Видео

The set comes with 60 stips i just measured it and it seems there was too much copper 1.5, I just removed the ionizers from the pool for couple of days.

The installation took about an hour as the unit had to be hard wired that was the longest process. I am not sure if you need to make any upgrade to existing setup as long as the BTU is the same. If you upgraded to a higher BTU you might need to increase the incoming pressure with your gas provider and maybe update the meter.

I ran in to a same issue on one of them I had to dig little bit to take out the rock it hit then I filled it back and hammered it down and it went well.

The charger adapter is to power the unit and it also has extra port to power other USB devices but I didn't use the one it came with I just simply used my existing adapter.

I am glad you liked it.

No I don’t have any problem with it works well as it should. It sounds like one of the propeller might not be working or turning slower than the other. Maybe something got stuck you better take a close look at it. If not contact the customer service for warranty claim.

@@ireviewforyou6296 Thank you I will check the propellers again

Hello, please check the description of the video, I have added links to Amazon product pages. Also added the sand link I got for the filter. Before you fill the filter with the sand please make sure of the location of the filter, once you fill it will be nearly impossible to move it without emptying the sand. And I suggest placing a durable piece of wood plank underneath if you are directly going to place it on the ground that is not covered with cement. Once the ground get soaked with water it will start sinking.

To my knowledge only one 49 inch can be used. But you can use 5 of 32” if you buy the 5 monitor mount.

Cmon man its not that bad 😅

There is no option to deactivate the child safety but it is not that challenging to get water from the hot water section even my 3 years old now knows he just need to press the lock button then the one next to it. It is not a concern for me as we never turn on the hot water.

I’m glad it helped you.

Each panel is 38" wide

I really didn’t pay attention to the leveling of the foam but that was a mistake i have some spots little higher than the others it caused little in consistency but i definitely suggest leveling the foam and the bricks on the same level.

@@ireviewforyou6296 thanks I'm really good at leveling I am a bricklayer and I have all the tools to do that I just wanted to make sure before next week what year did I appreciate you getting back with me

The dimensions from side to side is about 17 feet the legs fully extended

@@ireviewforyou6296 awesome thank you!

Currently it is $38.99 and they have 20% coupon.

I never stop my filter so it is up to you but for optimal cleaning I would suggest keeping it on.

The only issue is when i do backwash on the filter and lose some water if only the skimmer intake is active it swallows air because the flow it too much and there is not enough water coming but if i leave the other intake open as well i don’t have any issues it still collecting a lot of debris. If you don’t want to deal with refilling often its better to install right below the seam.

@ireviewforyou6296 I did mine like your and found it's too high;( I don't know what I'm going to do.

@@drdavetexaswhat makes it too high exact,y?

@stevenweede7184 not enough water to run the skimmer through the filter

Sorry for the late response. Each panel 38”wide and 91” height

Initially I didn’t use teflon there was a very small leak then i used teflon very thin layer. I kept one of the other intake but I have a valve on it so I am able to turn it off any time i need better suction from the skimmer. I would keep only the skimmer if the water level is where it supposed to be all the time but after backwash cleaning losing about an inch water causes some air in the pump because the suction is too powerful and it swallows some air with it. So if I keep the other intake open it has even suction and doesn’t cause any air issue. You might have solve that by installing it about an inch below then only skimmer intake would be fine.

The foam is in place it is new and very clean it is hard to see from the angle of the camera. Thank you for your comment.

I’m not sure what size a Stanley one but these are 12.5” there are 2 in the package.

I'm glad you got one and hope you will love it too.