Видео

I just picked up a 2000 4runner with 70,000 miles. I noticed the breaks are a little sketchy. I looked it up and the breaks are just really underpowered for this gen. It has aftermarkey rims on there and was wondering what you did to clear the calipers? Do you already have 17s or did you have modify anyting if you have 16s?

Did you use any specific type plywood?

What fuse did you use to connect the switch pro ?

you did everything really well. i just wanted to know how thick a gauge of wire can fit inside the front and rear door sills and also how much room you had going through the b pillar. i want to install the thickest gauge wire that will comfortably fit from my battery to the trunk. thank you!

What wire sheath did you use to run the wire from the rack down the rain channel and windshield?

how bout for the front differential ?

What’s the socket size and type you’re using?

What cord did you use to connect the radio to the RJ45/CAT6 port?

Great video, thanks!

Thank you for sharing, appreciate the detailed video. I have an engine mounted arb without the extension hose. Wondering how it’s held up so far. Anytime I air up it get extremely hot. Has this caused any issues with the pump overheating or hose failing ?

why did you decide to put it on the top hole rather than the lower one?

Super cool look at the rear drains with that scope! Vid deserves more views

Thank you sir! I'll do the same install but on the passenger side (there is an open space in the upper left corner when facing the engine) using the LFD Offroad mount for the 5th gen 4Runner. I have the SwitchPro 9100 as well but it is on the other side of the engine bay so I'll have to run those wires plus power and ground. Hopefully it all works out!

Just installed these on my 24, Land Cruiser and I will recommend these ALL THE Time. The 1958 edition Land Cruiser is comfortable as is but these made it even better. If you are on the fence about them, just do it. So much more comfortable and a really simple and quick install.

How is this setup holding? On the Proclip website, they are saying that the clip cant hold the tablet. Do it still work fine?

Thank you perfect video

What are you using to hold the mic? I am wanting to have this exact setup. I have been looking for a super clean install that doesn’t require drilling of the body/dash and is easy to hide when not in use.

Obviously an older video, but you want that bottle above the bleeder screw.

Awesome

What front bull bar is that looks awesoem

OverlandEd, I am preparing to do the 13WL upgrade for my '00 v6 4runner and have two questions so far: 1. Have you had any ABS issues with the 13WL upgrade? (There is some scuttlebutt on forums about this so considering 13WE instead) 2. I will upgrade the soft lines to stainless steel and the vendor asked if I wanted to bypass the caliper side hard line with a longer flexible line. Would you do this? Once again, thank you so much for your videos and advice!

You put the holding pins backwards. They are too close to the rotors

Thank you for the good instructional.

Heat is your best friend. A bit goes a long way. Good work though.

Could always go back and check torque after a few miles on and off road to see if it stays tight.

Excellent video! Straight forward explanation of what you are doing and why also your video work is clear and concise. Thank You.

Great video. Hi how well has the gauge wire you used holding up. I am planning to run a line to the back for rear cargo area and trying to see what gage will be adequate. Thanks

Nice but too bad they don’t make for the rear too anyways how you mount the fire extinguishers?

This is the video i have be looking for so long! Would you be able to show a wiring tutorial for the chase lights? Thanks for the great video and insight

Good video . Just subscribed.

Amazing you gave me confidence on doing my own Thank you sir

very well done

Easy to install but hard to remove

شكرا على الشرح

Thanks for this....

Looks great!

Beautiful 3rd gen‼️😎👍🏽

Does it fix the lean?

How hard was it to remove the head liner? I need to replace all 4 of my roof rack brackets because the white pieces are smashed down.

Beautiful truck! 3rd and 5th gen are said to be the best generations. I love the 3rd gen. I have 99 4WD limited w/ E locker. Bought the truck with the Caliper upgrade. It’s squeaking and a little spongy, not sure if that’s normal. Going to rebuild the calipers, or I may just have my mechanic do it. Yours is super clean. Ok thanks for the vid

I like your videos! I got several ideas from this one! I am a novice at modifications and inexperienced as a mechanic so the more detail you put in the better for me! Don't hesitate to show every step in my opinion!

Can you explain why you didn't want to end the rear breathers in the gas filler area? Were there any major cons? Placing the end-breather here seems much easier.

how tall are you? do you hit your head on ceiling now?

I want to thank you for your mess up and most importantly your fix. 😏 Good job

This is definitely my most favorite Nauset oversand video

Genius!

Great vid, did u purchase the steel or aluminum skids?

Wish I could do this on my Prinsu. Tried the same way at first but it hits my hatch, so I ended up mouting it to the sides 😭

Need heat to melt the lock tight

How did you get the antenna cable to stay in the windshield channel? Is there anything actually holding it in the channel, or is it mostly laying there. Great install vid though, thanks!