Видео

I know this video is 6yrs old, so perhaps it's dated. It's a shame you can't buy this ImmersionRC RF Power Meter ANYWHERE now. (Even eBay !)

is it possible that the pin assignment on the jack connector is reversed in taranis x9d? not working for me...

I shoulda looped it…..

is this unit referenced with -30db attenuator as the norm / from scratch? I'm seeing like -25dBm without any load on these V2 immersion RC I'm getting more like -60dBm on my el-cheapo USB3 RF power meter and its display without any offset or attenuator on it. I'm a newbie into this, so very likely me that are misunderstanding something..

Hi there, I know this is an old review of the RF meter, however, What Attenuator would one need to test over 1w for RC application please?

Wow! 6 years ago his was my little baby!

Wondering if this will work on the Taranis QX7 ?

I've got RF meters, more interested in that other kewl gizmo, a programmable Freq Generator??, w/ a wireless remote fob?? button pushing does what?, loads the parameters you set on it?? Very nice bench tool ;)

Pls zoom in with the camera and have it on a stable mount. Thanks for making this vid!!!

Thanks mate!

Saved me a lot of time!

My attitude v4 was ppm5 and ppm6 by default. For such an expensive set of goggles you would expect osd for these options but sadly it's some random button combo to change the settings.

what are the ppm numbers on the 9xr mixer anyway? are they "extra channels"? i use ppm7 and ppm8 for my headtracker, which works. but if i unplug the 3.5mm jack from the 9xr, the pan and tilt servos go crazy. ???

Nope, 6dB doubles the audio presure level. In RF, 3dB doubles the power level.

Thanks man, I got myself twisted in knots trying to do this after programming the flight modes lol.

Hello! Where to buy such a table with racks like you?)

Power doubles every 3 dB.

Great video. I have shared it at globerc.com/product/banggoodcom-immersionrc-rf-power-meter-v2-w-integrated-8-hour-battery-for-rc-drone Cheers!!

Your instructure is L " Using Arduino Nano you can create a BLheli USB linker and use only the signal cable." That Mean using: gnd (nano)- Gnd (Bec of esc ) , D2 ( Nano) - vcc (Bec of esc ) and D3 ( Nano) - Signal ( Signal of esc) IS this right ? Thanks so múchs

fatshark HDO with Rapidfire on the table?

when does it ship?

so getting one!

So it only comes with 3 parts? No Hammer :P

hi guys can this new meter test a tx up to 800mw

Thanks mate been messing around for ages . Watched your video done in seconds 👍

2 years later this vid helped me out awesome 😎👍👍🤙

your video was a big help I appreciate it got a new Quad didn't seem to like the frequency I normally run didn't know about the diff switches on my fatshark just getting in fpv

Nice set up mate. This has same motors as I run by the look of them.

Thanks for video, is there a way to determine best band and channel? I have notice some channels are more clear around my area but there are so many its hard to just try them all. I need some type of scanner to tell me the best band and channel.

Next time record with a proper orientation :-)

I'm having some issues continueing this howto... any idea why the signal is not showing up in betaflight receiver tab? using spracing f3 board with x8r rx on sbus

What is the rx 1 or 0 under my goggles?

Thx heaps for the video mate that was exactly what i wanted to know

Very nice. I found the arduino method very easy and fast to flash my ztw spider premium pro 30a with silab. Thank you.

I was looking for confirmation if the switches on the diagram were the white or black (without trial and error). Logical thinking would indicate, since the switches are white that white represents the switch position but it's the other way around. Thank you :)

Great video! :)

Very helpful! Just got my dominator v3 and that module and couldn't figure out why I had no signal on boscam e when I know thats what my vtx is on, but could get one on boscam a. Seems I was on e after all! Very odd way to show the position of the dip switches. Very counter intuitive. Thanks for clearing that up for me.

Thanks for this video. I am very new to this and is going to give this a try. Just wondering why is the white cable not soldered to the middle pin and the black to the shield?

love vids like these. no bs, straight to the point. thanks

very nice

like a lot of people, i am looking for the easiest way to instal blheli, as a noob, it is perplexing to hear i can have a ztw 18a with blheli but a simonk boatloader which limits my ability to change settings on the esc via passthrough'' all of this info was gleaned from many sources... total pain. after buying the turnigy usb linker i hear that it may or may not have a blheli booloader..... heart sinks.....bear in mind that i have already been stiffed when i bought RWRC 16 blheli esc's which don't work with blheli and now i find i cant change to a blheli bootloader without the usbasp tool and i need an arduino328 to create my own blheli usb linker, on top of the fact when i buy ztw spider 18a from hobbyking... they may or may not have blheli bootloader... seriously?... holy f¿ck i just wanna fly around a little, you couldn't make this any harder if you paid people to make as vague as possible...

thanks mate , this ended a 3 day saga

thanks mate , this ended a 3 day saga

Good info, THANKS !

hello , i have a question plz ,, can we use only afro/Turnigy linker to flash ztw to Blheli ? or we need also Atmel programming tools ?

what bootloader is the best for ztw 18a spider opto esc? blheli or simonk?

What is going on with the options for "MAIN" "MULTI" and "TAIL"... I assume I will use the MULTI for all three for four if I am using a multi-rotor? tri or quad

where can I get the chip programmer.. I have looked all over.. ???

I have some ZTW 20A that were supposed to be blheli but came with simonK firmware. How to check what bootloader they have to know which way to flash? Can I just try the usb linker first or is there an issue if that doesn't work? Sorry man, I goosed up so many esc flashing them I have to be sure.

Hello, I am using ztw spider 40amp esc with Tarot 4114 320kv motors, will theses esc be enough? I have it all hooked up and motors seem to run smooth and esc's stay cool! I haven't flown it yet and have esc's placed so that they get the air from my 15.5 props