Видео

It's definitely not at low idle, but mid range throttle. I only use enough throttle as needed for the task. I can feel the machine if it's too much or lugging the engine. Thank for the good observation. I guess it does seem quiter on video.

@@tommylifeisgood6144 I'm the same when it comes to running equipment. I keep the idle low for the sake of fuel and wear. I feel like for hard digging tasks it's good to keep it running higher though. Stalling it out is harder on the pump I think. Nice video, makes me think I may need a stump bucket. Lol

@@Ewaugh69 Actually good point, stalling is much harder on it. Also, I have better results with pallet forks pushed together in the center than stump buckets. The forks go deeper and rip roots much easier than digging them with a bucket. Try the forks first and you'll be surprised how easy it is to push a 20" diameter pine over.

Thank you for watching. I have definitely enjoy working with this old iron.

You have a supply and return lines, two lines. The grapple is a simple cylinder in/out motion. The right steer level push in or out changes the flow for the grapple to grip or release. So yes!

Watch my L781 video with the grapple. It's almost exactly the same as L555

Thanks for the quick response! I'm currently looking at a 87 l555 delux for my first skid steer. I only noticed one female fitting on the boom. Are you saying there should be another aux line close?

There should be both lines on each side of the boom.

I'm trying to add a picture but it wont let me.

Pushing on the tree gives more leverage to break roots apart etc. If you cut the tree and try to dig the stump, it takes much more power and bigger equipment. Basically using gravity and leverage to do the job more efficiently.

Also thank you for the comment, I asked the same question long time ago. I found the answer on my first tree. Lol

I have no clue.

Yes it was.

Yes, totally my fault but ended well.

I agree and thank you!

No, I didn't have any noise at all. I found my worn bearing doing maintenance on it.

Sorry you feel that way. That old machine is engineered to work and does it well.

Great point, I will try that on my next tree. That does make perfect sense to clip the smaller diameter roots further out. Thanks for the observation!

Thank you very much. It was our first visit to the port since completion and wanted to show others. A significant upgrade compared to the old port.

I'm going to build a larger one later. This was my first try at it.

I really enjoy working on the loader. I'm going to get more attachments to do more stuff.

Lol... lol

I was thinking the same thing. Do you think the tight tracks would strain the axle bearings??

Amen!

Totally agree! They were locked from the inside. The older NHs had large pins that protruded out to prevent the arms from coming down. I should have mentioned that.

I've thought more of your advice and I appreciate it. Usually accidents happen when we get rushed or distracted, like I was at that time. Even though the arms were locked, the loader was still running. I need to slow down and think before I exit a running loader. Thank you @robbobcat7286 for reminding me.

Amen! They are so brave!

Watching it gave me goosebumps!

Oh I'm sure. The American military is nothing to laugh at.

@@ericerto8250 if you look up Iowa class battleships, you will find 4, all of which you can actually go on. There are several different class battleships that have been made into museums, all cool to see. Find one closest to you and check it out.

Thank you and I definitely will check them out.

Thanks Nick!

Thank you, I definitely had fun clearing the pines with this loader.

@@tommylifeisgood6144 I'm getting a kubota SVL 75-3 next week

@@rayrayslawnlandscape2008 Sweet machine and I would love to own one.

I love the old iron. Thank you!

I have a set, but haven't installed yet. I agree, lots of spinning the tires. I'm definitely going to install soon so I can clean up brush piles down the hill. Thank you

The narrow stump bucket can dig deeper with more force compared to a regular bucket. I can remove small trees and bushes so easy without tearing up the ground. I also use it for trenching, laying gutter pipe, digging up large rocks, etc. It's a great tool to have in the tool box for sure. Thanks

No, just the bearing on the axle and race in the housing. I would get parts from East Coast Gear Supply, great pries and quality parts.

@@tommylifeisgood6144 Thank you kindly! Sorry for the late reply. I don't have access to a press so I ended up buying the Crown one that is completely assembled and keeping this axle as a spare.

The bears were passing by the cabin in and out all day. We had a blast watching them.

@@tommylifeisgood6144 that is awesome stuff….there is no joy like watching nature in action. I love the bears 🐻, thank you for posting

I hope the video helps you. Keeping digging to break roots all the way around the root ball. Good luck and take a video!!

@@tommylifeisgood6144 thank you….your video was an instant help.

Add a loose feeling, I changed out the crappy Rubicon track bar with a monster Teraflex and it felt much better.

@@tommylifeisgood6144 ok great thank you I have to to the same thing to my 93 zj

Thank you very much! I'm not good at editiing videos, I just enjoy working the skid loader and share my experiences.

Push the rear side of the jeep back and forth. You will feel this type of axle slack.

Thank you, I agree. I do have a set of traction metal tracks to install. Now, I'm afraid the extra traction might break a chain instead of wheel spin on this old loader.

That's awesome!

I didn't measure the play, just significant noticeable. Once I changed the bearing, the play was eliminated.

Loflin bucket, I bought it about 22 years ago. All my buckets except one are Loflin, made in Denton, NC. Thanks

Wow talk about longevity I need me one, great video thanks for sharing

Thank you very much!

just ordered a Loflin bucket, just like that one-hoping to get the same kind of service you have gotten from yours--thanks nice video!@@tommylifeisgood6144

It was a little bumpy, but normal for hard packed red dirt in a hurry. I need to slow down sometimes. Thanks!