Видео

Great video man! Thank you. Just did mine. Took about 3 hours.

Thanks! Do you know why our 2004 Jeep Cherokee Grand UL every time it rains the freaking passenger window,doors back doors & windows ,power mirrors Will Not work.once they dry everything is fine.same with rear lift gate and we needed to change tail light. Its Nuts.we got a New control panel like someone suggested NOPE, went through car wash can't see leaks we are lost.otherwise the vehicle is mint and we bought it for a steal.wish we could figure this out Thanks Again.

Now i want to know another thing. How to LOCK tailgate without key. There is no key thing outside on the tailgate.

What size whench thing did he say?

What kind of tape did you use? Isn't it bad to leave the tape on? It won't cause gap and leak or melt off?

Mi no comprende

Where the video at bto

how long have you been owning a laundromat

Thanks for sharing 🫡

Love how every video skips the axel nut removal 😮‍💨

I lost my key , can i do this without a key?

I’m about to go balls deep into my muranos transmission I’m not excited this cars been a saint

When you did that screwdriver tricked just so you know that's what a u clamp is for. Compress the caliper that will release the tension on the brake pads so you can get them out. If you can press that caliper and it releases your pads then you put pads in then it's not tight. You should stress in the video that's how you can tell if it's your caliper going bad or it's your actual pads. Sometimes it's not the breaks at all its the caliper

This are not tricky. Those basic disk. Not drums.

Exactly what I was looking for. Thank you!

What filter. # did u use ?

Hey body I need your help to put it back my steering wheel. For some reason don’t stay on plase. Help. Please

Orale amigo

Yeah dude thanks for saying to put it in the ON position instead of RUN position and now my damn key came out in the on position and cylinder is now locked in off position unable to remove and unable to start truck to go to work Don't make a video unless you can give proper direction because mine was turning and if you would have stated the RUN position I wouldn't be in this position!

😂❤

Looking very difficult!😮

My wife told me she thinks her brakes are bad because she was hearing a sound when stopping. I checked the left front brakes and they were good so I put that back together and removed the rear and checked that left brake out. It also looked good so I put it back together. When I was tightening up the rear tire I turned the wheel by hand. It turns a few degrees and then when it tightens up it clanks, and when I turn it more it squeals. It doesn't feel very easy to turn either, but I don't know what is normal on that. If I turn the wheel from left to right it takes a few degrees for it to connect with the drive shaft and cause the drive shaft to turn. When it does hook up it makes that clanking sound. Also the squealing or screeching sound is louder if I turn the driver side wheel to the right clockwise. Does anyone have any ideas what this could be? It feels like it could be a wheel bearing or something with the little drive shaft that connects to the rear wheel. Any advice would be very much appreciated. I'm assuming this is something that happens to a lot of these vehicles. It has about 180,000 mi on it. I suspect it's either the wheel bearing or the axle.

Thanks

Good job. Did you change the plug gasket?

I can’t find spring and strut assemblies anyplace for my 05 Maxima. Where did you find them?

@3:27 Thank you so much for showing that technique to apply the deep socket fm the inside and go under the car. I saw several films and people just showed those nuts on connections of the Stabilizer Bar Links, and I had impression that you apply tools on that lower connection fm the outside of the car. I believe someone even did it that way, but it didn't work for me. I tried #18 short sockets, crowfooot with some extensions, applied PB Bluster, nothing. I'll try your method. My car is 2009 Nissan Sentra, exactly same Stabilizer Links.

GOAT

Yeah, don’t do it exactly the way he says there’s more to it, still easy but important things he left out, if you’re going to mislead people don’t make a video dumbass

Thanks bro.

Easy to understand, great idea when he mentioned to take a picture or a video as well as the 15mm socket wrench tightener & loosen. Thank you.

Don’t listen to him

when i push the button my stack dexter will run for 5 mins with doors closed but open it wont seem to go into service mode. just keeps saying .25 when i press the button. any idea what i'm doing wrong?

Lo escuché hablar en español y quisiera preguntarle cómo poder arreglar o si se puede arreglar un crack que tiene donde se le pone el aceite a un Cherokee jeep 2005, sin tener que llevarlo a un mecánico? Mi Jeep está liquiando aceite y notamos que cuando le pusimos aceite, en la parte exterior tenía un crack

That's funny u live in ct so do I and I'm looking for my rears

Take the head rest off for more clearance

door unlock is not releasing the rear glass. All the other doors unlock. Do Jeeps have a separate button for the rear. I don't know why this isn't talked about

Poor instructor

Is it okay if i only swap out the outer tie rod?

Sweet Jesus that tie rod is upside down

I'm watching this as my 2001 wj was making a nasty noise from the rear when unlocking from key fob. Locking it was a normal sound! Now both rear hatch and boot are locked and won't unlock! Anyone know if it's one part that's failed, or two parts failed at the same time? What should I replace?

Dude learn how to fuckin talk and didn't help me at all

Talk to much and no instructions

😂😂😂

Forgot to mention you have to mark and count the turns it takes to remove so u can install it correctly, then its suppose to be on top, and u gotta grease 🔫 them joints for support

You know what? We don't need a picture or a video of this because uh im already watching a video of how it goes on 😅

I like how he's just "winging it" but he's still doing it.

Why 6 quarts? It takes 5

The thing is that if could be shorter

You notice that he didn’t show you how much trouble it was for him to remove or loosen that big nut… this was stupid

Good video. I got it open. Thank you.👍👍👍👍👍