- Видео 5
- Просмотров 73 775
The Layman Life
Добавлен 14 янв 2019
How to install riding mower tire tube
In this video I show you how to unseat a riding mower tire, remove from wheel, install tube, and reinstall. hope you guys enjoy the video and be sure to like and subscribe.
Просмотров: 543
Видео
Removing the governor out of a Predator engine. FAST SPEED
Просмотров 1 тыс.2 года назад
Today we removed the governor out of a predator 212 to allow us to reach higher rpms out of the engine, we originally started with 33-35 mph and after removing the governor we gained about a 10mph increase. does removing the governor decrease engine life? YES! Does it make driving more dangerous and more fun? YES! Like and subscribe losers.
Mower shaking while running? Here's something to check and possibly fix
Просмотров 1832 года назад
Got an older snapper push mower that had run over something causing some damage to the mower frame, watch this video to see a possible fix for you if you are having the same problem.
Coleman mini bike not starting/only running with choke? here's something to check.
Просмотров 72 тыс.3 года назад
Today we have a Coleman CT200U-EX mini bike that does not want to start up at all. Pulled the carburetor off and gave it a nice cleaning, put it all back together and it fired right up! hopefully if your bike isn't starting up or only running with the choke this works for you. Thanks for watching!
Quick question so I replaced the carburetor on a Coleman minibike 200c & it runs fine but when I full throttle after a few mins it just turns off any ideas what I could do?
same with mine it like starts bogging
I have this problem I sure thank people like you ❤
I’ve cleaned the jets and clean the whole carb but my bike only runs when the choke is on and as soon as I take it off choke it turns off
Sounds like something is still going on with fuel supply. I would also make sure there's nothing in the fuel hose preventing gas from flowing correctly. If worse comes to worse buy a carburetor off amazon for like 30 bucks. I'd still check the carb again and make sure there's nothing small blocking up the jets.
Hey help me. the bike was running fine then i put 91 gas in it and now it wont start up at all. i drained the gas and put 87 gas in it and cleaned the carb and checked the spark plug. all of these things are correct but still it wont start
Does the engine have compression? It could possibly have burned rings but that doesn't seem likely. I would spray some starting fluid into the intake and see if it fires up. That'll rule out if the motor is blown and if it has spark.
Did you clean the pins too
Yea I normally try to clean everything when it's all apart. Normally can throw everything in an ultrasonic and it gets it all cleaned up.
Seems common with these little bikes(carb running w/choke)🤔
Mines has a different carb but I’ll try it and let you guys know if it works
Hey, did it work for you?
Why does my bike drives off when I started?
Sounds like idle screw turned up too much. Causing it to rev up when started. If you loosen it some it'll lower the idle.
I had the same problem. Found the carburetor loose. Went to tighten up the bolts a little and found that the boats were stripped out now I'm having trouble finding the studs. Anyone know where I can order them?
this world like a charm for me! I was sure it was going to need more than just this because it was running so badly but it was just a clogged jet in the carburetor. using compressed air along with carb cleaner and just spending 10 minutes spraying and blowing will result in a perfect running machine again. and if not just buy another carb they are cheap.
Yea, the carbs they have on Amazon are crazy cheap! I'm an impatient person, tho so when I want to ride it, I want to ride it right then. I'm glad I was able to help!
3:26 when you said that you blew the jets out did you take them out or did you leave them in and air compress it
If you really wanna clean it you can pull them out and clean them using a small flat head. I normally just blow some air into the carb depending on how bad it is.
Great job! You were very good at just keeping on facts and points needed to perform job. You are a real pro and make it looks easy however, you have great experience and it shows.
I'm glad to hear that! Thanks for the comment!
Ey dude I’m kinda worried got the ct200u predator 212 it’s a pretty new motor I maintain it well but have made some dumb mistakes and hope no damage was done like I had it on its side for a few minutes then when I started it tons of smoke came out of my straight pipe exhaust and was leaking something it was kinda weird also had a bit too much oil in the bike a couple times but now it’s good bike seems to be running good still
Thats normal just dont keep it on its side too much because the oil will leak out the carb and that white smoke is the oil getting burnt up
I’m having a random Throddle issue on my ct200u engine is brand new the Throddle just worked perfect a couple days ago it’ll twist but will get stuck a little and not return great everything is hooked up correctly
Those springs that they have for the return aren't very well made. I would take a look at that and maybe see if you need to clean it off or replace it.
