Видео

Yes, we recommend buying the PU sealer to waterproof it in that case. Look at this kit: www.epodex.com/en/product/microcement-for-floors-and-stairs/

Hello, That depends on the initial state of the floor. If the floor is every uneven and textured, sanding might be required, as the epoxy is onyl 1.5mm thick, it might not mask off profound unevenness.

@@epodex-uk3877 is there any reason a matte finish on top would be a bad idea? Would it collect more dirt/bacteria/moisture? What type of matte coat would you recommend to make it look kind of like natural stone

@@WhatALovelyDisaster We'd recommend our Polyurethane matt top coat for a matt finish: www.epodex.com/en/product/2k-polyurethane-resin-in-gloss-and-matt-finishes-all-colours/

Hello, Some tiles are not sandable, you can continue with the use of our Pre-Cleaner, and then 2 coats minimum of the Tile Paint.

Hallo, Neem hierover contact op met ons ondersteuningsteam: +31 10 310 0203 klantenservice@epodex.com

Does using a torch alter the pattern much if you're going for a multi-coloured effect?

Hello, Well you cannot use a torch over cured epoxy resin. You can use the torch while the epoxy is still wet to remove them.

Hello, Yes this is waterproof and steam proof when the Polyurethane Sealer is applied. See here: www.epodex.com/en/product/1k-concrete-effect-for-concrete-design/

@@epodex-uk3877 tks I'll check that out 👍

Hello, You can allow the left over residue to harden, it then pops right out :)

@@epodex-uk3877 really? Excellent. Thank you. Good advice.

Hello Bryce, Can you send photos of your floor to support@epodex.com for further assistance? TEAM EPODEX

Hello Lynn, With our 2K Polyurethane Resin, you must apply it very thinly, in a crisscross motion. This process eliminates lap lines or roller marks. The product is also dilutable with water to avoid an orange peel texture.

Hello, Yes, it does, it's designed for these purposes :) The EPODEX Tile Grout Pen is a special acrylic-based paint for colouring and refreshing tile grout lines. See here: www.epodex.com/en/product/epodex-white-tile-grout-pen/ Team EPODEX

Hello, Yes we offer Microcement for walls: www.epodex.com/en/product/microcement-for-walls-doors-and-furniture/ Make sure your order the correct primer as well: www.epodex.com/en/microcement-individual-products-components/ For further assistance email support@epodex.com. Team EPODEX

Hello, You can test our Laminating & Constructing epoxy system: www.epodex.com/en/product/epoxy-resin-for-laminating-construction/ For more assistance please email us at support@epodex.com :) Team EPODEX

Hello, Normally yes, but it also depends what paint was used on the concrete previously? Email us at support@epodex.com :) Team EPODEX

Hello, You can use our Tile Paint directly: www.epodex.com/en/paints/tile-paint/ The gloss level for 1K is satin & for 2K satin matt. Do you mean can you make it more glossy? EPODEX

Hello, You can use our Polyurethane Sealer found here: www.epodex.com/en/product/microcement-for-floors-and-stairs/ EPODEX

Thanks :)

Bună ziua, PU lucios: 10:2 în greutate (de exemplu: 1 kg A + 0,2 kg B); PU mat: 10:1 în greutate (de exemplu: 1 kg A + 0,1 kg B). Sper că vă ajută :) EPODEX

Hello David, Yes our MATT version has the highest scratch resistance :) EPODEX

@@epodex-uk3877 Thanks a lot :)

Hello, Our products are BUBBLE FREE so we do not recommend using a pressure pot nor can we advise what pressure to use as we dont test our products with a pressure pot. Team EPODEX

Hello, We recommend stirring for 3 minutes, then transfer the mixture to a clean mixing jug and stir again for another 3 minutes :)

Hello, No its not :) If you decide to sand only use DRY sandpaper. EPODE

Hello, We do not recommend spraying our epoxy resin. What kind of project do you want to do? EPODEX

