Видео

Do you think the 10 year warranty by Generac is worth it, in your opinion.

Looks great!!!!

Thank you - that was helpful.

Larry, I’m having trouble finding a bracket that fits the JD mower deck. The hardware included with my deck adapter is not sufficient for either of my JD tractors, zero turn and 1025R. Where did you get yours? Is there a part number for the adapter/brackets?

I've had my DR Pro 4 years now and it's a huge work and time saver each fall. Great machine. It turns our maple and oak leaves into confetti. I break it all down at the end the season to make storing it easier. The hardest part of putting it together again is stretching the enclosure enough to fit the inner frame. I've come up with self-made help tools to make that go a lot easier. My JD X354 has a bagger, and I am able to attach the DR to the bagger chute using a Fernco fitting thus avoiding the need to buy the DR deck adapter and alter it to fit the deck. If I have any complaint, it would be the OEM hose is not the highest quality. I think I got one full season out of it. I replaced it with a much better-quality hose and have had no issues since.

Are you related to BO NIX?

To remove the right side cover ONLY requires hex wrench. Do NOT remove the 10mm bolt. Checking the manual would have prevented that error.

bro the compression on your mic is distracting

I would have very serious concerns with the exhaust side directly at your gas meter.

Those battery cables should be more than long enough for you to remove the battery from the unit completely while servicing it. And Always remove the - Negative first, after tripping the breaker and pulling the fuse.

Does this have a mid pto?

Thank you sir for your help

I wonder if cheap Joe's was in the flood, it's in boone NC😮

Why are people playing this sad sad music with these videos? Arent they sad enough?? 😢😢

Thank you to all helping with the cleanup. God be with you.

Thank you for going and helping clean up the school you all did an Awesome job helping the people that were affected by Helene im so amazed by the force of what the water did so much devastation & destruction. God Bless you all.🙏🙏

8 minutes in…. Clean up ?

Praying for you all

I have a massey ferguson 253 with a front end loader. I bought the tractor used about 1 year ago. I have been looking for a paper service maunal for my tractor. Any ideas where to find one?

Hey Larry. How long did your house end up being.

Thanks! Very helpful video. I just installed mine. You never mentioned why you used oil while drilling. I found out quickly after the drill grabbed and spun my hand off it. I then remembered the oil. Worked like a charm.

The music was unnecessary. I wanted to hear the machine

You might want to mark the angle fixture to the grinder base with a sharpie marker, so you know exactly where to set it in the future. I plan on buying the same mill and sharpener when I move to my Idaho property in a few years, this content is very useful so thank you

When running, I can't stand on the side of the exhaust flow. I'm surprised how close the gas meter and regulator is. Good video, thanks for taking the time to make it.

Had to refresh my memory on this cable replacement! You know how it is when you reach your 70's.....forget how you did what and when! Thanks for the refresher!

Thank you for the informative video. It was very well done.

Thanks for the great video. Keeping it simple and fun.

OMG Brother😬😳😬. Your Generac is too close to the house and your gas meter. It’s going to burn up that gas meter during a prolonged outage during the summer. 😮

Nice video ! The 70 specs 341/2 wide great product showcase!

Also, Note: Apply dielectric grease to battery posts to prevent corrosion.

Did you remove the 7.5 amp fuse? Noticed it looked like you touched terminals to generator frame when cleaning. Believe it is recommended when servicing.

Can’t wait to see the completed project!

Awesome video!!

Good job connecting to the draw bar and not the 3ph. Can't flip over that way with the pull point lower than the axle.

Thank you

nice work thanks for sharing your work

I saw your account name on the back of a truck I typed it in new I'm here :)

Hallelujah. I am so happy for your excellent video. I am confident I have all I need to service my battery!!

Hell no. Had a recall on the bolt for propeller and shop has had mine now for 35 days, still not back.

& I like your truck

I’m right behind you right now

Great information 🎉🎉

Going to work on my Gererac in a few days. Great Video. Question: After the battery is disconnected, Do you have to re-enter any configuration in the menu?

When checking battery I always use my multi meter to check battery voltage when the terminals are disconnected. It should read 12 volts when its not being charged with the systems trickle charger. Great video thanks for sharing,

Thank you so much for this video. Our battery just died and we couldn't figure out where the battery was located. Saved us before the storms start this week.

Good Job 👍

The boards underneath your sawmill going left to right and you cut out around the feet. Does the boards have anything to do with structure?

Were these from a company called vevor?

Ate they LED?