Please help,purched this bike beginning of 2022 for grandson he rode it about 5 times ,everything was fine then this summer when he starts it it wants to take off seems to be throttled up and also when you release throttle its still idleing high not allowing brakes to stop well.
Sounds like a bad clutch. Try replacing it and see if it changes. Hope this helps
Wow that’s amazing 😮
Mine runs only when applying the throttle but if i dont it dies, i smell lots of fuel so its running rich but cant keep running on idle. Are these symptoms of dirty carb?
Same problem
What do u recommend doing to make my ct200u go at least 35-40 mph with the jack shaft ?
I'd probably rip the governor off or put a smaller sprocket on the rear shaft
@@thelaymanlife8591 u mean the sprocket to the tire ? And also If I were to put the straight chain back on is there a clutch that is made for that? Or is there something I can do to make the clutch last longer ?
@@troyholland3436 You got insta? Follow me and send some pics of what you're talking about. It's Conner Layman
Any ideas for mine? Doesn’t start, put new oil, gas, and carb in it. Oil leaks through exhaust pipe.
if you have oil leaking thru your exaust pipe then it may be that it sat on its side by accident , if you lay these on their sides and leave them that way oil runs into the combustion chamber and then they will not run, I had it happen before where it was so full of oil in the cylinder I couldn't even pull the pull cord and turn the engine over. best thing to do for this is take the spark plug out and use a shop vac to suck the oil out of there, once you can get it started it will smoke real bad for a while as it burns off the oil that go in where it shouldn't have. if it is not from laying it on its side and you have oil coming out your exhaust then the other thing that could be wrong is a cracked engine block or bad seals, if that is the case you may as well just get a new engine for it, they are not very expensive and the old one can be used still for parts.
It’s your spark plug wire. I just changed mine.
Mine keep dying on iddle and it wont start again
Mines have a intake but idk… same problem… Wheels get stuck when it doesnt work too
Any ideas for mine? Starts with choke, take off choke and stays on, when I try to run, bugs out and hard to restart. Gas is fresh, even changed the carb. Anything will help. Thanks
Make sure it's got good spark. And check and make sure you've got good gas flow going to the carb
Hey man I removed my governor 3 days ago and the bike would start but every time I gave it throttle it died. I gave it some engine starter and it worked but now the bike doesn’t even idle and the new Coleman carbs don’t have an idle screw. I’ve looked everywhere and I have no clue what the problem could be.
Removing the governor on those is tricky. You need to put a spring to make sure it drops back to idle. I have a video on doing the governor.
Mine is having an issue where it idols just fine but when I throttle it it dies almost immediately. Sometimes when I throttle, it bogs down like it’s trying to get going but eventually just dies. Any advice?
Mine too and my gram broke at the 2 front welds
@@KD-ts6xr I took mine apart this morning and it seems the problem was the pilot jet was gunked up. Cleaned it and put new fuel in it and so far runs great.
I would clean the carb and check the spark plug.
@@Joutlaw29same my engine smokes when runing and doesn’t let me throttle it at all just revs but the jet was shredded some how and fucked the carb up idk could be the problem better carb?!
"""" ANY OF U GETTING A MINIBIKE OR GO KART, IF U WANNA HAVE TROUBLE FREE CARBURATER FOR YEARS THEN ONLY ONLY RUN NON ETHANOL GASOLINE!!!
why would you run any other gas 😭
@@Coleman43 u be surprised how most people don't know about running only non ethanol gas in small engine bikes
@@johnhancock2914I didn’t know I just got mine a few weeks ago and wish I woulda known this
What gas stations sell ethanol free gas?
@@kerrygatling663 QT
Mine won't start I have trouble shooted everything please help
Thank you it works
I know It might not seem like it’s doing a lot when you’re taking it apart and cleaning it but i assure you it’s doing more than you think I just did the same exact thing to mine and it started right up on the first pull
Glad to hear that bro!!!
I need help I have a 2 stroke engine and when I stop it cuts off and it takes a long time to start back again
What year is the bike?
@@thelaymanlife8591 I have a gas scooter
@@Matthew-fl6vu I'd check the carburetor and make sure nothing is clogged.
@@thelaymanlife8591 ok thank you
very helpful 5 stars
That’s a 6.5 hp engine lol
Thanks for telling me?
