Видео

thanks for uploading ...it informative...but want to say....please upload 5 axis multi axis lessons .... because there are so many other channels that already provided 3 axis lessons and tutorials..... so please please make advance 5 axis tutorial that no one willing to provide........

Sooo slow lol

Its amazing how small that E-stop becomes in a time of need!

Are these stock tormach inserts?

puedo hacerla funcionar

saludo pudo hacerla funcionar me estan ofreciendo 2 maquina no funcionan le cortaron todos los cables me gustaria convertirla de analogo a digital

How difficult would it be to turn a UHMWPE spool 3" OD x 2" wide with a 1" arbor? How would I make a center hole for a piece of shafting with a tolerance of 0.2490-0.2495 I need the spool to turn freely, but with zero slop and super smooth? Would a center hole 0.254" in diameter be enough clearance? Any advice would be greatly appreciated. Thank you

Thas sick!

5:54 - "Not sure where it all went" lol

Similar to how I do it (machine flats), but instead I type in mdi a g43 line reading my tool height abs go to z1.0. (I wont rapid to 1.0 and I'll be far from the 5th). I then hand crank flats on material. Measure part. If 2.002, I'll drop g57 z-.001. This method is a 2 wrongs make a right method because you're at the mercy of the tool setter. I'm trying to figure out a better way after I've machined a square up at B0.

Do you have DWO on you post ?

Hi. How to unlock "parameters long word" in OSP5000?

Очень интересно, но ничего непонятно.

smart boy😜

Bu makinenin arıza kodları var mı .benim makina t. 7 arızası veriyor nedeni ne olabilir

😂😂😂😂 oly eate space

Hey Daniel, four years later, how do you feel about the slant 15L? thinking on getting one and would like to know how this video has aged. Thanks!

jesus christ.

Could it be used as a manual pallet setup?

How to check Perpendicularity between slot &tapping visually.

muratic acid works as well. old nitrous racer trick for getting piston material off cylinder walls

Title should be how to throw a 4th axis inside a machine while not giving a shit. I would never throw my hrc210 into my machine like that. Throwing it up on top of the windows ledge slamming it down. You might be able to lift it but it’s too heavy to be placing in the machine by one person or even two. Bring a lift But that’s champions. My machine came in the rain with the foil cover cut away. Had a thin plastic slip over it. Machine was wet. Not soaked but a 1-1/2 hour in the rain from spring to my place with the protective cover cut off of it left a bad taste in my mouth. That and everything just tossed inside the machine enclosure had left me wondering if when I purchase my first 5 axis or y axis in the coming months if I want to trust haas and champions. Even the head office at haas seems to care less. Spent over 130,000 to be treated like just schooled me even more on how not to be with customers.

Very cool, we love to see shops growing and crushing it.

good shit!

Great info. Thanks man. Will be watching.

We should build a coolant proof camera case with one of those mini spinning wheels like the fancy VMCs have to keep the window free of coolant.... I would buy one but I can't seem to find any for sale

Gibbs!

Awesome video! It would be great to get an update review. We have a section on the product page to add reviews as well. Thanks for the support!

I just did a small 30PC run on my desktop machine a EMCO Compact 5 Lathe with the high precision3 jaw chucks O.D. jaws. It was 2.5 diameter and the customer wanted .500 thick x 1.622 dia bore. I quickly learned that HSS SHARP (New) tooling worked best. In fact I used a 2 flute HSS endmill as a boring bar with excellent results. The I.D. was for a press fit bearing which I had no problems holding. UHMW doesn't like heat and you must use SHARP Tooling, the chips can be controlled by interrupted cuts. In this above video the final O.D. and 2 chamfers could have been done on one operation. To avoid the chips balling up near the spindle use the final pass stating at the headstock and travel towards the tailstock. This way the chip will be pushed off the part & you can save an operation. Programming is easier than you think as well.

Hey Daniel. Good to see you guys are still enjoying more growth within your business. Seems to be a common scenario at the moment post covid. Everyone is busier than ever. I'm still working most days trying to keep in front of all the work that's coming in. With this never-ending busier than ever time. I have purchased a new CNC Lathe. My Mazak Mission has be parked until I have time to get back to doing more on it. I haven't really done much else on it since my last video. Hope you are keeping well. All the best with your latest purchase. Peter 👍

Hi Jake, Can you post a link where to get the inserts you use to cut UHMW? Thanks!!

Hows the Tormach still running after these few years? thanks

Where do you buy your mini vise?

i have manual machines would this be ok for a blascksmith starting out or trying to start up?

Thanks for sharing. How are you making the initial cut into the material? I've tried plunging with a 1/4" 4-flute carbide end mill and had it wander and then break on 316L. Trying to mill a flat spot for to drill into If you could share your RPM, cutting diameter, and the depth of cut you start with, that would also be helpful.

You did very well

copy from mastercam of this code ? Thanks

My man. Nice work. Let me help you out with machining/grinding nomenclature. You are using an Arbor on that setup. A mandrel has a taper to lock the workpiece. Many people in this trade get that wrong. I did too. Helps to be taught by old school tool makers. Salute!

Nice! that will make switching bar stock a peice of cake

What depth of cut and feed you use on 3” stainless?

Mark, Just curious to what the actual time was to make that part? Great little video. Thanks for sharing.

Mark, I assume the handle was broken in shipment, did Smithy fix this for you? How undersized was the bore? And, would you purchase from them again? Thanks for sharing.

I'm kinda stressed by you having the vise speed handle in there... haha!

How much does that trunnion weight? This is a excellent trunnion. Do you export?

Congrats! Looks like you have plenty of space for more cool machines!

On my channel I just posted a fix for the failed relays with part # so you don't have to replace the board every time they fail.

Thinking about purchasing this machine for 303SS. What coolant are you using? Thanks for making the video machining SS.

It looks like 45 deg, not 15 deg.