Видео

B2😀

@SequreTech thanks

Please check the S60P which is compatible with the C210.

Dear customer, you can refer to the tutorial and document in this link: sequremall.com/blogs/odesc-tutorial. If it still doesn't work, please shoot a video and send it to us by email. info@sequremall.com

This happened to me i needed to enter "dump_errors(odrv0)" to get the errors

aliexpress.ru/store/912407184 Please check

🌹Thank you very much for your recognition of SEQURE products.

Thanks

Ordered. If everything goes well with my test set. Probably going to be picking up a few sets to sell to the local guys

Dear customer, you can refer to the tutorial and document in this link: sequremall.com/blogs/odesc-tutorial. If it still doesn't work, please shoot a video and send it to us by email. info@sequremall.com

@@SequreTech I have run through that tutorial several times with multiple Flipsky 7070 motors and multiple Odesc 3.6 boards. Motor calibration almost always fails with errors like unable to read phase current. Both motors work fine with the FSESC 75200.

@@lusher00 Dear customer, please shoot a video and send it to us by email. info@sequremall.com

Yes, stay tuned for the release of the escape 32 version and the corresponding climbing motor soon.

@@SequreTech I have mine flashed to escape32 and with WiFi link We are currently waiting on new boards right now. There are dual mode sensored non sensored

@@jdmtyteeeyo yes,good.

Thanks for your comment. 291g

@@SequreTech Thank you. Mine weighs 275g. Then I found out that this block has two completely identical models. The only difference is that one weighs 290g (it works with 2.5ohm tips) and the other weighs 270g (it doesn’t work with 2.5ohm tips). You'll have to look for a block with the required weight(

@@7Lucky7Man7 Regarding the question you mentioned. Could you show it with a video? And send it to our email: info@sequremall.com

@@SequreTech I haven’t had time to check it myself yet, since my sting hasn’t arrived yet. I read the information from the 4pda forum. When I try it myself, I’ll write you an email.

Thanks for your thoughts, that's a good suggestion. You can follow us and you will see this product in the near future.

@@SequreTech Thanks

Hello Dear, you can check via this link: sequremall.com/blogs/sequre-product-firmware-upgrade

Hello Sir, ES126 is currently discontinued. You can pay attention to our new screwdrivers ES666 and ES555

@@SequreTech Failing to support your product by not providing firmware on request, and attempting to force the user to buy ANOTHER product they don’t want, is poor service, and absolutely appalling.

Hello, is it to add the physical button of the power switch? This will add volume.

Thanks for your comment. 135W is the rated power of the power supply, and the instantaneous peak power can reach 160W.

135w is output power. They are measuring AC input power which will be 150w for 135w out at 90% efficiency.

Connect the positive and negative terminals, the maximum voltage is 21V, if using 2.5Ω tip, the maximum current is about 10A.

If you’re getting a variable power supply and intend to run it right at 21V, you’ll need 7.4 amps to hit 150W. In the video you can see it will actually hit over 160W with some tips. So assuming you’re using a 24V power supply with a regulator, an 8A power supply (180W) would be the absolute minimum you want to get. I’d probably look for a 24V 10A (240W) power supply to be safe. Then you could couple it with a DPS5020 regulator which can handle the voltage and current the iron will need at full power to bring the voltage down to 21V. Or just use a 5S LiPo or LiIon pack. Even with a 4S pack you’ll still get 90W at nominal voltage and 115W when it’s fully charged, which is plenty for just about anything you’d do with this as long as you’re using the right tip for the job. And unless you get a teeny tiny pack, it’ll for sure be able to put out 8A peak current.

@@swissfreek thanks a lot! Do you know, is it some ic in this cable xt60 to type c? Or I can made it by myself just connect + to +, and - to -.

@@andreykvv There is no IC in the XT60 to C cable. Just need to connect the power "+" and "-" correctly. Please note that there is a risk of damaging the product if the connection is reversed.

This is not recommended.

There is an XT60 to C power cord in the package. You can connect the power supply to the XT60.

@@SequreTech can I order it separately?

@@andreykvv Yes, if you can't find it on the website, you can contact customer service.

Yes, still used drv8301

@@SequreTech it posible to coustem it wothout drv??

@@botak333 Hello, need a drive.

@@SequreTech yess sir, i want make coustem odesc single motor bur without DRV8301, i want to used ir2101 same LIN and HIN input, so the odesc can handle more than 75V sir. It posible or need to coustem frimeware??

@@botak333 Replace the component with one that can withstand higher pressure.

ES666 has a greater improvement in electronic torque than ES126.

No-load Speed: 250rpm

You can purchase via this link: sequremall.com/products/electric-screwdriver

The default shipment is that the soldering iron head is 5.5 ohms, and the electrical source you described can work properly.

Yes, this is normal, as the maximum power of the S60 is not recommended to exceed 60W. Generally, 11V can reach 60W without limiting the power, and when the voltage is greater than 11V, the soldering iron will start the protection function to reduce the power, so that the maximum power is controlled near 60W.

@@SequreTech 60W of power is enough for me, but unfortunately I was only able to get 40W. But I need to clarify that I used a 65W noname power supply and perhaps it does not provide the declared power. I will once again check the operation of the soldering iron with a good power supply from Ugreen 65w.

@@sergiydy2820 It is recommended that you set PPS in the menu to see whether the power source meets the protocol and whether it works normally. It depends on the type of power source.

Его можно найти на нашем сайте, но вы должны снабдить его достаточным количеством энергии.

Using original Chinese may be most users can only read subtitles, so use the system voice English.😭

Yes, you can download it from the tutorial on the website.

@@SequreTech sorry there is nothing on your website as far as tutorial Could you please provide link. It would help bunch of people out.

@@nsdo72 I couldnt find a link to it from the product page. I was able to google "odesc 4.2 pdf" and i was able to find a little blog thing on the website with all the files.

I cannot download it too where is the file?