Видео

They are aren't they. I took it for test, laughed my head off. Nippy little thing lol. I enjoyed driving it. Different to my transit haha.

Thanks mate 👍

No it's not. Terrible paint job. I will upload a video for you to see 👍

Thank you. I'm in the UK. North Yorkshire. 👍

Thank you 👍

Hi, i can be contacted via my Instagram Supercarlsunday or ticktock if you would like to discuss further. Thank you 👍

I never have any issues because I have been doing it for years. If the gap is tight. Knock it down with a piece of wood. Put a piece of wood on it and tap it down with a hammer. What screws do you mean underneath? Are they the temporary ones i have put in to hold the panel maybe? If so, they are removed once the panel is tacked in place and the holes welded up

@Supercarlsunday thanks. Yes I meant the screws underneath. I was thinking more about the video and wondered if I was being stupid - when you cut through the new and old sill at the same time, are you then removing the old part from underneath? Is this to make the top of old sill and beginning of new one meet up perfectly? I ask because I can't see any transition where you would have had to use filler to mask the 1mm higher new panel blending into the old if they remained overlapped .. Thanks again

@03056932 you remove the old panel underneath and butt weld the new panel where you have removed the old one. You can also put a piece behind the join to weld to. Some people do this and some people don't. It's good to do if your not a great welder. The screws underneath are temporary to hold panel in place.

@@Supercarlsunday this is really helpful for me. To get clarity. Thankyou so much for replying!

@03056932 No problem, glad to help. Best of luck with it 👍

I did sand down the old paint. Both wheels were prepped up and primed. Did you not watch the whole video?

Thank you. I appreciate your kind comments. I do have quite a few customers. Where abouts in Brisbane are you? I visited last in 2019.

I use it daily, and I'm still using it now. It's as it was when I bought it. The only thing is, it does need a couple water traps and draining daily! It gets a bit of water in it. It could be due to the small tank..

@Supercarlsunday i will buy bigger one 200L 6kw , enough good for sure.

@brosagt3822 definitely

I've got the 50L unit as in this video. Very good bit of kit compared to the piston type compressor it replaced and the air output is very close to quoted numbers with significantly less noise. I run it with a DropOut autodrain water separator on the outlet side and that takes care of any condensate. The 200L unit will move a LOT of air 😊

Thank you, I appreciate your kind words. I hope you subscribe. I have some good projects coming up.

Ha ha ha ha, it was early days with the channel! Still a fantastic tune! Obviously not your thing lol! Each to there own hey 😀

@Supercarlsunday It's a good tune, just doesn't work on the video 😂

Lol, at the time I put this video together, I didn't have a clue what I was doing. I definitely know what you mean lol. A video like that now I'd just speak and explain what to do. I wouldn't speak on camera before 😂..

@Supercarlsunday Fair enough, everyone's gotta start somewhere. At least you're doing it 👍🏼

@outshine5411 That's it. It is time-consuming. Thank you 👍

It didn't last long here. It went the same day.

Richmond North Yorkshire.

No problem Julian. The next update won't be to long. I have footage of building the engine and possibly when we put it in.

Thank you 👍

Hahaha. It's not a nice job 👍

I can't remember off hand. There is lots of videos on the build, there should be one that Includes the exhaust brand.

Thanks i found It

@martinbruonc2955 That's great. What was it on that one?

Fresco big one

@martinbruonc2955 Yes, that was it. It was alright. Had a dep on another one.

Delkavic 👍

Thank you. I'm. Glad you enjoy it. Please keep following for my Christmas give away.

It was cleaned up! I always clean up the area before applying filler! There was no burnt residue mixed in with the filler at all! Watch with your phone and zoom in! Your mistaken!

Thank you.

Hi, the same as your power commander on your fuel injected model 😉. I have quite a few videos on my channel of this bike. 👍

Why do you hope it's a none x/o ring chain?

You're only stretching if you're over pulling. The panel is already stretched in the crease. You do what works to get as much damage out and use minimal filler. Thanks for your input on the video.

Thank you 👍

Thank you 👍

This one is a Vauxhall. But yes ford's are not great. I need to underseal my transit ready for winter.

That's cool, thanks 👍

It should be

I don't think that one is done yet.

Thank you, lots more to come 👍

I drill them, wax oil and then rubber grommet the hole 👍

I don't understand, sorry.

Thank you mate. I will put a better video on soon 👍

@Supercarlsunday will look forward to it 👍

Cool 👍​@@paulfeatherstone7095

That's not a hair dryer I'm using it's a heat gun and I'm heating the bent parts up, pushing them in to place then cooling them so they stay there. This is the proper way to do this. I have been doing this for years. As you can see, it's done the job. 👍

Because it needed fixing lol

Hi, why are you taking the right crank case off?

Thank you. Maybe you could teach me maaaan m! Yeeee haaaa 🤠

Contact JL in cheque Republic they should be able to ship you one out.