![Alarm Assist](/img/default-banner.jpg)
- Видео 67
- Просмотров 476 705
Alarm Assist
Великобритания
Добавлен 30 апр 2019
Fire and Security System Tips, Tricks and Help. Here you can find help for programming and installing security systems in your home.
We do not favour any system make were just here to show you how to program, install and fix them!
We do not favour any system make were just here to show you how to program, install and fix them!
Loops Stopping/Initialising of the Fike Duonet. If you removed a device and now get a fault use this
How to stop and start the loop on a Fike Duonet.
Note this must be done prior to removing any heads or devices.
If you have removed a head etc and are now getting a fault follow this procedure to reset the system and get the loop working again.
If on initialisation the device numbers don’t match to the ones originally shown a device somewhere along the line hasn’t initialised or is missing. This will cause all devices to be out of place. To find this device carry out a walk test until one doesn’t test correctly or you start noticing devices out of sync, replace device and follow this procedure again.
Note this must be done prior to removing any heads or devices.
If you have removed a head etc and are now getting a fault follow this procedure to reset the system and get the loop working again.
If on initialisation the device numbers don’t match to the ones originally shown a device somewhere along the line hasn’t initialised or is missing. This will cause all devices to be out of place. To find this device carry out a walk test until one doesn’t test correctly or you start noticing devices out of sync, replace device and follow this procedure again.
Просмотров: 84
Видео
How to change the code on a Videx Door entry system.
Просмотров 2 тыс.5 месяцев назад
How to change the user codes on a Videx access control system. Default Eng code is 111111 To default engineer code remove all power and hold enter button on power up. Carried out as followed: -engineer code”Enter” red light shows -enter existing or a new engineer code “enter” beeps -Enter new user code “enter” -enter exit delay in seconds 10-99 “enter” Hit enter twice at this point to exit menu...
How to put the older Concept Firesence into Test.
Просмотров 4517 месяцев назад
How to put the older Concept Firesence Fire Alarm Panel Into walk test mode.
What to do if a Menvier 8 Zone has a system fault that won't clear.
Просмотров 4019 месяцев назад
What to do if a Menvier 8 Zone has a system fault that won't clear.
How to put the Menvier 8 Zone Fire Alarm Panel into test.
Просмотров 35710 месяцев назад
how to isolate sounders to allow testing of the Menvier 8 Zone Fire Alarm Panel.
How to put Eaton biwire flexi fire panel into test.
Просмотров 62210 месяцев назад
How to put an eaton biwire flexi fire panel into test.
How to put the Ampac Loop Sence Fire Alarm into test.
Просмотров 53610 месяцев назад
to to put and remote the Ampac Loop sence fire alarm panel from test mode.
How to change the Date and Time on a Scantronic Alarm system
Просмотров 665Год назад
To to change the date and time on an older Scantronic Alarm system
how to change the dialed number on a Guardtec dialer.
Просмотров 144Год назад
how to change the dialed number on a Guardtec dialer.
How to change the number on a Texecom dialer
Просмотров 1,4 тыс.Год назад
How to change the number on a Texecom dialer
How to put a Gent Vigilon into test.
Просмотров 1,2 тыс.Год назад
How to disable sounders and output on a Gent system to enable you to carry out testing.
How to walk Test a CTec XFP
Просмотров 2,9 тыс.Год назад
How to Test a CTec XFP addressible fire panel.
How to change the clock on a Texecom Premier Elite
Просмотров 2,6 тыс.Год назад
How to change the time on a Texecom premier elite. Note with smartcom this should change automatically.
How to change the time on an Orisec Alarm system.
Просмотров 164Год назад
How to change the time on an Orisec alarm. This is shown on the virtual keypad but the physical keypad is exactly the same.
Texecom Veritas Beeping and not setting.
Просмотров 8 тыс.Год назад
What do the beeps on a Texecom Veritas mean?
How to wire Normally Closed into a Texecom premier elite expander.
Просмотров 828Год назад
How to wire Normally Closed into a Texecom premier elite expander.
How to program a Texecom Veritas Excel
Просмотров 8 тыс.Год назад
How to program a Texecom Veritas Excel
Full programming for a Texecom Premier Elite.
