- Видео 5
- Просмотров 7 271
Almost Exactly
Добавлен 18 окт 2011
Видео
How to set up a Expert SPE 1 3K FA with an ATU installation
Просмотров 3,9 тыс.7 лет назад
Showing my install and set up of the ATU into the Expert SPE 1 3K FA that was originally bought without the ATU
How to ground the ANAN 100D Apache Labs PTT output connector Part 2
Просмотров 4367 лет назад
ANAN-100D PTT OUT ground issue Part 2
How to ground the ANAN 100D Apache Labs PTT output connector Part 1
Просмотров 9197 лет назад
ANAN-100D PTT OUT ground issue Part 1
4kv on the plate maybe 1.7kw ... lets see . the meter shows 2800v at lets be generous, .650 a so 1820 watts , but at 65% eff = 1183 watts :) just saying...
Are those Henry wired 220 volts or 120.
I have a 3K for sale. Thanks for your presentation.
You state the anode voltage is 3000 volts and the anode current is about 600 mA. That's 1800 watt input power. You say it's putting out close to 2000 watts! How does it do that? One of your meters seems to need calibration! I have a Henry 2K Classic and it sure won't do that!
Hi D..., you mention the other amp as the KWS1, but I only saw a 30S1 next to the Henrys. I use the 30S1 with my 7000dle, and also experienced the no gnd continuity. Same case, same problem. Not sure if you use the 30S1 with your Anan, but K101 in the amp had no back emf protection diode, nor does the 2N7002 transistor in the Anan have any. I added one across the K101 coil. cheers....
Jim is correct, the 2KA is about a 1300 watt output amp. The Eimac 3-500Z data sheet makes that very clear at the actual plate voltage available..
@@davidgow5648 The 2K-3 in my shack puts out 1700 watts on all bands into a dummy load. That's output power. The 2K-3 voltage is about 3200 volts, closer to 3000 key down. My data sheet shows 1480W plate output power (for two tubes) at 3000 VDC in grounded grid with about 92 watts drive.
That's what I need for sure very very nice 👍
External relay isn't a bad idea, but the Henry 2k-3 doesnt need one.
Looks like great clean classic amp. Need help, Do you need to use a ex relay for keying it from a FT1000mp or ic7300 ?? Tnx
Nice info. Would appreciate if you could confirm that relay is only required to protect radio's transistor should the voltage is over 25V and/or current is over 800ma.
You're correct. I used the relay only to prevent damaging the transistor in the Anan.
I have a new 7000DLE MKII, 2020, Black .... Same problems. Apache Labs hasn't learned that paint doesn't conduct. Every screw is painted and every hole is painted. None of the chassis parts are electrically bonded! I suggest removing everything and grinding the paint off under each jack and screw.
Beautiful amplifiers
Is the light you are using a mercury vapour type?I had the same problem with one you need to be careful with them also if they break the dust out of them is toxic. Never had problems with light bulbs when we used incandescent type
brother I here sounds coming from my light bulbs that msle me extremely ssd
So sorry I’m responding late. The ATU was $1500 USD made by SPE and shipped from Bob Hardis www.expertlinears.com/index.html He and his wife run a nice operation. My non-ATU SPE 1.3k-fa was purchased from Hardis about 1 yr ago for $3600. Cheaper to buy both together but I couldn’t afford both at the time. The non-ATU linear has worked nicely. the addition of the OEM ATU helps and basically has made the amp faster to tune, without having to use my external manual tuner. Thanks for your very nice comments. Happy New Year. Is it time to save up for SPE version II! Although I admit I’m happy with my version I. 73 Dave
Easy task. Tnx fr video. How much was the ATU board? I'm wondering cause, I was told that the single ATU will not sold when you purchased the NonATU 1k3. Thanks God, I do have only resonant Antennas at home but for portable use, the ATU would be an advantage or just to have this little "bastard" baby complete.😎. How much is the single board? Is this an SPE or aftermarket ATU? Good Job! TNX agn!
Great demo! I hope that you are now using the 1.3Kfa software instead of manually using the kepad. I love mine. Space saver and does the work. 73 Rafael / NN3RP
Thanks! I'm getting familiar with how to interface software and looking forward. Love the 1.3! especially now with the latest firmware and some updates.
Did this mod actually fixed the issue? I am having similar issue with 7000DLE where the PTT In produces not proper audio but gibberish and no output (watts).
Yes, PTT is fixed on my rig. Works totally reliably now.