Видео

For about 10 bucks you know what to put on those threads 😂 don't be stubborn now son. 🤔we don't want people thinkin ya got a screw loose.

This is either a very lame attempt at satire, or he's an idiot.

You are the reason why all the guns out there people like you. U the wrong screwdrivers and mess the screws up.

You shouldn't even own a firearm you a f****** idiot

Just so you know you a idiot

Been running pioneer main studs /head studs for over twenty years without a problem, I would consult your machinist for your issue.

Maybe it's just trying to get back at you for putting those sights on it!

What a bunch of bologna. You're just looking for something to complain about. That's a good gun.

It's 2024 and the bridge pickup wires are still too short.

Four JM Marlins in my life and never had that problem.

My wife and I were at this show Rockford Illinois What a great show

I would use loctite...or get rid of it if it gives you that much grief.

Name me ONE artist today that can do what 70+ year old Halford can do for this long. They don’t exist Halford was just made different.

Mines the exact opposite. 2001 Cherokee. Switch replaced a year ago and it just happened again. I wiggled around by the blinker switch and it came back on for some days. Back off now. I’m loosing my mind.

Dont want to loctite screws that keep coming loose but yet you rather scratch the gun all to hell lmfao I'll give you 50 Bucks for it since clearly you was born feet first

Hell yeah, good job. Gonna do the same thing to one of mine here in Wisconsin.

The beginning is rear brakes. 14:06 is where I begin the frame repair. 16:45 my most important tidbit to share. 29:25 23 gallon fuel tank swap.

What is the point of this video. You leaked your own address and then like a child you destroy the “tough Chinese crap” that you bought. You don’t just receive fake electronics in the mail.

Loctite is useless on my jm. I shoot with a screw driver in my left hand Seriously.

Bruh, fake AirPods

Does it work?

ahh, the best pros i have aver seen

Those are 200% fakes. Glad you destroyed them, probably 2$ to manufacture the fakes

Expensive?? As a Mexican I thought those are or will be the most common earbuds I even got a pair

bro js leaked his addy😂

Fender sells brass washers specifically for that issue.

😂🤣😆😭😜

Voice coil rub is when the coil rubs against the magnet. A bent gasket impeding the speaker to sit flush is another issue.

Thanks because I was about to use bricks on my challenger replace drive shaft with the same setup.. now I'm getting 2 more ramps so it can't move or I'm thinking jacking each end up and putting the little stand so that the car is jacked and level with tires for extra support if them Jack's fail... what about 4 ramps and jack each tire up then put a ramp under the tire so all 4 on ramps and little stands for support ...thanks for the safety tip

Thanks for your video, maybe try blue loctite to see if it helps 👍

Good looking out

Thank you for this video! I want to make a stronger one, with a single neodymium magnet and bigger copper coil. Can I wind the wire directly on the magnet, with only borders on the side? Or do I need to prevent contact with the magnet with a plastic spool or something?

So, why not loctite?

Not sure what you were going for here. I use a 65 Twin Reverb reissue without modifications and it sounds just right with my 9-string. Don’t need to crank it to the max anyway as I want clean headroom, and then the peals do the job. No Behs tho.

Sold! Wait... did I work on this already?

hi, great VID; can you tell me asap you said r``ad lines snap in`` ; I HAVE A CAR DOWN AND NEED TO PUT THE AZone rad in asap; 'cant affor to break cooling lines:: are they like fuel lines? screwed in? special tool ?? WHAT am I getting into ?

was the grout mixed properly??

OMG, I already noticed a spelling mistake three minutes in... If you're jeep is acting funny or just quits and/or won't start, it's likely these capacitors that have failed. This is the third ECM I have rebuilt. 19:13 is where I show you how to properly use the desoldering wick. The kit was purchased from diy-electronic-store on eBay. You can do this!

WOW!!

Thank you. I will give it a go👍

FERNANDES Sustainers or SUSTAINIAC do not remotely cost 1000 dollars. fun project, but youre needlessly destroying that guitar. Veyz makes a great sustainer custom to your specs for about 150.

Guys on here complaining, and then said don’t tell me a solution… Loctite would fix all your issues and doesn’t have any disadvantages.

Dang! I was thinking about doing something similar but I was really worried about managing the heat, I have a TSL602 and I hear they have a reputation for Seppuku'ing themselves Its been 3 years for you how they been holding up?

Did you buy these off of amazon?

0:55 bhahahaha

You always get the whole car off the ground if you are working under it and never work on an incline on tire ramps! 😵‍💫😵‍💫😵‍💫

I'm about to work on my 300 front left CV axle and now I'm curious if the parking brake will hold the car in place if the rear wheels are on the ground?

So glad you made this video. I have the same issue right now but with the rear shaft disconnected. It's an AWD that the rear shaft came apart on and PARK won't hold it in place. That AWD transfer case must be like an open diff spider gear.

Do you know how many ohms this amp runs at? Wondering if I can use this as a cabinet for my 50W Marshall 1987x

Do you have to get a new distributor or can you just lube it?