Просмотров 25 тыс.Год назад
Full programming for a Texecom Premier Elite.
Texecom Connect Failed Cloud Update (Two LEDs flashing on smartcom).
Просмотров 1,1 тыс.Год назад
Texecom Connect Failed Cloud Update (Two LEDs flashing on smartcom).
How to put the HAES Alarmsence plus / advanced Quickzone into test or disable zones.
Просмотров 1,5 тыс.Год назад
How to put the HAES Alarmsence plus / advanced Quickzone into test or disable zones.
How to Test a CTEC CFP Series Conveniental Fire Alarm Panel
Просмотров 15 тыс.Год назад
How to Test a CTEC CFP Series Conveniental Fire Alarm Panel
When to use SAB or SCB on an alarm sounder? SAB & SCB Explained! Lesson 1
Просмотров 2 тыс.Год назад
When to use SAB or SCB on an alarm sounder? SAB & SCB Explained! Lesson 1
How to test the Honeywell Notifier Pearl Fire Alarm
Просмотров 1,8 тыс.Год назад
How to test the Honeywell Notifier Pearl Fire Alarm
How to Test an older model Kentec Series 6000 Fire Alarm Panel
Просмотров 512Год назад
How to Test an older model Kentec Series 6000 Fire Alarm Panel
How to put the Fike Twinflex Pro 2 Fire Alarm into test.
Просмотров 3,5 тыс.Год назад
How to put the Fike Twinflex Pro 2 Fire Alarm into test.
Ethernet ports not working in new build?
Просмотров 4 тыс.Год назад
Ethernet ports not working in new build?
How to add Proxy Tags to a Texecom Premier Elite
Просмотров 1,7 тыс.Год назад
How to add Proxy Tags to a Texecom Premier Elite
How to change WiFi providers on an Orisec Intruder Alarm Panel
Просмотров 1 тыс.Год назад
How to change WiFi providers on an Orisec Intruder Alarm Panel
How to connect an orisec alarm system to the app.
Просмотров 1,1 тыс.Год назад
How to connect an orisec alarm system to the app.
How to Connect a WiFi Module to an Orisec panel and connect it to the WIFi
Просмотров 1 тыс.Год назад
How to Connect a WiFi Module to an Orisec panel and connect it to the WIFi
Gonzalez Frank Harris Angela Hall Amy
Whats engineers code so I can change my own please
Thank you
Well explained 👏 😊
Thank you for this video mate ! Followed step by step and worked perfectly 👍🏻👍🏻
Hi, is there any way to silence a fault after cutting a wire to an alarmed area that I am not using anymore?
Is there an easy to do setting on the control panel so that 2 sensors need to be activated before the alarm triggers?
Some of my motion detectors won’t set the alarm off when I walk past them? I’ve learnt them and added code 06 for intruder but nothing happens ? Can you help out ?
Hello, Can You Show A Video Of How The Chime Sounds Like On Veritas Excel Or Premier Elite?
I have access go panel denied, anyone got any ideas?
Can I trigger the alarm via an API does it support PoE?
So it connected without the aerial?
Thank you
I have "access to panel denied" any ideas?
Me too, did you get to the bottom of it?
@@derekrodden551 Yes if you search "DIYNot - Texecom alarm connect app issues" you will find a forum I can't link.
Is it possible to do a quick test the of the sounders without a panel key?
After being on hold for 5 minutes with Texecom support, I was offered a call back. Turns out call back was not available so they cut me off. Your video sorted me out. Thank you.
You shouldn’t be doing videos if you yourself don’t know how to use this system
Hi Mate. Not sure if you are still on here. I have an old Gardtec alarm. Was fitted when we bought the place. It's been pretty solid but for 14 or so years since we have lived here. Replaced the panel batteries a couple of times but apart from that no issues. However, in the last month or so I keep getting a Bell Box Tamper alert. Alarm just randomly switches on even when it's been disarmed and we are home. Goes off at all hours. Really annoying. Does that mean the bell box needs replacing? Its fairly old. Could it be the battery in the bell box? I haven't got a clue when it comes to alarms. Not great with ladders either but will climb up if I need to. If it was the battery I would have thought it would state a battery error. Anyways. Not sure if you are still here but any help would be great. Cheers.
