- Видео 6
- Просмотров 54 084
MOIRE
Канада
Добавлен 10 май 2013
Videos I wished existed when I was trying to solve a guitar problem.
Turn Your Proco RAT Into a Minimalist Life Pedal
Step by step instructions on how to modify your RAT to add a switchable analog octave before the distortion, and a few other aesthetic mods included as well.
The white RAT used in this video is a special edition released in Japan by Ikebe in Japan.
www.ikebe-gakki.com/c/c-/ef/ef05/ef051076
The OCTAVER mod was purchased from Inverted Cross Audio in Spain
invertedcrossaudio.com/producto/hack-modules/
The black footswitch and DPDT toggle can be found at Love My Switches in Portland, OR
lovemyswitches.com/taiway-3pdt-latched-foot-switch-solder-lugs-black-plated/
lovemyswitches.com/taiway-dpdt-on-on-switch-solder-lug-short-shaft-black-plated/
Special thanks to Modern Technology for letting me use t...
The white RAT used in this video is a special edition released in Japan by Ikebe in Japan.
www.ikebe-gakki.com/c/c-/ef/ef05/ef051076
The OCTAVER mod was purchased from Inverted Cross Audio in Spain
invertedcrossaudio.com/producto/hack-modules/
The black footswitch and DPDT toggle can be found at Love My Switches in Portland, OR
lovemyswitches.com/taiway-3pdt-latched-foot-switch-solder-lugs-black-plated/
lovemyswitches.com/taiway-dpdt-on-on-switch-solder-lug-short-shaft-black-plated/
Special thanks to Modern Technology for letting me use t...
Просмотров: 8 190
Видео
How to wire your HX Stomp for maximum flexibility
Просмотров 32 тыс.2 года назад
Not sure where to put your HX Stomp in your signal chain? Use an insert cable to unlock both effects loops on your Stomp so you can reorder your effects to your heart's delight. Special thanks to @moderntechnologyband their song, Semi-Detached, check out their bandcamp: modern-technology.bandcamp.com Figma Diagram: www.figma.com/community/file/1130956851422011921 EBS Insert Cable: www.sweetwate...
Elephant Graveyard Bass Fuzz
Просмотров 1702 года назад
This is a clone of the Mammoth Fuzz by ZVEX, custom engraved in a rad trapezoid enclosure. For sales on Reverb! reverb.com/ca/item/46242311-moire-mammoth-graveyard-bass-fuzz
How I Fit a Life Pedal in a Fuzz Enclosure
Просмотров 2563 года назад
It was a fair bit of tinkering but I was able to cram 5 knobs, 2 foot switches, and a toggle switch into an enclosure designed for 3 knobs and a single footswitch
Digitech Whammy 5 Encoder Knob Repair
Просмотров 3,4 тыс.3 года назад
I recorded these videos 2 years ago and never got around to posting it. Enjoy!
Life Pedal Clone vs. Original Earthquaker Devices Life Pedal
Просмотров 10 тыс.4 года назад
Want a life pedal without spending ~$700? Build one for much less! Listen to the side by side comparison. Thanks to thehighgain.com for letting me borrow their original Life Pedal. Build Docs www.pedalpcb.com/docs/ParenthesesMini.pdf Buy the PCB at www.pedalpcb.com/product/parentheses-mini/ Buy the enclosure at gorvadesign.com/products/s90 It was somewhat difficult to find an LM308 chip, but I ...
You need to post more vids, these are good! And anyone who says they don’t give a sh*t about “likes” and “subscribes” gets my vote.
21:56 Ha! Your cat is looking for mercy! Lemme out!!!!! I can’t take it!!!!😎
It’s always worth giving encoders and sliders, like those on DJ mixers etc, a good spay with SERVISOL or a similar electrical lubricant spay, as it may just be loose carbon, or bits of…pretty much anything small enough…messing with your contacts. But if that fails then this is the next step!
I loved taking pedals apart, you learnt a lot about what goes into building them, especially older pedals, before surface mount-electronic components took all the fun out of it. You take these Chinese cheapo mini pedals for instance, every one is surface mount. Taking them apart isn’t much fun. Even the EQD LIFE pedal, the v3 (not sure about the previous ones like the one you used) use surface mount technology. I’ll need to check out those earlier LIFE pedals, I think the real early, mega expensive ones, may be hand-wired, old school components, who knows? EQD KNOWS! I’ll have to check out their website . Cool vid.
