port, please check the 6hp shop vac, cyclone cleaner, and hose/pipe for any clogging. Also, check and see if the cyclone container is too full. (When the cyclone container is too full, it will reduce the suction power). Typically, a cyclone is more efficient and easier to clean than your vacuum filter, but for a big chunk, like planer shavings, it can easily clog a 2.5” hose/pipe/cyclone system. The table panel kit creates smaller debris, and dust particles and a 2.5” port should be big enough without clogging. In addition, if you connected a long hose/pipe and a lot of adapter/blast gates, it also reduced the suction power. If you have checked and there is no debris, chips, or clogging in your system, connect your down draft table directly to your shop vac. If you are still not getting a good draft, your shop vac hose may be too small, or you may not be pulling enough CFM’s. If you have more questions or require further assistance, we encourage you to message our Customer Support at info@powertecproducts.com. Cheers!

Hey @trustno1785, we haven't tested your model, but there's a way to find out! The guide rail adapter uses two sets of mounting rods. Simply check the rod distance and size on your router, then compare it to the specs of the adapter on page 2 of the manual: powertecproducts.com/content/71085.pdf.

Hi @datFUNKYb! Just wanted to inform you that the Router Guide Rail Adapter System is now available for purchase. Cheers!

Hey @str8tfromtexas, thank you for your interest! Adapters and fittings will be available for purchase separately very soon. Please stay tuned for the announcement.

Hi @jaybeasley8600, it does! The router table fence mounting slot ranges from 18-1/8" to 23-3/8".

Agree..how is that made?

It comes in two pieces. You don't need to cut it.

@@n8thegr8 I think he's talking about the slot that was cut to hold the T-track, not the separation between the two pieces of T-Track.

My guess is you're going to need a router with a straight bit the same width as the track. Setting it up is going to vary quite a bit if you have a router table vs not having a router table.

Hi @raymitchell9736, thanks for reaching out! We're here to help with your dust collection setup. Just email us at info@powertecproducts.com, and we'll take it from there.

Hi @raymitchell9736, thanks for reaching out! We're here to help with your dust collection setup. Just email us at info@powertecproducts.com, and we'll take it from there.

Hey @tedperez4732, great question! When it comes to length, the choice of a band saw blade depends on your machine, while the size of your saw's wheels will typically determine the maximum thickness of the blade you can use. Depending on your application, there are a number of variations within a blade size. Blades widths, the number of teeth per inch, and the material type of blade can all change depending on your application. When buying a blade, check the listing to make sure it meets you needs. We hope this helps!

@@powertec_usa gracias. I'm in Baja 🇲🇽 but commute back and forth between San Diego for weekends. I Amazoned a Timberwolf blade and package was stolen before I could get it lol. I finally got replacement blade and I hope to install it this weekend (for my bday present)

Hi @DogIslander1, we're thrilled to hear that you're enjoying our table panels. Those red plugs are an additional cool feature of the panels - they function as bench dogs for your workpiece. Simply install the stops into one of the designated holes and press your workpiece against them for a hold that won't slip.

Thank you @freelanceavenuebd!

Thank you for your comment @travelwell8098! Glad it helped!

Yeah they absolutely do. I don’t know why they said they don’t

Hey @NickLM2008! While we don't have a specific distribution channel in Australia just yet, we do ship internationally through powertecproducts.com. You can also find our products on Amazon. Feel free to check them out! 😊

Hi @bniemann420, thank you for your comment! We are excited to confirm that our R&D team is working on a 2-1/2" Quick Connect Dust Collection Tool Adapter. Stay tuned for updates! Meanwhile, we recommend using the below combination to connect your 2-1/2" hose to the 4" Quick Connect Dust Collection Tool Adapter: 1. Connect your hose to the 70136 4" to 2-1/2" Cone Reducer: powertecproducts.com/70136-4-to-2-1-2-cone-reducer/ 2. Connect the 4" side of the reducer to the Quick Connect Dust Collection Tool Adapter using the 70149 4" Dust Control Flex Cuff: powertecproducts.com/70149-4-dust-control-flex-cuff-with-hose-clamps/ You're all set!

Hey @badtolz2122, thank you for the comment!

Hey @michaellullo8931, we truly appreciate your feedback! The Powertec track saw guides, 71153 and 71387, are aftermarket guides that can be used with several different brands of track saws. Although the track saws fit and work with the guides, not all accessories, for a specific brand, will work. The Festool accessory kickback stop is one of those accessories that will not fit our guide. Makita and other brands do not offer kickback stops as an option but handle kickbacks in other ways. In their instructions, Makita states: “When using the tool with guide rail place the tool on the guide rail with the rear edge of the tool base against a fixed stop or equivalent which is clamped on the guide rail” SP600 page 11. WEN states that their saw has anti-kickback knobs, mounted to the saw, and does not mention kickback stops in their instructions. Here are some suggested solutions for creating a kickback stop that will work with our guide: 1. There are third-party options. ToolCurve offers a set of stops that they advertise as being compatible with Powertec Guide Rails. They can be contacted through the following link toolcurve.com/product/powertec-guide-rail-limit-stops/. 2. As Makita suggests, clamp a fixed stop to the end of the guide rail. 3. Make a guide rail stop, as demonstrated in this RUclips video titled "Guiderail Stops - simple, easy & cheap to make": ruclips.net/video/CHyL_qPgrDc/видео.html. Please let us know if we can be of further assistance.

Hey @17penobscot! Could you specify your question a bit more? We want to make sure we get it right for you!

Hi, @almosthuman4457! Thanks for sharing your thoughts! We totally get that everyone has different tastes. At the end of the day, it's all about the product.

Hey @christopherdekonstrukt444, thank you for your comment! Ensuring affordable prices without compromising on quality is a priority for us. Let us know if you have any questions!

Hey @ms13352, thank you for your feedback! So sorry to hear the plan did not work out for you. May we ask what type of adhesive you used for the project? We recommend using Super Glue of any brand and applying pressure on the fiberboard to ensure full-surface connection with the miter bars. Ideally, the sled should sit for 24 hours to completely set. Also, before gluing, make sure the holes are predrilled, countersunk, and that the screw holes are a little larger than the screws. This step will help prevent the screws from swelling the HDPE (making it too tight), and keep the screw from grabbing and breaking the HDPE loose from the board. We wish you great success with your future projects!

@@powertec_usa three different types of superglue. Does not matter now. Junk

Hi @T-C-C, thank you for your comment! You are absolutely right, it is extruded aluminum.

Yes I noticed the voice over guy mispronounced extruded :) @@powertec_usa