Видео

I'm guessing nobody had a key to the backhoe.

Can you please tell me what kind of truck this is ?

The two idiots trying to push the front of the truck sideways, should never be left alone.

Gotta ask: how many pedos can fit through the machine on the back?

Better shocks and mounting the clasp higher would be a big help. Also, a little more weight on the nose to get that ass up would help too. If it's an automatic transmission, it's not gonna like that line of work, but with a manual transmission, it's just fine.

🙄

That's what I'm talking about!!

MT & 40 badically same tractor aren't they?

This series was very helpful to see what's involved in doing steering clutch/final drive work on a 450. I have two 450C track loaders that I'm trying to decide what to do with. One with stuck engine. If I part them out, are parts worth much? Have one good undercarriage, and a cable winch with logging arch. If I spent some time I might be able to make one running tractor out of two, but I'm not sure it would be worth the time. I could do the work myself if I decide to repair one machine....don't think It wouldn't be cost effective to hire repairs done.

We always had problems with blowing head gaskets on the 16s.

Are they wet or dry clutch in the 450BC

I have an old Yanmar ym2000 that needs work, could t get in touch with tractor town. Replaced battery a few weeks back, put everything back in place started up & ran but the alternator started smoking, took off the positive cable the smoking stopped. Anyway possible for me to get in contact with you?

Where did you find the common rail pressure sensor WITHOUT going throw kubota an having to get the common rail plus senor together

Do you know how much horsepower this Tractor has ?

Thats a good running tractor

Otis, did you see my second question: Can I access the 7/16 bolt going into the spline (access through the peep hole) by removing the main plate under the battery compartment? That 7/16 bolt is broken off and is allowing movement on the shaft. Some way I need to get it out so it can be properly installed with a new bolt. Is accessibllity possible once that large cover is removed if not open to suggestions.

Otis, now that the final drive is removed send me a picture where that 7/16 bolt is located ….from the back side of the final drive. Thank you for the video, very helpful!

Question: the bolt that you used a 7/16 wrench on through the “peep hole” that you in UNtightened that tightens into the grove that hold the

good lord that looked bad lol but in NC its been up to the low 100's with all the humidity

good lord that looked bad lol but in NC its been up to the low 100's with all the humidity

How much does it cost to change the ClutchJohn Deere 450 track loader including part in labor thany you

I'd love to own one with a winch, and blade. an ol MC or 40 model was the first dozer I ever ran and would love to have one to add to my ol equipment roster, I own a ol allis hd5b but she's been heavily modified I use for my business and could use something a little smaller and one a little bigger funny enough

You wouldn't happen to know anything about a 269 new Holland square bailer would you?

i aint ever heard of no 2240 but good to know that the bolts like to back out if i get one

So true

Favors a 1010

Clean and good rubber

Dang right I like tractors

That's begging for a cab and skid pan for the woods bush hogging

I have a 1949 9N, still love it. Do you have s brush hog with it?

Are you confused with a licensing agreement between IH and Mahindra to build the tractor for the India market in India (Similar to Massey Ferguson & Tafe)? Some internet history shows parts from England shipped to Louisville KY for tractor assembly. Any IH workers out there from the Louisville plant?

Tractor fail or lug nut fail? Shabaura tractors were the best coming out of Japan in the 70-80’s time frame. Ford /New Holland should never have severed the relationship with them.

I love my old ford 971

Just had Diesel on my L3901 tonight. That is NOT where the connector is. The connector is the BLACK 4 pin connector to the left of those two. It matches diesel connector 3151/T55. Oddly enough the tractor I am working on is also having injector issues. I was able to do injector kills, read the coding on the injectors and verify the high pressure pump was working fine.

That is one beautiful tractor

These were the best of the 7xxx series. 268 vs 256 engine, better hydraulics and no Load Monitor sensing. Load Monitor needed better flow to be a great feature which ironically the later 10 Series II had. Got rid of the springy balls on the ramp actuator in the drive line for Load Monitor as well.

didn't know they made a high crop 4020 neat

Never run one but those fords 7610's seem to run forever and are very simple

Fix it it's a beast

Looks like it's in need of a new set of rings and a head job!

Beautiful Deere love the sound of those popping Johnnys

Nice units. Any of them for sale?

I had a br all it did was cut fire wood. Had a buzz saw mounted on the front. Bought it for 75$... Sold it for 5000$. Should of never sold it😢

nice runnin deere

Tylen love 💘 ❤ 0:14 ❤

Sell it yet?

For sale?

Do I like old tractors? Nahhh 😂

So you think making a RUclips video just means putting a camera on a stand and let it film you working.? Ok may suit some not me, I like to be included and spoken to, or at least a running commentary on what you are doing. I'm gone.

Is there suppose to be hydraulic oil in the steering clutch compartments? Mine is full to the top on both sides and leaking out the top. The last entry in the mech logs before i got it at auction is" hyd oil leaking into clutch. I assumed they meant the main clutch. I did see an early service bulletin On the 80's 450c something about making the clutches a common sump because of a hose that leaks? I have been looking for an oldtimer mech that knows the 80's 450c inside and out. So i could pick his brain. They are all retired :(