- Видео 1
- Просмотров 42 405
Mermaid Manufacturing
Добавлен 16 авг 2016
Mermaid Marine Air began operation in 1983, providing quality marine air conditioning products to thousands of satisfied customers, both nationally and internationally. Our very first location was in North Fort Myers, Florida.
We are fortunate enough, as a company, to have an extremely low turn-over rate. The majority of our entire Mermaid Staff (Marine & Medical) have been here for 10+ years, on average. Our guys work very hard and are extremely knowledgeable. Your A/C, Dehumidifier and Medi-Kool Products are hand-made each and every time. We stand-by our product.
Our customer base stretches across the United States, Canada, Europe, Asian, Africa, South America, Australia, New Zealand and the Caribbean.
We are always in the research and development phase for new products, so be sure to check back and see what's new. We are open to our customers feedback and suggestions for products you currently need.
We are fortunate enough, as a company, to have an extremely low turn-over rate. The majority of our entire Mermaid Staff (Marine & Medical) have been here for 10+ years, on average. Our guys work very hard and are extremely knowledgeable. Your A/C, Dehumidifier and Medi-Kool Products are hand-made each and every time. We stand-by our product.
Our customer base stretches across the United States, Canada, Europe, Asian, Africa, South America, Australia, New Zealand and the Caribbean.
We are always in the research and development phase for new products, so be sure to check back and see what's new. We are open to our customers feedback and suggestions for products you currently need.
How to change a filter dryer
Mermaid Manufacturing explains how to change the filter dryer on a Mermaid Medi-Kool Climate Controlled Cabinet.
Просмотров: 42 424
WHERES YOU NITROGEN WHEN BRAZING
👍🇮🇳🕉️🙏
As a school-trained licensed and certified HVAC technician. This is working the easy lazy way, which sooner or later catches up to you. Referring to the refrigerant as "Freon" gave me the hives. No deburring? Lazy. The bending is so badly made it kinked the tube, which produces flow turbulence. Not protecting the filter from the brazing heat? Nice way to possibly damaging it. Having nitrogen and planning on using it, but not flowing it during the brazing... oh boy. Carbonization in the inside. That filter might need replacement soon again. But if you only didn't refer to the gas as "freon"....
Hack, using wire strippers to cut the cap tube, and drier.
My dryer filter is very cold any ideas ?
Very helpful. Thank you.
This is r600a its a flammable please don't braze it, this guy will get you killed.
Nice job my fellow technician
Brazing job is poor
How about dryer on any reefer unit. Thank you
Your solder is bubbling up, too hot frame.
How do you understand you got problem in the filter dryer?
95% of the time that’s the clog if you have blockage. There are ways to test. You are going to replace that anyway during a service where you are going into a sealed system.
Induction brazing better than this
Shop mentality . That was the lazy way of doing that.
What kind of solder material are you using to solder?
I have a problem. When I try to move a refrigerator from one place to another on the backside the oil inside the compressor return back to the filter and damages it. Is that video help me to avoid that?. Any other solutions could help to prevent the oil from going out to the filter and damage it like a one-way valve or other ideas. Please suggest me solutions. Thank you.
Just wondering : why does the filter need to be changed when replacing a compressor? Is it something that can be done in stages? (change filter on day 1 and compressor on day 2?). Thanks
filter dryer is there for catching moisture, chemicals and copper oxides created during brazing process (because they don't use dry nitrogen at time of brazing). After years of work when you change compressor that filter is almost clogged out and needs to be replaced. If you don't replace it, it may work few years OR only few weeks before gets clogged. When you install new compressor you create even more oxides that have to be filtered. Both compressor and filter should be brazed at the same time so the system is sealed quickly to prevent moisture getting in. New compressors and filters comes with sealed both ends so compressor oils (which very often are hygroscopic) and filter's desiccants are protected until installation time.
@@vihayster thank you! Much appreciated :)
Thank you for showing to cut the new dryer ends nobody else showed that part.
No nitrogen purge while brazing. What a mess.That cap tube will plug up.😨😳
yeah...seems to be new normal. I haven't seen any videos with nitro in use during brazing refrigerator components. I think everybody assume that filter will catch everything, lol
@@vihayster I haven’t seen any either. strange
You kinked the pipe and then didnt even talk about pulling a vacuum lol.
That pipe is kinked