Видео

Thanks with love and many prays.

وعلیکم السلام و رحمت اللہ و برکاتہ Use air blower and remove dust from every part. Open scanner unit and clean lens very carefully.

A big Thanks for appreciating.

It depends on noise type, in most printers noiase is because of these faults. Toner catridge is heavy and not rotating smoothly, swing gear is slipping, motor gear, and some times paper pickup rubber stuck and gears are continuously touching.

Its without commentry

Congratulations! You are already a Surgeon of Printers. 🤗😜🤣

Reason posibally Fuser/Heater When it overheata sometimes it makes copier slower.

Stapler and Common pins and white wash pieces cause damage to OPC (drum) sometimes also damage PCR, also damages Fuser Film /Sleeve.

السلام و علیکم و رحمت اللہ و برکاتہ۔ Posibaly ECU (power supply) problem. Because when to try to print at that time it cant stable voltage of formatter and then printwr restarts. If you are aware of printer hardware open its ECU (Power Supply) side and see, Filter Capacitor is about to be replaced mostly its 400v and 68uf to 120uf value.

@@PrinterSurgeon hardware issue? phr is ka kaya hall huna

@@creative_world-qe3oo Repair, Consult any Printer repair shop.

وعلیکم السلام و رحمت اللہ و برکاتہ۔ Its not printers fault, its your printer drivers issue. If your printer is a P2015n/p2015dn then connect it on a network and open its configuration page in browser and check for printer configuration and make changea accordingly.

Thanks a lot

In some cases if the formatter processor is not working properly and was over heated and lost it's soldered bubble contacts you can do this risky experiment if you have knowledge of electronics. But If you are sure the problem is with processor proper method is to remove the processor using SMD Rework Station and re-solder is using SMD Rework station. I tried this method without consulting any video or senior. But success ration was only 10-20%. But you can do this experiment if you don't have alternative formatter board. But I suggest, use thinner on board and wash it well using a paint brush or old tooth brush and wash its rust and dust thoroughly and put it in shining sunlight to become dry. Then check it. If it doesn't work then you can do experiment.

@@PrinterSurgeon Thank you for the answer and for the precious helpful information... I will try to use the blower of a station at a temperature of 250 degrees Celsius, after you clean the plate of the former with isopropyl alcohol and a brush... all I have left is medicinal alcohol, but this it is not suitable for smd contacts... if I don't succeed, I will buy some chicken eggs and make an omelette with the pieces of the formatter board... good health and beautiful days ahead

@@zarzarel1910 🤤🤣

جزاءک اللہ خیر

@@PrinterSurgeon و ایاکم

Thanks for watching. I uploaded in hurry, Now I have uploaded subtitles you can see in your language. I hope now you will understand easily. My intention is views only but to teach true knowledge.

Yeah! AGREED! "seeing what you do is enough!"

Sorry I didn't understand your question. Do to want to connect your RICOH Printer to a mobile?

@@PrinterSurgeon yes.

@@lootzone2.0 Download RICOH application from platatore (if availavle) or use third party application and attach printer via OTG (If your mobile supports OTG).

@@PrinterSurgeon third party app not supporting. Printer detect ho rahi hai lekin print nahi nikal rahi hai.

Just clean scanner lens of HP LaserJet P2055 and don't tune variable setting. Watch my playlist you will find video or in a video about it. Change toner powder and use static toner powder if you want to increase result.

Thanks to you aa well for appreciating my work.

Thanks for appreciation.

شكرًا جزيلاً، على استعداد لمساعدتك في أي وقت جزاءک اللہ خیراً کثیرا۔ Thanks a lot, Ready to help you any time.

في HP LaserJet 1300، يعد وميض الضوء البرتقالي خطأً شائعًا. وهذا بسبب قضايا مختلفة. اولاً، هناك انحشار للورق داخل الطابعة، ثانيًا، لا توجد خرطوشة حبر مثبتة. ثالث. خرطوشة الحبر معيبة، أو أن الطابعة لا تقبل خرطوشة الحبر. رابعاً ، المروحة لا تعمل، وذلك بسبب وحدة التحكم الإلكترونية (مصدر الطاقة). للتحقق من هذه المشاكل وحلها. استخدم منفاخ الهواء ونظف الطابعة جيدًا من الداخل بعمق، تحقق من عدم وجود انحشار للورق، أو وجود قطعة صغيرة من الورق متبقية في الطابعة. إذا كانت كل هذه الأمور على ما يرام، فتحقق من مستشعر نفاد الورق الخاص بالطابعة في بعض الأحيان حيث يعلق ويتسبب في حدوث خطأ وميض باللون البرتقالي. إذا قمت بكل هذه الخطوات، فتتبع اتصال كابل المروحة بوحدة التحكم الإلكترونية (مزود الطاقة) وتحقق منه، وتحقق من عمل المروحة. "Arabic Translated by Google" In HP LaserJet 1300, orange light blinking is a common fault. which is because of different issues. Frist, there is a paper jam inside printer, Second, there is no toner cartridge installed. Third. Toner cartridge is faulty, or printer is not accepting toner cartridge. Forurth, Fan is not working, which is because of ECU (Power Supply). To check and resolve these issues. Use air blower and clean printer well from inside deeply, Check for a paper jam, or small piece of paper left in printer. If all these ok then check printer's paper out sensor some times it stuck and causes orange light blinking fault. If you have done all these then trace fan cable contact on ECU (Power Supply) and verify it, and check fan's working.

شكرا جزيل واتمنى استمرار التعاون والتعرف على حضرتك.انا اعمل معلم واساعد التلاميذ بطباعة الاوراق

It's not only sensor's fault, when fuser sleeve ia not working properly and paper slips it also causes paper jam issue. Secondly when printer pick paper but its pickup time is not accurate it will also cause problem.

Check your scannera data cable / strip especially contacts side which attacha on formattwr board, It came in my observation that its contacts often short.

Use driver setting, set to Econmode printing. It will save your toner and I hope it will solve your problem.

Block No.5, old bus stand, Jauhar Press building, Jauharabad (Khushab)

@@PrinterSurgeon I am from lahore . Ap k pa's aa tu ni skta . Lekin ap ki videos se he smjhny ki koshish Katy hain. JazakAllah

If you need more guidence I can guide you, write to me in details Tce_jbd@yahoo.com

Thanks Keep in touch for more and more valuable and true knowledge.

Thanks for appreciating me Keep in touch for more and more value able knowledge.

بارک اللہ فیہ و جزاءک اللہ خیر Keep in touch for more informative and true knowledge and share as much you can.

Don't worry, you may have installed jumper on wrong place which is CMOS clear/reset jumper. Remove and locate relevant jumper.