@@thelaymanlife8591 Yw but I got a hella project I just finished with the 212 and it hits every bit of 40 mph
They won’t start if you have the air filter off… that happened to me, I put it back on and it fired right up
ruclips.net/video/TYp7SgO_FrU/видео.html
How much of a life decrease does this make
It really depends how you ride it! The biggest problem you'll probably run into is bending the push rods.
Does it affect timing?
No it will not! All the governor does it keep the engine revving up past a certain amount of rpms
Very cool
Very cool
Thank you sir
Um what was said at 5:36 Very unprofessional
We will have him taken care of
Nice!! Looks good!!
My too only run on choke
So guys, update on the coleman mini bike, me and my friend both owned one and removed the governor out of both. A couple months with riding it like that they both seemed to stop working. I believe the higher rpms caused the engine to lose compression which caused it to stop running right. I've heard some people say it's better to buy the predator engine because it can handle the higher rpms better.
What some people say is just speculation. If you abuse any engine it's going to break or wear out much sooner than it should. The Predator isn't some magical all powerful unbreakable engine that some make it out to be. I will never get a Predator 212. There's just too many better options out there including the new Pred 224.
Going to upgrade mine and pulling the governor is one thing I plan on doing what you can do to counter the high RPMs is to put stiffer valve springs in it. Could have burnt up the motor maybe another issue or your piston and your valves may have been playing a little bit of patty cake. Either way these motors are cheap and a dime a dozen and there are parts a plenty so I'm going to do all kinds of stuff to mine and see what I can get out of it. Also if you want to get a little bit more speed out of it I heard the belt drive is a good replacement for the clutch. So many options lol
And have you checked the spark plug?
yeah I think it burns the valves when you run too high RPM on them. personally I dont care to go faster than the 20 mph they do stock because they have no suspension and are not very stable at higher speeds , if I want to go fast I would just get a real dirt bike, these little bikes are fun for around campsites and putting around in the neighborhood.
You just saved my life subscribed
I’m having an issue when I start riding it it feels kinda deleyed and it just randomly turns off somethimes
Ever figure it out?
@@antoniorojas3154 ye It was just the spark the whole time just take off the spark clean or get a new one.I got a new know it works great
@@MrXLOL-nm7bw what spark plug did you get? Im having a hard time finding a replacement in town.
@@MrManVR179 ask an employee or go to Walmart and ask for some spark plugs and ask them wich one is for the bike or go to an store for stuff like that and ask them and show them the previous spark plug that came with it and if they don’t have it search up the model online and order it
My minibike only runs when I keep pressing the throttle it won’t sit there and idle Any suggestions
Adjust the idle screw
@@Mista_Js_wonderful_toys how
@@alexdawgk6142 I took off the air filter then you will see this spring under the gas can, what I did was take out the part where the screw connects on the left and that fixed the idea issue not the other
I have a problem rn..it was running just fine then I gave it a wash with the hose and washed every part of the bike..and now it just won’t start..
I would check to see if you got water in the gas tank, it doesn't seal very well. I would drain the gas the pull the carb and clean it.
Hey so I have the same bike it starts but won’t move in gear? How do I fix it
I would check to see if the chain is attached. Make sure all the gears are hooked up correctly and nothing it freely spinning.
When I start mine it makes a weird noise and when I crank the gas it doesn’t do anything but make more noise and goes nowhere
I would check to see if your clutch is attached. Sounds like it's something with the drive system.
can u make a vid on how you removed the governer?
Hey, I'd love to! I currently am super busy with my job but I'll make one when I have the time
alright thank you! also what did you use to plug up the fuel line?
@@letsgogo8473 I just shoved a hole punch in it lol, you can really use anything if it's nice and tight 😉
@@thelaymanlife8591 lmao alright thank you and was the way you took out the governer hard?
@@letsgogo8473 Honestly it was that hard. The hardest part was removing the c clip that held the governor on the inside, I'd watch cars and cameras, they've got a video on how to do it as well as red beards garage.
I bought mine off Amazon back in April it started but never ran, today is the 1st time I’ve rode it since I had but it keeeps stopping after Rodin for like 2 blocks. I have no idea what to do
Sounds like you have a fuel issue, I would check the fuel lines and the float in the carburetor. Also check the jets.
I had the same problem it was my gas cap
@@osamarodriguez6673 How did the gas cap cause it to not run right?
@@thelaymanlife8591 there Is a small hole on the gas cap the rubber under the cap was not put on rite so it was getting air so it kept shutting off I adjusted the rubber under the cap been running good for 3 months now
@@osamarodriguez6673 Awesome! Thanks for that info!!