Our Tile Paint 2K has a satin matt gloss level :)

Hello, We recommend the Pro System. www.epodex.com/en/product/pro-system/ The epoxy resin PRO system is ideal for coating surfaces and making jewellery and small objects. It can be poured up to 2 cm deep per layer. The Resin A-component and hardener B-component are included in each set, as well as the desired colour dye or pigments. Instructions for use can be found on this product page. 24 hours at 20°C to harden and 7 days for full chemical curing to occur. You can use a demoulding spray if needed but epoxy never bonds to silicone moulds :) Team EPODEX

Hello, It wouldnt be easy no :( Removing paint is never easy. We offer the 1K acrylic based paint and the 2K epoxy resin based paint. The 1K would be easier but still a hard and messy job. EPODEX

Hi :) Our products are chemical products but once cured and hardened they are not toxic and do not pose a threat to one’s health. Our products are remarkably odourless during processing, but we always recommend wearing a mask, protective clothing, and gloves (nitrile). Goggles can also be to protect one’s eyes. When sanding and griding surfaces please wear a respirator mask to avoid inhaling dust. Always work in a ventilated room meaning that the doors to the room are open to provide adequate air flow but do not open the windows as humidity can affect your work. Team EPODEX UK

Hello Jasmine, This is called a Dirty Pour Technique. Heres how it done: If you wish to create a dirty pour you must first create a barrier (dam) around the edges with our strong, durable masking tape. Press the tape around the entire project. The tape should stick up at least a half-inch. 🎨 Pro Tip: One continuous piece of tape may be difficult to achieve but aim for as few seams as possible. Don’t wait too long before removing the tape. If the resin completely hardens, it will be difficult to remove. For the least hassle, it is best to remove the tape no more than 16 to 12 hours after pouring. Gelling times can be found on our system comparison sheet. You want the resin to be set, but still flexible so that the tape pulls off easily allowing the epoxy to flow down the edges in a slow movement. Upon removing the tape, you will notice some spots that will need to be treated with a paintbrush to ensure full coverage. Make sure you dip the paintbrush in the epoxy mixture before using it. Start using the paintbrush in a horizontal motion, spreading the epoxy over the edges. Do not worry about messing your design up if you have worked with various colours as the epoxy will still flow downwards bringing the design you have created over the edges. Only work on the face of the edges, not the top. Once you have painted the edges with a paintbrush take a stir stick and run it along the bottom of the edges to scrape the bottom drips off. You will need to do this periodically for an hour or two. For a final topcoat of epoxy, you can sand at a higher grit as the epoxy layer will then remove the scratches from sanding. You can round sand the bottom edges as well if needed to give the finishing touches to your edges. Hope this helps :) Contact me for more assistance at support@epodex.com. Team EPODEX

Hi Gordon, Ofcourse :) Do you have the moulds already? How thick do you wish to pour the epoxy resin? Team EPODEX

Hello, We recommend our Tile Paint 2K: www.epodex.com/en/product/tile-paint-2k-all-colours/ It is an epoxy resin based paint :) Contact us via email at support@epodex.com for direct assistance and design tips and tricks.

Thanks

Hello, We are only selling epoxy resin in the USA at this time but will expand our product range soon :) Team EPODEX

Hello, The rose or any real flower must be 100% dry before it can be casted into epoxy resin :) TEAM EPODEX

Hello, Thanks for your interest! Do you want to coat a surface with colour or without? TEAM EPODEX

Hello, Thanks for your interest! What are the measurements of your project? Length, Width, and Depth? I can see what we can offer you :) TEAM EPODEX

@@epodex-uk3877 Hmmm… I’d say no larger than 1 1/2 (one and a half) inches, length and width. Probably pretty thin, but thick enough to fit a small cut piece of paper, maybe an inch or so depth. Small but big enough to use for a charm to wear on a necklace or something similar? Would that work?