![yonggor](/img/default-banner.jpg)
- Видео 3
- Просмотров 32 358
yonggor
Добавлен 28 ноя 2010
GuliKit KingKong Fix (Teardown, lubricate, fix binding keys)
Ever run into problem with binding key with GuliKit Kingkong controller? This video shows how to open up the controller and add grease to prevent future key binding (sticky button) on this amazing controller.
CHAPTERS:
0:00 Introduction
0:30 Removing back case
2:10 Pry apart the case
6:00 Remove the first PCB
6:45 Remove battery
11:10 Tear down the mechanical switch
15:00 Adding grease
19:00 Reassembly
31:37 How to remove face buttons
32:25 How to clean thumb sticks
CHAPTERS:
0:00 Introduction
0:30 Removing back case
2:10 Pry apart the case
6:00 Remove the first PCB
6:45 Remove battery
11:10 Tear down the mechanical switch
15:00 Adding grease
19:00 Reassembly
31:37 How to remove face buttons
32:25 How to clean thumb sticks
Просмотров: 26 166
Видео
Load cell probe on Ender 3? Bed leveling like a Cr6-Se
Просмотров 6 тыс.3 года назад
I mod my Creality Ender 3 to have nozzle ABL probe like Cr6-Se. This video demonstrates its capabilities and the hardware used. The arduino sketch can be found on github. Visit my github for more info: github.com/sylim5442/Strain-Gauge-Leveling-Probe This is an unfinished project, so If you need more in depth talk about this project, let me know in the comment and I will try to answer in next v...
TPU transmitter gimbal protector
Просмотров 2704 года назад
Flysky fs-i6 / fs-i6s gimbal protector that doesn't fall off. The protector has detent that grabs onto the stick. Printed with TPU98A with Ender 3 Pro www.thingiverse.com/thing:4461080
Thanks for the video. Though, I used Krytox GPL 205 G0 because that is what I have laying around back when I was lubing switches. I assume this would work better since Gulikit switches kinda act like mechanical keyboards. If you have Krytox, use that. If not, use bearing grease as it's much cheaper.
I didn't have bearing grease on hand so I used krytox (the one to lube keyboard switches) and it worked just fine too. Thanks for the video mate.
Thanks for making this vid. I ordered this controller and will be switching the face buttons to the Xbox style as soon as possible. I do worry about that metal plate sorting the soldering though. Sounds risky for a controller that's almost $50 Canadian.
Ya I did made the mistake not taking enough precaution for the potential electrical short. It's better to remove battery and discharge capacitors before fiddling with that metal plate.
what was that nifty lil gadget you used to take the screws out?
That is Xiaomi Mijia electric screwdriver ! Good quality tool for its price.
Thank you sir, God bless you.
thanks
Thanks for the steps. My controller's right joystick was getting stuck, and this video was very helpful with opening up controller. To finish the job, I did need to find another video, but the initial steps with the same. Please continue making videos like this.
Can you please share the link for the other video?
thanks
U made thanking this controller apart look east as can be either that isn’t thr first time u have opened it or the made the kk3 max a lot harder to open. I have issues with the back buttons giving out after like no time at all.
Can you pls do a tutorial how to change joy stick in the gulikit King Kong 2
My X button (top) is constantly coming off just by pressing it with a little more enthusiasm. I emailed them and they suggested I put some glue on it (wtf?). What would you recommend to fix this?
Wedge a tiny piece of toilet paper between the cap and the pushbutton. Try a few times or change the paper to something else (plastic bag, cringe wrap, receipt paper) until it stop falling out again.
@@yonggor thanks for the advice!
Thanks tons for this video, it was nice not being yelled at with EDM being thrust down my ear canals and gigantic bell icons chasing me in my nightmares. I get really stressy doing this kind of stuff cuz over time I've developed a knack for conjuring ways to screw these things up so having a straight up video to come to is really nice. I was in the middle of goofing around in ToTK when somehow I couldn't jump anymore which sucks when you've got a sword approaching your prefrontal cortex at mach 6. Kicked this on, took it apart, and lo and behold our good friend dust. Cleaned it out, put it back together and it's all good to go. PS for anyone else; the bumpers may get stuck behind the triggers if the case isn't on cuz there's little plastic lips in the backplate that help move them out of the way ever so slightly.
thank you
Welcome!
My king kong 3 broke my pry tool. I put the wrong A button in the wrong slot and it's stuck. I literally just opened it.
thanks a lot, i didnt know mine using switch button placement so i accidently put the wrong button placement and it was stuck there, your gluestack tricks helps alot
4:30 why do I hear a man moaning?
I wish I watched this video before I grabbed my hammer when my kk3 max right thumb stick snapped in half
literally was planning on doing this to my ender 3 s1 glad to know Im not the only one that wants to do ridiculous things to their ender
Hi my friend, my King Kong 2 slipped out from my son's hand, and completely died on the impact. I've followed your guide, to see if there's anything off, but I couldn't find any issue, visually at least. Woud you make a eletronic video guide, to test continuity, voltage, current, etc.
I only needed to open it cause I had a loose piece so Thx a lot this helped a lot
Didn't realized you can remove the thumbstick, i don't think mine can do it. Should i put some twist on it?
nevermind, i can remove it. Thanks!
Hello i want to ask some question my zr button can't be use it fell down twice what i need to do and it makes squeaky sound
3:21 are those weights in the controller?
