Видео

@@angelrondon2631 2010 Mazda 3 with a 2.5L engine: OEM Belt: L3K9-15-909-9U (Mazda Original) Gates Micro-V: Part #K060900 Duralast: Part #900K6 Continental Elite: Part #4060900 Bando: Fits 2010-2013 Mazda 3 2.5L L4

The air fryer is a Ninja brand

@Ifyouthinkyoucanillshowyouhow is the air fryer massive?

@@avenhall881 14.9"D x 14.9"W x 11.02"H

@@Ifyouthinkyoucanillshowyouhow is it massive

Thank you, burning the candles at both ends!!!

Was it draining your battery over time as well? Mine just started doing this as well

Freshly ground cinnamon does make a big difference-it’s more aromatic and flavorful than pre-ground. The smell is incredible while grinding, and it adds an extra depth to the dish!

@Ifyouthinkyoucanillshowyouhow then I guess I'm going to have to try! 😁

I’m sorry I don’t understand the question, This regulator had snapped, I raised the window up using my finger and then a screwdriver to hold it in place to unscrew the Phillips screw holding the window in place. It was hard to unscrew.

@@micheletjuniorfleury9654 if I remember correctly I left it in place to the side, you can get the alternator out the front, if I remember correctly you may need to move the secondary air injection valve.

@@ataiman5897 call the dealership with your VIN to see if it even has a serviceable fuel filter, most new car just have the one at the fuel pump.

No need to drain the oil, the engine should be off so no pressure, engine should be cool if possible.

@@Ifyouthinkyoucanillshowyouhow sweet, thank you!

Thanks ​@@Ifyouthinkyoucanillshowyouhow

You’re welcome

10 MM with extensions and swivels. PB blaster to get it loose, flash lights, padding for your knees because your gonna be on top of the engine. And about 3-5 hours worth of cussing 😂. That's what it took me yesterday and this morning. Don't drop the bolt if you do it's a m6 inch long bolt at the hardware store.

​@@francisgarthow1459 this is funny! I did the front one just now and the two camshaft position actuators. I have the part for the back one like this video but I said nope! My code was p0013. So I just wanted to do all parts in that area. Why not. But this one... I think I will wait for my day off. Oh and I am in AZ. So doing this at 113 degrees today. Its going to really multiple the bad words.

If my memory serves me correctly it was making noise. The loud hissing sound sucking in air.

The vacuum line was broken. It was visible. There was a vacuum leak code, unfortunately I don’t remember it.

Thank you for the reply! I have a very rough idle problem in a similar car that acts like a vacuum leak, but doesn't throw any codes; did the throttle cleaner spray method but couldn't find any vacuum issues. Next suspect is the engine and trans mounts. I was hoping it wouldn't come to that lol

​@@quiencreesguey p2279

I’m getting to replace mine soon (part is in transit). I had a hissing noise (break in the line) on the right side of the intake manifold (part of the line was exposed on the right side of the IM). I discovered it after I replace the crankshaft position sensor. You can hear the hissing noise once the engine cover is off.

Unfortunately no, any Mercedes Benz dealership will be able to tell you using the VIN.

I took me about 2 hours, I took some extra time to make sure I didn’t break any of the harnesses. The intake area needs to be cleaned, be very careful about any debris falling into the engine. Cover all your intake ports.

Your good man it took me two hours, just to get all the wiring, harness unclipped, and all the plastic crap out of the way I’m not a pro, but I’ve been working on cars my whole life, and these Mercedes are a real chore

It was like a big plastic puzzle

It’s called a Crankcase breather vent line. Part # 276-018-23-00 it’s for the GLE M276 Bi-Turbo. Double check the part number for your vehicle.

Hi, I’m not sure. You should hook up an OBDII to see if you have any codes first.

It will most likely be some dam sensor you just gotta figure out one or replace each one!

@@got2getit204 camshaft sensor maybe? I jus changed the crankshaft .

When u changed the sensor did it have to be programed

No, increase temperature of the antifreeze opens the the thermostat, the temperature sensor sends information to the pcm (computer) and to the temperature gauge.