Видео

Doesn’t work with a machine that doesn’t let you touch the track with the bucket.

thanks just got a new E26 100 hours ago and had a track come off I still had help come over got it on for the most part but had to use the bucket to get it to pop back on the video was a big help thank you so much

My track just came out inside a hole will try to fix it after this video . Fingers crossed crosses!!

Thanks for the video! One of my greatest fears as a new excavator owner. I now feel I can easily get it back on by myself.

"Put the bike chain back on the sprocket." Great job! Improvise, adapt and overcome!

You did a great job with the video. Nice clear instructions. Very well explained. Don't pay attention to the idiot Where is his basement professor professional video. I'm an Equipment owner operator and you did a great job.

As a one man show You did excellent..👍😊 I would seriously think about the final drive sprocket teeth are showing excessive wear.

Owe you a beer, saved me a phone call to the boss man

The same way you put the track back on with a large excavator. Just watch how Tony Beets does it. Bucket to the side and raise the the drive side off the ground.

ruclips.net/video/zeHDVo7FiLI/видео.htmlsi=vHY-7K1dL6I2wnEc

Not exactly what I searched for on RUclips, but pretty pretty cool technique. Too bad your moron in the shop didn’t watch and learn, nevertheless subscribe

Do you know these size fields are for how many gallons a day or for building of how many people ?

Only strait forward vid. My track came off alone. Same logic. My rippa 2023 didn’t have enough power to do this in the woods. I nursed it back 1/4 mile to try to do this again in a safe environment. I have no tools.

Always good to make a 7 min video when it could just be 2 at most. Not sure why we needed to know what job you were working on etc.

Nice one mate. Got the track back on without having to tell the boss 👍👍

Ur undercarriage is rough, the drive sprocket is like knife blades….

It's a good technique but remember guys it's one off or you are somewhere in the desert you do that, doing this can cause the rubber track to rip because of stretch force

What about if the track goes out to the other side

Never to old to learn something. Good job. Thanks from. Sc

Thank you for sharing, you got my sub.

Massive job. Great work.

How much does blasting for tank cost?

I had to do the same by myself and the only thing I did differently was when I got the track sitting as close to the underside rollers I lowered the entire machine onto the track and drove backwards while turning the machine and track against the front main roller. It makes a hell of a bang so now I do the same but I remove the grease tensioner before tracking against the track. Takes me now 10 minutes to get it on before adjusting the track.

Time for a tractor with a snowblower lol

What's going on here

Thank You Im off to retrack my Kabota 33! Great value!

This looks like the equivalent of “hold my beer and watch this” snow plowing.

That's a 300.00 push all day long....😁👍

Are you still doing this road? Did you find a better solution? That is a very difficult road for light duty pickups especially with wet snow. Snow tracks might give you enough traction to plow in 4 low but they are expensive and have to be taken off to drive over 35mph. If you put some 35's with chains on one of your trucks and add enough weight you might be able to drive to the top first and plow down which is really how it should be done. Plowing uphill is very hard on equipment.

Are these guys new?? Good grief

Chain all 4.

Thanks for posting the video, a lot of guys on here are arm chair warriors and don’t have balls to put there own videos up. Keep the videos coming.

Nice job ! But how that truck jumped been so tight ?

My bucket couldn’t reach but a 2x6 worked to bridge the gap

Been working excavators 40 years. Usually just man handle and pry bar and another person on controls. Oh and a lot of cursing. When by yourself, as I was other day, and track came of G50 JD used this method and took a whopping 4 minutes. Pissed I never did it ages ago . Makes perfect sense and just never thought of it- to much dust in the brain I guess . So good one ☝️ CJ with Mountain-Scapes

Just used this video to fix my Yanmar ViO 17s track. Thank you so much.

Tried today. But busted the track. Ordered metal ones.

Well as a Veteran Snow plow guy. You guys Suck! Blame it on learning curve or whatever you want. This guy has NO common sense… that and it’s a dodge 🤮🤮 $money pit! Buy a Ford next time…

Subscriber #360 👍🏻 I’ll remember this if it ever happens to my new KX080-delivered 6 was ago!

Most people today would call it quits for the day. You just showed American ingenuity to get the job done! This may seem simple but in a small way it shows we are competing globally. Good job Jesse!

I wish that was my commute

❤️ p̲r̲o̲m̲o̲s̲m̲

Works because you have big bucket!! 👍😂

How many hours on the Kubota kx 040

Get a set of real snow tires and learn how to shave off layers of snow

That driveway needs a bobcat

Man that is one gnarly driveway!!! It appears that it's all uphill. Too bad there wasn't someone that was able to come downhill and break trail. You guys work well together for sure.....Stay safe....

Get a Tundra.

Why doesn't he put the blade all the way down?

1:20; What an idiot!