Видео

How I can get this product Dupli Color in India?

Thanks for the video.

61,404????????????

If I go to Napa, O’Reilly’s, Autozone, (wherever) and ask for an actuator, are they going to know what I’m talking about or look at me like I just talked in some kind of gibberish?

Where i can find

Do not try using brush to brush paint along surface, just dab it. Lightly wet sand paint after it dries using a flat block. Go very lightly as not to take too much off. Use 2000 grit. Clean off dust, then dab the clear coat on lightly. Do not brush stroke it. Wait 24 hours, then lightly wet sand with 2000, then 3000. Clean and polish with light compound. Apply wax after all the light sanding marks are gone.

I watched all the way through the video. The calibration method could be used at the start as part of trouble shooting. After I watched the video I ran the calibration. This is all I needed to fix mine.

Nicely done

One down. 50 more to go >.< Thank you and God bless. im definitely picking one of these up if I see one

Brialliant WJD well done fab instructional video , from west of London UK. Graham [ Chartered Engineer ] 👏👏👏🎬.

Excellent Brother!!! I'm doing this soon, and replacing the door threshold also... Thank You Much Chuck in Michigan

Yeah, I’m not a big female so I was able to hang upside down and change it😂. Also, I use a battery and a mini clamp to angle the shaft. That way I didn’t have to use the ignition. I found the idea on a RUclips video here.

Is that paint durable?

Good one, thank you

Was looking this up before applying to my 03 impala, small world.

ive replaced the 2 easy ones in my 09 in the past couple years; one being this summer... and now ive got not a clicking noise but more of a water pump noise coming from behind that dash.. absolutely been loving this car for a good 8+ years.. and the clicking noise has been my ONLY issue! luckily they were easy cheap fixes from a friend of a friend for ~100$

I want to try this, but when my negative cable is disconnected, I can't remove my key from the ignition; it gets stuck in the accessory position. Any idea on how to get around this?

Name of the product, plis mister 🙏🏻

Thank you! My brother had this problem for YEARS and now we know.

I'm getting ready to do this. Thank you.

It is just the actuator going bad eventually? It sucks that you have to replace it.

Ху..ета американская

Are all 3 actuators the same style ?

good job , Thanks for the info

Thank you So much for doing this video. My door has the same rot and I was told the entire door and frame have to be replaced. Now that I see what you have done, I will repair my door frame the same way and save money.

So all the actuators are the same or right

I also did this, and it left a mess on my chassis

how the hell is that thing so clean under there, if i ever dare to attempt removing the manifold heatshield bolts on my it would take HOURS and an oxyacetylene torch you guys in the south of the US have it too good man, meanwhile i have to fuck around with a torch cause i'm in canada

That's a really nice Impala!

Help. What do you call the vertical wood piece (4:11, right side of finger) that is also rotted? Got that & under my windows (plastic siding, insulation foam, rotted wood). Don't know what that wood panel called to look up.

you did not show step by step>like you said> no videos out there for us:(

2024 and they still can't come up with something better than this. No wonder aliens do not come here. Humans are dumb.

*I watched this video and ended up ordering 3 of them. Easy install, no more AK47 gun sounds* 😅

Can you get this at local auto part stores or online ?

Out of curiosity how long did it take you to do this job?

First time I heard this noise is when I open up my car door and I didn't get a chance to get in it yet

This video has no information on the type of vehicle!!!

Perfect video for my situation. I"ve got the same type paint pen exactly from the Chevy dealer and need to take care of some chips on the dually fenders. Thanks for posting this

DRY TIME till polish.????

I heard those teeth break off.

Hey could you elaborate on the start up? 1. Start engine without holding brake 2. Hold the brake and gas fully down 3. Press engine start button for 2 seconds then release brake and gas? I tried and it turned the truck on and it redlined right away haha.

i did this and messed my car up so bad💀💀 i only recommend for rock chips

I got the pin but I don't have a rubbing compound. What is this? Where do I get it?

I have an Impala I know several people who also have an Impala this is a very common problem. I know this occurs after a few years in use but by now you would think they would improve this problem!

Thank you friend I did passenger side both about year ago got in yesterday and that god awful clicking but on driver's side thought oh boy here we go again thank you for taking the time to show and explain as I'm a hand on learner I found after watching you do this I surely can do ordered the part made sure it was the one and yes can feel the darn thing clicking it stops after about 5 minutes it don't continuously yet but I'm sure if I don't get the new one in continuous will be next 😢.So I'll update you when I get part and install it tueday. . Thanks again 👍😊👍.

I’m wondering if the brick molding board being of pvc is enough with it being the outer piece of board and more exposed to sun and rain is it not an issue I have to worry about in using the treated pine jamb board in the cut out sections you do at the bottom on both sides? I have looked everywhere for a pvc material jamb leg and can’t find it anywhere. Only if I’m willing to buy a whole doorframe kit which I don’t want to do. Is that treated pine holding up well?

That shit don't work !

Did you have code p0843?

The door jamb you used says treated pine. Could you have cut out the old wood section you cut out at the bottom and then used a jamb made of pvc instead?

Thanks