Видео

you can use cpu 1214

Hello, if PING works towards the PLC, type in the command prompt PING IP address from the PLC and see if the ping goes through. It is for you to see if there is communication with the PLC. And you don't need a switch

@@muhamedpasic83 Plc stops recording when it is turned off and on again. It stops when there is a power outage and does not work again. How can I run this automatically? What should I do for this? How can I make adjustments in the Db section?

For example, if you have a gear on the encoder, you calculate the circumference of that gear. Because what is the circumference of that gear, the encoder turns for one revolution

In the first part of the video block_1 is programmed and it is the name of the function (FC). An encoder is programmed in this function called "block_1". And then block_1 was just dragged into the "Main" block for simulation. So block_1 is the main one and the read value of the encoder is programmed there

Which version of the TIA Portal are you using, you should have a techonology in which CTR_HSC is located, if that's what you meant

I took a specific example here. A gear is monitored on the encoder shaft, so when the encoder makes one revolution and the gear makes one revolution, that is a path of 141mm. The circumference of the gear is 3.14*R, the R-diameter of the gear, so the larger the R, the larger the circumference of the gear. In my example, the diameter was such that when the circumference is calculated, I get 141mm. There will be a different scope for some other gear

yes, you can use REAL

Hi. Can you make video like this with Delta through the DOPsoft? Thanks

Watch the video from 0:58 to 1:28 minutes

The value obtained from the TC module to which the thermocouple probe is connected for temperature measurement is multiplied by 10. So, if the actual temperature is 25 degrees Celsius, you will see 250 degrees Celsius in the PLC program. Therefore, this value is divided by 10 to get the actual temperature value. Because in the TC module, automatic scaling of the temperature value is performed, but only increased 10 times, and therefore it must be divided by 10

same procedure

Create a new project, do not add or create anything in it, and click "accessible devices" and see if you can connect to that CPU

Ethernet And the type of plc is Siemens s71200

Can I have your email ? Please

@@loicnzundja656 The IP address on the PLC and the ethernet cable should be in the same subnet, eg 192.168.0.x. x can be for PLC 1 and for ethernet cable 10. TIA Portal should automatically assign the appropriate IP address for ethernet, but if you have a problem, add it manually. Manually assign an IP address to the network adapter

software units is used when two or more programmers are programming the same PLC at the same time. Everyone programs their part independently of the other

Check if the HMI and computer have the same subnet, for example 192.168.0.x, then check if the same HMI as the actual HMI is selected in the program (TIA Portal). The signs must be the same as these Siemens markings, for example 6AV6 647-0AK11... Check the ethernet cable

ruclips.net/video/Mo8Y2F2Omuc/видео.htmlsi=WfTiQzKWdFBySlLz

ruclips.net/video/j45VO5BIahQ/видео.htmlsi=uNl5AhY5uqQ3WszI

ruclips.net/video/WKUFK__gDb0/видео.htmlsi=wfYVkDvCg4QYPmET

ruclips.net/video/_1C9sK0m4TM/видео.htmlsi=6FQIdYHEDA5r3sHY

ruclips.net/video/JjmzX5y_-Bs/видео.htmlsi=g2jskyHftrUJKQev

For consultation please

ruclips.net/video/Mo8Y2F2Omuc/видео.html

Dobar dan, trenutno ne, zbog obaveza

It's 3:41 minutes into the video. LADDER=256, it is the starting address of the telegram used by this encoder. This telegram uses 4 bytes, which means that the position of the encoder will be recorded at the address from 256 to 259

Set the type of counting to "frequency", watch the video again from 1:15

@@muhamedpasic83 When I use Frequenzy, my ID1000 is not updating at all. Thank you for any input or help, I have tried for days without any correct output.

I am proud to be Bosnian, I wrote Croatian-Bosnian because there is no Bosnian language in TIA Portal, but there is Croatian language. And the Croatian and Bosnian languages ​​are very similar. Proud Bosnian...

@@muhamedpasic83 that's it glad to see your tutorials anyway

this video was recorded with V15.1