Видео

Just did my driveway with this screed chairs..16yrds 87 ft long 16 wide..it was good for cutting the job in sections and before doing this big job..I only done 4.. 5x8 slabs..these chairs help you a lot and make the job fast..

Killer MTN OPS shirt!

LOL what skool did this guy go to? He should ask for a refund. Rebar does NOT go on the slab centerline (aka neutral axis).....it must be in the bottom 1/3 of the slab to reinforce the tension stress that exists in the bottom of the slab. Putting rebar on the neutral axis just keeps it together after it cracks in 50 places 😆

I recently purchased your screed chairs. other concrete guys say not to use a power vibe screed on the forms. I was told to set the level with wet mud and float the power vibe screed on the mud. you are screeding on the forms directly here, so its ok to do like this?

longer rebar or grade plate? that is the question of 2024.

I'm in Boise watching this after being ripped off from pre-paying a guy to do a concrete work. the forms are setup, I purchased a vevor power screed, bullfloat, fresno, broom and edgers. lets go do it. sometimes to get the job done right, or at all- you must do it yourself.

I used the viber screed, i think i need 2 , 1 on each side tbh

Have you guys experienced cracking at the joints in all honesty? Ever?

Looks like it works pretty damn good 💯🔥🔥

Man , bro I wish my pops heard of these...he was using wooden stakes and 2x4..😊

Waste of rebar being 0n the ground.

That’s something I’d like to try for bigger pour especially when the slope has to change

Отлино

Bonito trabajo

Im not austrailian😂😂😂

Retired concrete contractor and on my big pours I would set up overheads witch were basically a L bracket with a I hole that was tapped for a set screw . All I had to do was pull a string line from form to form set at grade and slide a 2x4 that was above the finished grade of the concrete and pull the steel staks the were attached to as we screeded . I wish I would have bought a roller screed . Two back surgeries was what I paid for being set in my ways . Your 100% right form to form is yhe right way to strike the mud off

your labor cost to grade perfect and saving concrete is basically a wash at the end of the day vs. when you just quick grade and pour a hair deep ! I have done both and the cost is pretty freaking close to the same when you compare ! Just my 2 cents.

Тупорылые арматура на земле валяется

I can’t believe you guys pour concrete for a living. No rubber boots no come alongs , your roller screed is bouncing. Hope you have a great Darby man. 😂

That rebar is doing nothing just sitting on the ground. Isn't it supposed to be held up at least an inch or two?

Never seen nothing like this....wow!!!!

👍🏾

That's a lot of work for what 3 or 4 stakes and a high screed could do. But I admire your young guy pluck.

I think the reason the roller screeds are not used as much anymore because when I started in concrete in 1984 they were only made for commercial work. They were so big you needed heavy machinery to move them around. But I would use one now because I see they are built smaller and it doesn’t require a 10 hp engine.

Union wages always help get guys in the trades and an incentive to stay in the trades.

The laborers need concrete rakes

We used to use vibrating screeds where we would run steel cables back to steel stakes and then the ratchet cranks to pull the screed along. This looks a lot easier

just use a regular knife 4 or 6"....

I understand that every country may do things slightly different but that looked like it was being done the hardest way possible. That screed rail setup took so much extra work with very little benefit. Just my thoughts

I wana try this shit on a patio

Fabricate bar chairs in my workshop is a break from everything else. Not paying for such simple tech, and as you say it has been around near a hundred years....

I do like the idea that anyone can screed

Dont use lasers... the oldest simplest tool around and argualbly the best tool is a string line. I set grade steaks

Where did this guy come up w the term cow patty😂😂😂😂😂

Hand rodding would be faster, though a little harder on the back and I never liked how the roller would fling cream back on the finished surface. If this is an advertisement it's funny that you have a Bunyan handle and tube ends on the roller :)

Does it get expensive leaving the chair in the concrete?

Where can purchase a screed rail?

Where can i purchase a flat bar?

Can you use a vibrating screed with your screed chairs? have you ever? any problems

running the power screed backwards !! Dummies. No clue what they are doing !!

The way you absolutely sold kicking down the first one vs making sure you stepped on top of the other was comedy gold lol if you’re going to do this kind of stuff you have to at least make sure your not so noticeable when applying intent

What if there’s a high point right at the end

those aren't going to stay vertical

Forms are probably set to grade but they double check elevation with laser. They probably had a bad experience in the past. Somebody probably moved the forms and elevation was off in the past and now they double check with laser

People don't like innovation. I've worked on high rise construction for over a decade and been in dozens and dozens of pours and nobody likes to be told how to pour easier or faster. They'd rather kill their guys and "tough it out". Btw, no roller screed in high rise construction in Los Angeles. I saw them years ago. Nothing new, but people are hard headed and stuck in their ways

Where is the rebar? Is this a demonstration?

Where’s the tape

👏👏👏👏

Naw perro thats not screeding

Take this video. All wrong. Why teach wrong