Видео

Holding your breathe while doing such a small job 😂 all the grunting annoying

I bought a BLACK ANODIZED ALUMINUM EDELBROCK FUEL FILTER, looks and works GREAT!!

I see you have Scott Performance on your bike! 😅

Was wondering if you know the part number for the tear drop s&s filter unit as I want to get one for my 2009 street bob

I did mine yesterday on our Coachmen Catalina RV. I have to say, I was amazed at how much the old grease had broken down from the last time I did this. It was like 40 weight oil coming out. I'm glad I did this. We are getting ready to take a cross country trip in our RV and I could almost bet if I hadn't lubed my bearings, I would of had a problem somewhere with a burned up bearing. I have done my wheel bearings using the Dexter E-Z lube system and never had an issue with a rear sealing blowing out. I think some people don't take their time and keep pumping and pumping grease and not turning the wheel. I take my time and like I said, I've never had a problem. So glad I did mine before this long trip we are about to take. Nice video and very clear. Thank you for posting!!

And unlike a unreliable motorcycle, you don't have too be constantly tuning the carb or mixing oil/gas, changing out spark plugs, adjusting throttle and clutch levers. you know your bike will just work.

What did you use as a catch can?

Good Job on that setup, Where did the 90° breather caps come from ? Been wanting to do this mod for awhile now but didn't want the hoses coming straight out of the head. Thanks in advance

Hows about just running a 1/4" steel tube under your rear fender, (to the end), and running a line from the "T" fitting to it? Done this PCV method for decades with great success, "NO MORE RESIDUAL OIL ON YOUR REAR TIRE OR YOUR ENGINE!"

Visit my website for all the Amsoil products you need, shipped right to your door. Thanks! www.lexcosynthetics.com

HI, what size was that brass t fitting you used? Cheer's.

Cuz oys too.easy.

Forget a catch can. T or y fitting and run the hose down behind the oil pump and under to the bottom frame and call it a day! 6 feet of hose and a fitting DONE

$40??? Here in Australia, they usually cost around $100 dollars more than that.

Were is the parts list. What size hose ? 1/3 1/ 3/8. Wish I knew

I did my 07 softail last year and I vented to atmosphere , it made a nice difference and the filter last much better , great video , to the point and simple

Amazon sells those spring type clamps in metric sizes... I hate those screw clamps...

Not a bad idea for sure but the worm drive clamps look janky- the constant tension clamps(at least where visible) would've looked much cleaner, besides i doubt they need to be all that tight.

Hey Blinker, hows that catch can catching fumes? Have u made any mods to make it better, or is it good as is? Just found ur channel. 👍

Why not just drill two holes on one side of the filter to allow it to breathe and just run the 2 hoses into the catchcan/gas filter ,one on each end ?

Have you been watching too many detailing videos and wanted to give it a shot yourself? Because if so I’m in the same boat, my interior has never looked better lol

I'll done the same thing but it still comes out the holes i drilled to vent and goes on exhaust on 2014 street glide

Little bit of steel wool at the bottom of can works well. I have DIY catch cans on all my vehicles and they catch a ton of blow by. I used to have one on my Dyna but I removed it and now just vent to the atmosphere because the hose from the front kept getting clogged. It worried me that the pulses from front and rear feeding to the T fitting were fighting against eachother causing the front to get clogged and rear to drain. So I decided to vent to atmosphere and it works great. Not that much even comes out and I just have a little rag I wipe it with occasionally, never gets on my leg, pipes or bags so I’m rockin it like that. I filled the factory holes inside the throttle body with black silicone and smoothed off so air doesn’t get trapped in the little holes for most efficient air flow.

For securing the hose clamps I use a socket with an adapter to my multi tip screwdriver....NO scratches on the tank. Great idea for catch can.

I made a similar one for my 2013 Road Glide, 2 holes are plenty for it to breathe, I have 4 holes in my cap too, so I'm gonna put another cap on mine with only 2 holes drilled into it. I have to clean between my lifter blocks a couple of time a week so I'm gonna put a fuel filter in my catch can to see how that'll work. Thanks.

Better than a greasy right leg. Like the idea, dig the look.

How's that working out for you? Is it effective? Why not leave the filter in place? I like the idea!

Here's a comment to help a little getting started lol 👍👍

?