Видео

i believe this is the feathering shaft being bent, when it dives to one side like this

My XK k123 is spinning on its own axis after a 30cm drop. Any tips on what it could be and how to fix it?

Est ce que cela est compatible avec la radio xk x6? Sur iOS Car j’ai pas de pc et je débute lhelico 3d J’ai un simulateur sur mon tel avec la radio du xk 110 Le nom de la radio est xk x6 avec une prise du style jack3.5 Est ce que cela marchera t’il

Thank you it works properly and safely 👍🏻love from India❤️❤️❤️

kalau untuk ke pc,ada kabel.tambahan .apa langsung colok saja.saya menggunakan type remot yang sama??

Where download driver for SM100 cable cant recognized my PC win 10 pro and FS-i6

제꺼도 그런데 저거 어떻게 해결하나요

Does work in iOS Sistine???

Bro rf real flight simulator is not available in play store

This could be a bend shaft or else your servo gone. Check your servo bro

Can it be used on fs i6?

Adjust the pushrods of swashplate’s servos so it can lift perpendicular to the main shaft

Calibration do wrong left corner and right corner pull back 3-4 second by pass blue light is first moved after quite this is calibration. Utub you can find X6 Radio Calibration than you may know how to do.

can I connect Radiomaster TX12 just like this?

Gyro calibration may solve the problem. Holding down both sticks on your transmitter for around 3 seconds lights will flash fly your Heli in a steady hover for several seconds and land then hold down both sticks again lights will flash and turn steady on. You should be good to go. It may be difficult to get that initial hover just keep trying it because I've seen that with successive calibration attempts the Heli will become steadier in the air with each attempt at calabration. Also resetting the gyro by holding both sticks down and out to the bottom corners for a couple of seconds resets the gyro. Be sure the 3D/6G mode switch is turned on off (up position). Good luck

I have done, that is very amazing.

Hiii I need help can u help plz

Can i also do this With My iPhone?

Thank you so much. There seems to be zero information on the internet for this ESC. This was driving me nuts.

Did you use this on continous flights without cooling down ? The culprit must be the esc below the battery tray. Wl v931 also a replica of as 350 few vedios are available where owners cut holes on front canopy on the below and close it with a small wire mesh to let air in. Anyway since you are using replacement board make sure let it cool after flights.👍

Sounds like a weak lipo. Cant put out enough amps.

Thanks from Bangladesh 😍

Yeh connector kaha se le?

Whats ur contect number

You help my friend

Wowwww Very Nice

I got same problem with my XK x110. I returned it where I bought it

Please reset the gyroscope of the helicopter circuit due to misunderstanding by the system

What is the name of your transmitter

i am having the exact same problem the motor stop after a short time

Idol don

Nice vehicle, nice video Awesome Let's get along with friends with the same hobbies. 잘 지내봐요. 😁😁

Ur receiver is stick too tight on the heli, replace the sponge double tape

Try turning it on?

Calibrate evrythink

Fist thing to do is ramp up the motor right up to the point of liftoff. Then raise it just enough for the left side skid to come off the ground, you may want to put electrical tape on the right side to keep it from taking off. Adjust roll trim till it touches the left skid to the ground and settles, do not go farther as the right side of taped down will not tell you if you have gone to far. Now take the tape off, and raise the throttle till it start to take off, if it goes sideways again repeat the above, if it goes ok then you should adjust the servo wire ends to match where the head is so you can take out the trim you just put in.

The weight is more in the right side It cousing problems to chopper. maintain weight both side equally Then try 🙂

Armando😊😊😊😅😅😁😁😁😀😀

é bateria

👏👏👏👏

I think there is hair in the propellers

You have something bent. A bent mainshaft or feathering shaft causes enough vibration the gyro can't handle it. Take the head apart and roll the shafts on glass plate. If you can detect any warp at all, they must be replaced.

Calibrate gyro accelerometer,aileron trim left?

Don't need the calibration how a drone?

Waste

Give it to me 😅😅😅

Nice flying 👌 👍 👏

Ajust the servos unplug it and adjust them to the distances to the recomended for the fabric .

If you don't need that can you give it to me

Your to far right back it off to the left more should fix it