What on earth is a life pedal?
It's the Sunn O))) (the band, not the amp company) signature pedal. Analogue octave up into a RAT, into a clean boost (and then, preferably, into a Sunn O))) Model T)
I've never seen a white rat. Interesting
If you don't have all those extra peddles but you would like to use your preamp and distortion from your amp + effects from the HX like delay and some of the modulations. But also switch back and forth between a clean amp simulation sound is that possible to do? I'm new with HX and just lost with this thing. Like use the preamp and also bypass it when i want and use a simulation clean tone
Excellent idea! I have a Joyo pxl live pedal switcher. It has 2 loops, you can have 4 pedals in each. 4 pedals to go in front of the amp, and other 4 in the effects loop. I have just adqiired an hx stomp and I want to use its synth effects with my drive pedals, and its modulations, delays and reverbs with my modulation pedals aswell. How should I connect the hx stomp with the joyo pxl live?
This is the best HX Stomp video. But I was wondering… this doesn’t make your delay and reverb go mono?
Does this rat circuit have an onbordr buffer or not?
Tried this but when i go yo FX loop in my HX Stomp is greyed out and cant choose it. What can it be?
Great idea on the boost!
Super helpful. Great graphics. I subbed. Thanks bro!
that POG ❤
can you send a link, to buy the part? thank you so much
You’ll need to call full compass 800-356-5844 and ask for a rotary encoder part #44-0114
Looks like you can actually grab these off Ali Express, 20mm and it’ll work www.aliexpress.us/item/3256803820819323.html
Awesome, will try this asap!
I clicked on the thumbnail because it was well designed. Seeing that it's you, everything makes sense. Awesome channel Sir!
what size is the alan key your usoing?
Cat: "oh for god's sake, again with the noise" lol
Do you have a diagram that shows how to run physical dirt pedals in front of the amp with the 4 cable method and have physical modulation pedals in the amps effects loop? I don’t have this splitter cable yet so I’m curious how i get that to work for now but I’m confusing myself where in the physical instrument cable chain to do this. Mostly with regards to my modulation pedals and finally my looper pedal.
Is something missing from this? www.figma.com/community/file/1130956851422011921/HX-Stomp-Effects-Loops the little lines here are meant to represent your cables
@@moire.visionyea this makes sense now. The only other thing I’m trying to figure out is with this setup can you introduce an emulated booster pedal after your physical dirt pedals but right before the preamp? Similarly any emulated pedal right before preamp but after the dirt pedals? I think anything after any of the send or return loops would go in the effects loop and be after the preamp unless you put it before and then it’s going to go in front of the physical dirt pedals, I think?
@@silvel2edge yeah I could do that with my new setup with the Morningstar ML10X, but you’d need a third effects loop on the stomp to make something like that work.
Thank you for your help would amp pedals like iriduim or tonex go in the drive route
Or just add an EQD Accapulco Gold to a reg. Ol Rat. YW.
The octave isn’t talked about much (or at all, really) but is pretty integral to the Sunn sound, if that’s what you’re going for. I’m not even sure the fuzz pedal you use is particularly important; I put an analogue octaver before a Muff recently and bam, instant Sunn. It’s more subtle than the sort of clanging chainsaw octave you get with a Super Fuzz/FZ-2-type circuit, but it’s there.
impressive,..thank you so much for sharing this idea of writing up drives and modulations section s in separate loops. One question though,..I have 3 amps and wanna set it up in a wet/dry/wet scenario,..could you do a separate video on this please?
Working on a stereo version of this with the stomp + Morningstar ML10X right now
Can’t wait for this, I’ve been racking my brain how for months.
@@Forkandles88 got the setup sorted out. Just need to find time to make a video.
Awesome dude, I’ll be watching. 🙌🏻
Octaver mods from inverted cross are back in stock today! invertedcrossaudio.com/producto/hack-modules/ If you want a mod done for you, the zero fret is about to do a more in depth mod run soon thezerofret.bigcartel.com/product/god-mode-rat-tzf-modded-proco-rat
Could you use a pot instead of a switch as a blend?
