Видео

See three of the videos now an no one says what size torx it is !!!

For Linksys router this trick will work?

It would have been much easier to just leave the cable on the RP-SMA and solder the pig tail directly onto the circuit board 🤔

Unfortunately I have the Version 14 of this router and there is only a snapshot version of OpenWRT.

I need a help as soon as possible you can reply About an experiment I have a Tenda ac5 router connected to my main ISP via PPPOE Now I bought a new router which supports OPENWRT As I think the router of TP-Link TL-WR841N V13 which has 8mib Flash and 64mib Ram, then on Tp-Link router I flash OPENWRT and setup BDIX connection (BDix Connectio Mens--- a proxy which use for high-speed internet access by a new ip Connection) Now if I connect my Tp-Link router wan port in my main router Tenda ac5 router Lan port can I access BDIX connection from Tp-Link? I Means I want to use only bdix from TP-Link router. Tenda ac5 router will have normal connection in PPPOE. I just want to use Bdix on Tp-Link. is it possible? I hope to get a reply

192.168.1.1 login page error 192.168.1.1/ is unreachable. ERR_ADDRESS_UNREACHABLE Brother I can't access this page

obrigado me ajudou muito

mine is v13.1 is it different from v13 or is it the same?

good , thank you very much. I am doing a project with ble potisioning and your video make me clear many thing.

thx bro you are the best

Thanks buddy

How much should I wait for reboot

Have vpn wireguard?

Hi, great video. Can You Tell me if it is possible to instal an external conector in a 2.4. /. 5 GHz wifi modem for fiber optic that has only internal ANTENNAS?

Nifty. Many routers nowadays have crappy antennas and are impossible to upgrade.

I believe you may of spelled insulation incorrectly... or the moderator is illiterate. 😅

Thanks bro 😅

My access point Airtight C75 is being powered by poe on lan1 interface which is being detected as Wan by openwrt, instead of deleting wan interfaces can i rename it and disable firewall, will it be the same as LAN

Thanks my friend. Because of your help I discovered that my hardware can not handle being DHCP client and transmit a signal at the same time. So I tried the "static IP" option, now it works! Thanks again, continue! :)

Thanks for the video! I was missing the firewall issue!

gracias por el video amigo

You gave a new life to my old route 😇🙏

Thanks for this tutorial. I have exact the same router and this helped me set it correctly. At the Switch field, do we need change something about the tagged and untagged settings per port? What are these settings for?

excelent

Do you have video for this model is v9?

Mine does not appear on the switch menu.

$250 makita new battery I used it only just one month and won’t take charge anymore , do we should repair it, unacceptable sorry makita this is first and last for me to buy this junk tools

I recognize that this is very old, so there may not be any response. However, I've been unable to get the first part (Blink on motherboard) to work. I believe that I have followed the procedure exactly correct, downloading the utility and driver and connecting the 51822 to the BLE400 and the STlink. The Arduino sketch verifies successfully, but, when I try to upload, it fails with an error that says the board is not connected to any port, and the port is "grayed out" with no port listed. But, I see that your port is also grayed out implying that you have no connection either. When I installed the Nordic utility, the firmware update did succeed, but, then, it says there is no device connected. I feel like I'm missing something simple, but can't tell what it is. Any help? (In case it matters, this is Windows 11.)

how to recover original

Very useful, I was able to reflash my router. Thanks for this video!

Perfect 👌

Hello, thank you for the video. Subtitle translation does not work on my device. I have a question please. Is there a user manual for the controller?

how recovery to tp link

please upload wr841 v14 openwrt upgrade.

I couldn't connect pppoe to wan..

Note from 2022 Feb. First powerup your module and check if it's advertising via BLE using nRF Connect mobile tool. If yes, the module has an application preinstalled. I bougth Nrf51822 at aliexpress, and this is my case. My first attempt to flash a simple blink sketch FAILED. During this attempt the arduino-nRF5 ERASED the preinstalled app, but couldn't go on due to 'target closed connection' or similar error. Apparently, I didn't see the module advertising after that erase. To SOLVE this issue, just move on and flash Softdevice as in video, and your new application will be flashed smoothly. Besides, I didn't use motherboard and connected wires directly to the module, and then checked the blick sketch work using pin20 and DC voltmeter

Your video was very helpful to me. Thank you

Great..Thank you very much for the clear explanation. I have made my led blink with nrfapp.. A little disappointing is the power consumption. The board takes 4.4mA☹️

Thank you for this video, was very helpful 🙂 greetings from Poland 👍👍👍

Well done. I builded my pulse welser With another card model, result is not so good. … I will build it again thanks to your video.

Thank you so much, so far I was trying without the flash soft device and I couldn't get any results. l solved it thanks to you.

do you have a video about your spot welding device? I'm very interested for it, thanks!

everything is ok, blinking, softdevice etc. but nrfconnect app can not find nrf51822 module. :(

Its not measuring first cell, its using it to power the board

Thanks a lot. This was awesome. Really awesome. You dont know what all things I tried.. HC05, HM10, AT etc etc .. And also this one is such a cheap solution for the bluetooth applications. Can you upload one more tutorial on how to connect the two NRF51822 devices and push one button at one nrf and led glow at another. That will remove the dependency on the nordic app and then one can make its own controllable device. Thanks a lot.

I think earlier ones shipped with M3 case screws. Not very optimal for plastic, but they changed them later to proper screws for plastic. It is a good, but relatively expensive case in ny opinion :)

I'd love too see more on that spot welder. Have a sub and a like

i have done do all step, but i still cant see my bluetooth. i'm not using motherboard. can u give me some help?

Very clear and concise instructions, Big Thanks! Works like a charm!!!

Amazing guide! Thank you! Used ST-LINK V2 and nRF51822 module without motherboard, and Windows 10 virtual machine - works exactly as described.