- Видео 22
- Просмотров 50 778
Mike Morris
Добавлен 12 июл 2012
Engine Lathe Basics
This is a video on how to set up a manual lathe. We are going to turn a 1 inch diameter shaft back 6 inches. The shaft has three steps. Each step is 2 inches long. The largest diameter is 0.900, the middle is 0.800 and the smallest is 0.700...
Просмотров: 16 255
Видео
Tramming The Head
Просмотров 24110 лет назад
This was done using a rotor that was surface ground both sides. The most common was would be to use 4 (1-2-3) blocks.
Laser class 1
Просмотров 3,6 тыс.10 лет назад
Importing a DXF file into the laser and engraving a butterfly on a piece of plastic.
Mastercam (Topic3.7)
Просмотров 64110 лет назад
This video was created by Mike Morris at Orangeburg-Calhoun Technical College. This workforce solution was funded by a grant awarded by the U.S. Department of Labor's Employment and Training Administration. The solution was created by the grantee and does not necessarily reflect the official position of the U.S. Department of Labor. The Department of Labor makes no guarantees, warranties, or as...
Mastercam (Drill)
Просмотров 1,5 тыс.10 лет назад
This video was created by Mike Morris at Orangeburg-Calhoun Technical College. This workforce solution was funded by a grant awarded by the U.S. Department of Labor's Employment and Training Administration. The solution was created by the grantee and does not necessarily reflect the official position of the U.S. Department of Labor. The Department of Labor makes no guarantees, warranties, or as...
Mastercam (Pockets)
Просмотров 1,1 тыс.10 лет назад
This video was created by Mike Morris at Orangeburg-Calhoun Technical College. This workforce solution was funded by a grant awarded by the U.S. Department of Labor's Employment and Training Administration. The solution was created by the grantee and does not necessarily reflect the official position of the U.S. Department of Labor. The Department of Labor makes no guarantees, warranties, or as...
Mastercam (Contour)
Просмотров 93310 лет назад
This video was created by Mike Morris at Orangeburg-Calhoun Technical College. This workforce solution was funded by a grant awarded by the U.S. Department of Labor's Employment and Training Administration. The solution was created by the grantee and does not necessarily reflect the official position of the U.S. Department of Labor. The Department of Labor makes no guarantees, warranties, or as...
Mastercam (Back Plot)
Просмотров 1,8 тыс.10 лет назад
This video was created by Mike Morris at Orangeburg-Calhoun Technical College. This workforce solution was funded by a grant awarded by the U.S. Department of Labor's Employment and Training Administration. The solution was created by the grantee and does not necessarily reflect the official position of the U.S. Department of Labor. The Department of Labor makes no guarantees, warranties, or as...
Mastercam (Machine Group)
Просмотров 2,9 тыс.10 лет назад
This video was created by Mike Morris at Orangeburg-Calhoun Technical College. This workforce solution was funded by a grant awarded by the U.S. Department of Labor's Employment and Training Administration. The solution was created by the grantee and does not necessarily reflect the official position of the U.S. Department of Labor. The Department of Labor makes no guarantees, warranties, or as...
Water Jet
Просмотров 21510 лет назад
This is our new Water Jet @ O-C Tech... In this video, I'm cutting wood. The machine is capable of cutting through 10 inches thick of metal. One problem, you better have a mop close by. Water gets every where.
Importing images using Autodesk Inventor
Просмотров 11 тыс.11 лет назад
Importing images using Autodesk Inventor
Module 1 PlasmaCam Topics 1.1 - 1.4
Просмотров 1,7 тыс.11 лет назад
Module 1 PlasmaCam Topics 1.1 - 1.4