Yeah it’s totally possible. The zero fret is doing this on their upcoming run of rat mods instagram.com/reel/CqTpVJ-IzHA/ I think it might take a dual gang potentiometer www.stewmac.com/video-and-ideas/online-resources/learn-about-guitar-pickups-and-electronics-and-wiring/blend-pot-wiring/
The guitar in the picture is actually plugged into the footswitch input. Left input would be one to the left. But I hope people get that
lol, you’re right. Whoops!
Thank you! I just resolved my rotary encoder knob issues on my Whammy 5 and your video really helped. You’re awesome! 😊
Thank you! I was banging my head against the wall trying to figure out how to open this thing and never had success. Will try this soon. My bypass LED died within a few weeks of buying one new. Have lived with it for years but hopefully not much longer.
hello, I hope you are doing well. I am setting up my rig today from your video. Thank for doing this! Good job! Where would you put your tuner ? In front of everything? Guitar-Cable-Tuner-HX Stomp?
You can use the HX Stomp tuner. I use a rack tuner and split my signal first thing in the chain and run a dedicated cable to that. If you have old school fuzz pedals that don’t like buffers, put your tuner in line after those. If not, just put it first.
Dude you are a lifesaver. Thanks for putting this together. Most appreciated.
the poor cat lol looking for an escape route
Wow. That mod makes the rat sound WAY better. Honestly it balances the frequencies out. Impressive. Oh and I respect how candid you are about not caring if we like/subscribe. Too many people beg now a days. It's sad.
That tone was violence! 😮
great mod? BUT- the <octaver> module from invertedcrossaudio is sold out. Any idea if there's a similar solution? Will be shipping to the US.
I haven't seen anything as easy as that, but it's certainly possible with any green ringer pcb like this: buildyourownclone.com/products/octave-up-module
i bet your cat loved it
love it!! it sounds huge, what amp are you using? also, what's the song from the start? also also, do you have some original music that i can listen to? love the tones you got there
Song is by modern technology linktr.ee/moderntechnology I need to post some tunes soon!
Also the amp is a Science Mother
What’s that expression pedal, thanks!
@lehleswitcher dual expression
what was that battery compartment cover?
Temple audio mounting plate www.templeaudio.com/pedal-plates
@@moire.vision thanks homie! the more i read about the templeboards, the more tempting they become.
@@C0nnie I’ve loved mine for years, no regrets!
Homework time! But I think I got it. Great video too, thanks for sharing 🤘
Hi, thanks for video! How do you set up d.a. midi baby 3 with hx stomp?
Here’s a good resource www.thegearconfessions.com/post/midibaby
Great and very creative idea and performance of maximizing the most of it !!! well done !!! I'm curious as to how would you go a bout in regards to a dual amp + hx stomp only (!!) meaning no external pedals ? Lidor
Listed this for sale reverb.com/item/63970962-proco-ikebe-limited-edition-rat-2-octave-black-footswitch-mod
Sold!
Great video bro. Do you also know how to connect hx stomp direct to the PA system in stereo?
If the PA you’re using has no instrument preamp (assuming it does) I’d recommend a stereo DI box
Love this 👍 like the honesty at the end 🤣 definitely getting the mod from inverted 👍
this is much better than paying $300 and receiving a broken piece of shit.
Still always a danger of breaking it yourself though :) I was a bit worried about that on this one but it worked out.
Thanks Jesse, great video. I guess you could change the on-on switch for a DPDT footswitch? ("Don't give a f*** if you Like it Subscribe" - love it...)
You could definitely use a DPDT footswitch or even a 3PDT if that’s all you have handy. Might be a bit awkward to find a good place for it though.
thank you very much - totally solved my pedalboard setup and my confusion about adding a hx stomp to it.
You could clean, instead of buying a new one. It works. I saw a guy doing it. Clean with electrical lubricant the old rotary switch
Good information thanks. What happened to the screen on your HX system?
What do you mean?
@@moire.vision it looks like you took some sandpaper to the screen did you not watch the video.
this really open my eyes ive been wondering how this is being done thank you for this video