Видео

You said to put "grease" around the gasket of the oil filter... I'd use clean oil from one of the new bottles rather than grease.

I just use the end of a popsicle stick. Good job on your video. Thank you.

👍

Just read on Amazon the wheel goes flat after a few months. Is there a fix for that ?

Thank you so much. I tried replacing my motorcycle battery and was frustrated after an hour. RUclipsd it, had extra rubber hose and was installed flawlessly in 5 mins. Thank you sir, not all heroes wear capes.

What a nice content

These are NOT 90 degree locking hinges. While they open and lock at 90 degrees, when you closed them the will not lock in the closed position. The supplier said "just raise the hinge on a block". I tried adding a 1/2" block and that did not make it lock. I then went to a 1" block and that didn't work either. Even after adding a block height of 1.5", the hinge would not lock down. It appears that the hinge may have to get closed to a 115 degrees or more before it will lock in the closed position. That being the case I would have to add upwards of 2.5" of block to raise the hinge enough to make it fold and lock. In turn, it your looking to get a flat leg fold, that does NOT work. When shown both the video and raise block pic, the response from the supplier was "Just send them back". TOTAL WASTE OF TIME WOR THESE HINGES.

These are NOT 90 degree locking hinges. While they open and lock at 90 degrees, when you closed them the will not lock in the closed position. The supplier said "just raise the hinge on a block". I tried adding a 1/2" block and that did not make it lock. I then went to a 1" block and that didn't work either. Even after adding a block height of 1.5", the hinge would not lock down. It appears that the hinge may have to get closed to a 115 degrees or more before it will lock in the closed position. That being the case I would have to add upwards of 2.5" of block to raise the hinge enough to make it fold and lock. In turn, it your looking to get a flat leg fold, that does NOT work. When shown both the video and raise block pic, the response from the supplier was "Just send them back". TOTAL WASTE OF TIME WOR THESE HINGES.

What happens when im laying pipe and the. Little bitty screws come out

Thank you for your nice video

how do you stop the wheel from swivelling when you are closing or opening , my wheel swivels. tot he side and blocks the opening or closimng motion

I just used aquarium tubing ! 👌

The bottom of your gate needs to be roughly 8in off the ground for the wheel to be able to clear 360deg rotation, because the mounting bracket off-set is only enough to flush up with the wheel in 1 of its 2 perpendicular positions. It's a good 2in of additional off-set needed to clear the other side. This is the issue that I am working towards some sort of solution for on 2 - 7ft. long black iron swing gates. I may have to actually cot it clear, then weld a little boxed in are on the other side of the gate. I don't like the idea of a block or something like that because it is a brand-new gate in the front of the house. (RV Access)

thank you. now I see why I couldn't figure out how to install mine - I have a wood bedrame and a different wood headboard. They line up with no gap at the corner as you show here. What kind of bracket might work? the manufacturer of the bed frame does not recommend and currently I have the headboard pushed up against the wall but would really like to secure it directly to the bed frame. Thank you

😮🤔😮😱👍

Thank you

I followed the steps as described having removed an old sleeve that broke down. The new sleeve seemed to hammer in place just fine, and the castor stem clicked in giving the feel that it went beyond the narrowing end of the sleeve as needed. But a week later the same leg had a note on the chair seat, next to again, its castor leg, stating that it fell out. When I removed the new stem I had gently hammered in place, its narrowed end had become expanded such that the castor fell out. How did the castor click in place beyond the narrowing sleeve, and then that narrowed section expand? Is it possible that I perhaps should have bored a hole a smidge deeper to be on the safe side? Or maybe you can provide me a link to a better quality sleeve, although mine bought at a hardware store sure look the same as what you used in your video.

Thank you. I am a 79 & female. Your video aided in my independence. No handyperson needed, just the help of my daughter. Bless you.

Does it open all the way with that wheel not swiveling

Double wire hose clamps are for currigated hose and the like.. lol this video was a waste

The table should extend out the side of the leg for easier maneuvering of leg

So do these toilet Seat Bumpers can be used on all seats., where do you buy them.

Good ideas. How about using a soft tape measure, similar to the ones a tailor uses?

Thank you for clear, straightforward info. Slow enough to follow, but never dragging. And you answered questions as they popped to mind. Excellent info and delivery! Thank you!

Please demonstrate in malayalam

man im not a scientist

So well explained: simple and clear! Thanks.

India gujrat surat City

I have metal driveway gate est measurement over 15 feet long been sagging . Would this work? Not much of an expert at perfectionist. Would be easy for avg guy. I can try send picture

What do you recommend for rough and uneven grass/dirt?

Wow! Who would have quessed it was that easy!

great, how do i remove it? please!!!

Bad Amazon reviews

The Amazon reviews for this product are subpar.

Where can I buy it

Thanks! I have one alligator clip is loose and won’t connect. By you demonstrating the release mechanism I noticed my spring is damage. I just need to tighten it up so alligator claw can be tight again or buy new replacement. But your video helped me find a solution so thank you

Why didn't I think of that?. Great tutorial.

Good explanation. Comments help too

To the point. I like it

I just ordered this set but you guys forgot the screws in the package

00708 folding table leg hinges how much

How much

Gentlemen, this is Industrial Caster Wheel itself. So the wheel must be Roller Bearing, not ball beadings.

Very helpful. And whonsaid we'd never need geometry? Now i teach PE and math😅

Does it matter if I use replacement steel nut and bolt instead of the type that came with the new battery?

Is there any specific reference that I can get for using this protection if the post height is 6ft or shorter?

This was the best video. I wanted to replace casters on an old antique dresser. I didn't know the names of things, so I wasn't sure what to look up what I needed. Thanks!

Thank you so much 😊

Thank you so much for this. ❤ I needed it!