Did you find the fault by any chance?
@@stephenblack9843 I replaced the bell box battery. Thought it fixed it but then 2 days latter started triggering again. Ended up finding someone who removed and refitted a new box for me. Ever since (touch wood) it hasn't gone off randomly and has been. Fine. If that didn't fix it I would have replaced the whole thing as it's pretty old now.
Thank you
Would it be the same for a texecom Veritas R8 system?
What do loop integrity fault mean
Great video, very handy 😎
Hey - I've just changed ISP and managed to get online. However, after about a week, the app has stopped working. Is this to do with IP setting on control panel? When I "view module status", signal shows as 100% but status "Not Fitted" - any ideas please? 🙏🙏🙏 Thanks in advance 🌹
Hi, great video Some questions: Do the resistors normally come with the panel? Do you think it is ok to carry 3 zones through one cable on an 8 core? E.g Parallel wire the 12v power and use other 3 pairs for FSL zones?
Great video, thanks!
Learnt quite alot in this video. I've installed a Texecom alarm at a customers house but have no idea where to begin in setting it up. If I can't do it after watching this video then I'll have no choice but to call a professional person out lol
Love your video. I've followed your instructions, I arm it but when I open the door or walk into a room, the alarm doesn't go off on the sounders 😢
Good instruction video, I know you said double knock don't worry about. But think its very useful I for delaying the pet false alarms in my family room / kitchen area. Also use that in my office upstairs so once part set is done before bed I can put my macbook etc in my office with the 10 second motion delay feature which works out great. Incidentally to go back during TEXT use the CHIME button. Thank you👍.
Excellent tutorial that covers a gap in the Manual. Changing a router should be an easy experience as it is quite a common thing to do, yet the user manual does not cover the fact that the password is in a different section from the Wi-Fi, so even if you change the router in the wi-fi section, it retains the old password in the Coms module. This is not covered in the manual, my alarm provider seemed unaware and wanted me to pay for a visit (£50?) for something a user can do, makes you wonder... Please retain this Utube video for all the other confused users of this alarm, and Thank You very much.
How do you change the main welcome text “Dartline Alarms” it’s set on this one. I have been scratching my head for months with that. Can’t find any option i can edit it
Good work keep it up
So.. I need 4 ethernet cables to go from hub to them ports next to box.. then all other ports around the house will work? That's alot of ethernet cables haha
Just tried this all went ok until the keypad set up then it froze saying connected had to reset alarm now I have keypad listed in zones 1 to 8 with tamper and I can’t do anything else I delete the zones but they keep coming back and it’s says richocet not available, keep resetting panel but just keeps doing same and won’t search for wireless sensors can you help!
I use this video once a month. always forget how to do it. Such a life saver thanks
Thanks for your video, how to set silence Arm ?
Very very helpful thanks
Hi, i have a smartcom that will not connect via wifi but will with ethernet. Any thoughts. Smartcom v4 and premier elite 48 v6
need to update smart con
Hi there - I tried this but when I scanned for our new wifi router it is just stuck on ‘Scanning for Networks’. I can’t get it to stop. Do you know what I can do to stop the scan and retry?
Did you ever get a fix for this? I've got the same problem!
Thanks this worked for me
Brilliant info. Thanks 🙏
Managed to get buttons 1-3 to work on both my keypads but can't get the app to work. Used keypad 3 and followed steps but doesn't give me option in app
Mine doesn't have this option . Must be an older version
I’ve done all this but still not receiving and internet from the port
Check if there's cables behind the ethernet plates
Your RUclips channel logo is marked with a texecom odyssey 5e bellbox
Mario and james have got this pannal
Great video. After how many years would the siren's battery need replacing if ran in SCB mode? Cheers
Can you buy this and install DIY yourself is it easy enough? Also will it let me use the App to control?
I now need a video of how to undo it 😢
Is there a way to wire 2 SABs/External Sirens to a Premier Elite, both at full output power?
Hi, I have fitted the petwise PIR’s. Hardwired in. I have them in my hallways, one facing the front door. But it does not seem to detect anything when doing the walk test.