Видео

ID 220MM or 8.7 inch, OD 251MM or 9.9 inch

Mine stopped working as well, I replaced it with a new one, it worked again. The next morning I found that it wasn't working again.

Happen to have Link to the ring gear you ordered?

Thank you! 10383321 turn signal relay #

Thanks you I tried everything know left turn signal only Wright turn signal I ordered same part number your post hope it work

Thanks for the video, I have the same problem on a Kohler Courage Pro 25hp, ring gear is cracked and missing 2 teeth! They use crappy, cheap Chinese steel, why isn't the ring gear welded on? Stupid idiot engineers!

Thank you for this eye opening video as I’m in nz and the cost of a whole flywheel is 1200 dollars can’t buy ring gear here but got one off eBay this morning I used a punch to get the ring gear off 😊. Vince

How did you get the old one off.

Hello Stephen thank you for the video. i have a similar issue with a JD x300 that i've had for 12 years. It's fine when cold but intermittently will not engage when hot, although if i turn the engine off and back on again, it will engage? Would you consider this an air gap issue? Many thanks

Thanks, dude! Your video saved me some money.

I so prefer levers and pulleys. Even with my drive systems.

If your voltage regulator is not puting out proper voltage it will do samething or weak battery check these first!!!!!!!

Thanks for the video because I'm having this problem now with my 2005 Chevy Tahoe

DO U KNO OFF HAND WHAT THE TOOTH COUNT IS ON RING GEAR AND STARTER? TOOTH COUNT IS?... THANKS MUCH IN ADVANCE. { MURF }

Great video! Thank you.

Husband just replaced mine🎉 Thank u very much your video was very helpful ❤

On 2004 Yukon there is a ground wire behind driver side rear tire that goes from the chassis to up near the gas filler cap area. If it is broke rear blinkers wont work along with other strange electrical problems.

Thank u

I have a 2016 gmc sierra sle i have this code U0077 i have aftermarket light everything was working fine for the past 2 years with the LED lights yesterday i have a Right Rear Turn Failure could this fix my issues i try cleaning the ground when the truck is on everything is perfect except turning right and my break

Thank you for your simple and helpful video just got mine done on my 2005 avalanche ✅

Thank you Stephen, I am very grateful for the effort you have made to make this video, this helping people like me. I no longer have to wait for my mower to cool down! You fixed my mower! Thanks again.

Thank you so much!

Great video ! That really stinks that Kohler wont sell just the ring gear. Good thing for Vogel MFG, but I think they are out of stock as I type this. Hope they can manufacture some more ! 👨‍🔧

The installation instructions which came with my replacement clutch were very specific to **not** use an impact wrench to tighten the bolt. Use a torque wrench. In the case of my clutch, torque the bolt to 55 ft-lbs. Yours may vary (check your service manual.)

Awesome video

Same problem: I rode my tractor up a ramp and reached under and just tried the 1/4 turn on all 3 nuts and is working like a charm. Took 10 minutes and did not have to take anything apart - praise the Lord! Thanks for the video!

Glad I found your video. Seen it after ordering the flywheel for $442.00. Called Vogel Manufacturing to confirm theirs was the right one. Canceled the flywheel order! While I was counting the teeth I discovered 2 more spots with missing teeth! Apparently the original ring gear was made from some kind of crappy material..Comforting to know the next one is good quality. THANK YOU FROM SASKATCHEWAN, CANADA.!

Is it working OK for you sill? I may order one but wonder about reliability. My mower is down till I fix this! Thank you for posting this video, it really helped! I did order one.

If there was ever a recall this would be the one.

Very good video you’re a great teacher, thank you!

Thank you ,

Did you just lift up the front end of your tractor and set it on its rear? If so, did you strap it so it does not fall forward on you? Question: Is it possible to reach and turn it a 1/4 turn on each bolt without taking it apart? Meaning you could reach the bolts without removing the deck. May be a stupid question, but I have multiple level disc issues and this type of thing can be real painful.

Exactly what my Cub Cadet is doing and still does. Took to shop and they said it was the air gap and it worked for 2 mowings afterward and now it quits working after 30 minutes (when hot). Then let it sit for 15 minutes and it works again.

Great vid; I'm having the same issue.

Great tutorial and a real time saver

Thanks for this!

Left turn signal not working, been chasing this problem , this , is a confirmed fix!!! Thank you

The right turn signal in my 2003 Suburban reliably works but the left turn signal only works sometimes. Sometimes I need to turn the left signal on and off 3 times before they work, sometimes it takes more than that. Also sometimes I need to turn the steering wheel (at a stop at an intersection) a good bit to the left before they will work and stay flashing.

>>>GMC/CHEVY DESIGN ENGINEERS ARE TOTALLY ""FUCKING NUTS""

Man!! I just replaced mines. What a job when you don't have proper tools 😅😅😅

Good to know. Thank you.

Good to know. Thanks for the video.

Excellent video. Just bought a used crafstman dyt4000 first time I used it today blades worked for about 10 minutes and shut off. After watching, tightened all three nuts one turn and did the whole lawn with no problems. Blades cycle on and off hot! Thank you very much!

Did tip the lawnmower over to fix the issue and take the part off

Yes nice video. What is it about the heat factor that pointed to a PTO adjustment? The heat did what exactly?

I had same problem I sprayed with brake cleaner and has worked ever since

Good video

Just changed the ignition switch on my 2001 Chevy 2500HD Silverado and now my turn signals work when they feel like it. (started one week after) Thanks for the excellent video, in spite of your camera.

I accidentally was messing with the ground of the signal light plug with a metal picking tool while the turn signal was on and forgot to turn it off before all of that. Now it won't blink or flash. Did I static shocked and burnt the turn signal relay?

What if pto disengages it self after about 15 minutes of use and then will work again when it cools down? When the PTO does disengage it self there is no power too it. Ohms test of PTO reads 3.6