Видео

cisco ASA side, NO-NAT has not been configured, does it not required for IKEV2 policy based VPN?

Thanks for the video, if it wasn't for your video I wouldn't save and restart directly... I updated remotely and everything worked fine. Thanks. (São Paulo - Brazil)

I don't understand the part with management VLAN. You didn't configure routing for it, you didn't configure custom subnet, just make 24 port untagged VLAN10 and connected your PC to it, using ip address of VLAN1 to continue configuring all. Why it all worked if 10.15.10.5 stands to VLAN1, not VLAN10?

A ton better than HP's manual, good work.

The 1960 series has the JL805A intended as an aggregation switch or "collapsed core". A demo config of this routing and securing it down on the switch would be very interesting.

web interface ? No I haven't heard !!!

Thank you so much! It helped me alot. 1. I created the user 2. Created the address and assigned the ssl interface. 3. Created the ssl portal for that specific user and added the source ip. 4. Then ssl settings, added the ip range and added the user. That's it.

Thanks for the guide! I picked up a used FortiSwitch on Facebook for $150 and was struggling to get it working but this helped clear things up

This is one of the best tutorial out there. With the config showing all the time on the screen you can follow along the process. Thanks you for uploading.

Yes, plis how a video on how to backup a configuration from one switch and upload that config into a new switch

Thanks for sharing, well splained congrats!!

Can you show a video on how to backup a configuration from one switch and upload that config into a new switch? I have an Aruba 1930 that I need to replace with a new one.

Hey Mark, Can you show me how to connect a FortiSwitch 424E directly to a Cisco ASR1001, I am having an issue making this work. I can access the ASR thru the fortiswitch and I can also access the fortiswitch, both with IP's on my vlan1, I need to connect to a vlan 4 and a vlan 35 but not working.

Do you have a direct link to download? I recently purchased the 1930 series and am looking to update them.

Best video demoing the setup of these 1930s... No one seems to go near the L3 features in any other video (sort of think they don't know how). I'm trying to get dhcp working through the L3 for various vlan networks on the uplink to a router... Any advice there? :)

Obrigado pelo excelente conteúdo

When I unboxed my Cisco 220 Switch I found I could not connect via the console port. It took me a long time but I figured out that the baud rate was not set to the Cisco default of 9600. Instead the default was 115200. if you cannot connect via the console port try changing the baud rate to 115200.

great explanation!

grate job man, I like it, question: have you test that with cisco or yealink phones ?

thank you verymuch , been searching very long for easier way to inject routing without bgp or import/export map tru vrf definition

'Promo sm'

Is the static route the same as what Cisco call the Default Gateway? I assume FortiSwitch cannot do L3.

Excellent ... well done ... all what you need for Basic-Installation ....

Hello, thanks for this content. I'm trying to connect a phone and then a PC (cascaded manner) in single switchport. is it supported by this switch model ? I don't find a voice vlan command under the switchport config. Thanks in advance!

Thanks so much, good guide. I have the same scenario with the trunk over SFP ports, but I can't make it ping to the gateway, even when the static route has been created. Also, every time I tried to change the "internal" interface native-vlan, to be able to admin the switch later from any port, shows me this error: Native Vlan id cannot be same as system interface vlan. Conflicting SVI: VLAN-709object set operator error, -56 discard the settingCommand fail. Return code -56

Great vid, amazing explanation, would appreciate it if you could show us LACP config, and HA in fortinet switches, not sure if they support stack, vlt/vpc , or just configure a trunk between 2 fortiswitches for HA.

are you able to do it with a tunnel interface instead of a crypto map

very clear and detail explanation, like the side by side comparison between ASA and router.

How can I put an ip to a vlan to manage it either by telnet or web

How to save all this configuration?

👍

Do you use the dashboard or does that require a license?

Great video

Why didn't you allocate static IP for each vlan, and then let's see if ping works from one vlan to another with a trunk on a certain port?

VLAN already running but no internet connection

I can't connect my vlan from fortinet please help

good work dude. ty

I'm feeding two LANs with one 24port 1820 switch at either end. The LANs are via microwave so think of those radio links as physical LANs, or two cables. I need to VLAN two hosts on a 10.10.10.x network to feed one LAN and two to four 192.168.2.x and one 10.2.3.x on the other LAN. I have the manual and your video, but am still confused as to how you assign specific ports to specific VLANs and connect it to the other switch. For example, I created three VLANs and named them. Then assigned ports by "untagged" or "tagged." Using one as an example, I have four untagged ports on VLAN 2 for my utility data traffic. If I have three ports connected to hosts on each end, do I just use the fourth port as my VLAN connection to the other switch?

And what if I have 5000 users .... I will have to create policy object for each one ?

what is the subnetmask of the ip range

I was searching for this since a couple of weeks and stumbled accross this video. Great ! It works ! A few observations : 1. Since the created groups only contains 1 entry, I didn't see the point of creating those. I didn't had to and used users directly. 2. Users (or groups) need to be specified directly in a rule with no other groups. For instance our users are part of a larger group that allows them to connect, and users who needs to have dedicated ips needed to be listed in a separate rule, not with the main group. 3. We uses AD trough LDAP for auth. I was able to add a remote user connected to ldap on the gate for this purpose. 4. I don't believe the change of port is mandatory.

SUPER!!!!!!

Great job! thanks!

good work. Thank you.

wooooohoooooo! thanks - lockdown mode new requirements for Client to Site thanks man!

Nice Job!