You are right.
Why my Gulikit KK2 usb c socket wiggling (not firm)? 😭 is it just me or anyone got the same problem?
ive got a weird bug with mine. the '+' and '-' -Buttons get registered as being pressed at the same time even when im pressing only one of them. i tried updating the new firmware but it didnt help. not sure if its hardware related. only got it for a week...
Mine is doing the same thing after some month of use, its driving me crazy
@@Manuel-px4qw glad im not the only one...
Its the worst controller Ihave ever had, upgrade bricked it straight away, this was my7 experiance, why dont they have any soft ffs its 2024
why does my L2 block my L1 after reassemble ? where did i go wrong ?
I had the same problem. Just close the control and they will work normally.
@@mslucasmelo im not sure about your however mine are fixed just by putting all the part together and it will fit just right.
I wanted to check this video out to see if you knew how to fix the squeaky trigger problem but you sure did fix the button delay problem💯
When I did mine I used white lithium grease🙂
Thank you for the time and ditailed explanation! It Helped a lot!
👍
Can you change the button layout to xbox? I hate switch layout it’s confusing for steam player
You need to buy the xbox layout buttons instead which gulikit do sell. If you try swapping the current buttons it won't be flush due to the difference depth of the switches.
Thanks for this vid op. The B button on my controller started to squeak aswell and it drives me crazy with the noise it makes. Did the lube by using the krytox grease as most here mentioned and so far cross fingers, no more squeaky noise. 🎉 It's a bit of a shame that people had to do this mod because the controller is really nice. It feels a bit better than your regular xbox one controller. The disassembly btw is not too difficult, but for newbies it's understandable that it can get a little tricky once you have to gut the whole thing out. I recommend double or triple check the vid if you have any doubt.
Great. Thank you for your feedback!
One of the most user friendly controllers to fix, pretty strait forward, don't get me started on PS controllers🤬
Do I have to use grease because I don't have any
orang indo bang?
Org Malaysia bang
Much better if you put Krytox 205g0 to mech switch
Hi man my left analog making noises when i move it, do yo think it's okay if i lubed my analog with electrical grease
Analog shouldn't squeaks! You should open it up abd check if the stick got any imperfection underneath.
I have stick drift😡 I thought they said this controller was stick proof Is the first week of buying
try update the firmware, you can find them from official website. Some firmware versions are faulty and your controller might be one of them.
Your video is very helpful, Many Thanks.
You are welcome!
Hi i have problem with my RB trigger button. it's responsive but you have to press it harder than usual. is there anyway to fix it?
I just rotate one part in the switch 90 degree sonthe face button now become linear switch. I prefer linear switch than clicky one, less maintenance to do..
I tried that too! Went back to normal clicky button because of double pressing.
Are the ABXY buttons swappable? Can I just take them out and reassemble them like an xbox controller?
cannot, AB and XY buttons have different lengths, so you cannot just swap them. However, Gulikit sells xbox style replacement buttons.
good video. my new controller got squeaky B now greased and it's gone. tqvm.
You're welcome!
Thanks for the vid, I had a button squeaking on day one but loosening the clips slightly seems to have fixed it
Glad it helped
Whats a "clip"?
@@shahariarmahmud5218On the side of the button,theres a little tab.Those are the culprits on why the buttons squeak.Theyre made a little bit too tight
@@shahariarmahmud5218 might be a super late reply, but I just got mine today and had the same problem. in the video at 11:13 you could see him rotating the switch to its side showing a rectangular "clip/flap". I inserted a small flat head under the clip to bent it slightly outward and that fixed the bind. Will definately grease it later once I got my grease.
someone in the background having a seizure
😂
my left trigger feels like shit, like its scraping against the housing or something.
Try removing the back plate, scrape should have marks, try to make room for it with sandpaper, removing some tenths of mm :) Or maybe the trigger has some cuttable casting spills :o (Was meant to say, probably manufacturing = QC defect, not by design.)
do you have a fix for this? I have this one also @yonggor
Update: it seems that if you put in the case screwdrivers, the trigger will go back to normal. That was the solution for me.
When I hear that kind of music from the Middle East it scares me.
Don't worry. The controller is made in China, it's not going to explode...!
@@yonggor No the music from middle east scares me, because I know how radical the people on those countries are.
its not fix, its lube hahaha , but i will try and thanks for making this video broo
i don't know what i'm doing wrong but when i reassemble it, my right bumper feels mushier than my left one. I've tried multiple times reseating the 2nd pcb to make it even, but so far, no success.
yes, a lot of people face this problem. Maybe I should do another video to cover this problem...
Me too i just kinda accepted it
You messed up the gamepad, man. :(
just asked my gamepad, she is better than ever
@@yonggor Ask your gamepad in two years, let's see what it will answer you.
Nah, nothing will happen, worst scenario will be that you have to swap out the switches if it's starts to crap out. Gulikit btw sell their switches too if you needed one.
@@afiq358 The best option would be to use silicone grease or a fairy tale for mechanical keyboards. And this one will eventually corrode plastic and rubber, because both are made of oil in fact. I don't think there's any need to argue with that, it's just a fact.
I ordered mine and had the problems with buttons sticking down. So immediately I got to work stuffing it back into the box, putting some tape on the box, requested a refund and ordered an 8bitdo which has functioned perfectly lol
😂😂😂