Видео

Hello dear

@@magentastar8839 i required some support for crestron knx

I required some support for knx and crestron.

How May I help you , Where are you based , Just small brief so I can understand .

magentastar.techservices@gmail.com

@@AmitUP-tp2kw Will try to put in coming days

@@AmitUP-tp2kw Yes correct dear , I believe it’s need experience Royal Enfield Mistry ( Mechanic), good knowledge on old models, For me I face starting issues. But it’s always give good mileage.

Diesel how it react with Iron tank , I have no idea , Petrol I have seen , if we keep for year in tank , it’s colour changes and gives problem in starting, Recomended not to use. But as you suggested , May be little amount of engine oil and shake the motorcycle, so that the oiling is properly done inside of the tank. , ( keep the fuel tap close , do not forget to remove the engine oil , by removing via fuel pipe ) I believe it’s individual choose, To do this as extra level. Thank you for your suggestions Regards

Dear Rahul, If you have some friends in New Delhi, That’s would be great, As he can visit , Karol Bagh market Newdelhi, and find the required spare part. As it’s difficult to get old model parts. Normally nobody replies, if you send email to them, or WhatsApp. Mostly need to visit these shops and select required items. Good luck

Hello Dear Rahul, Namaste, I don't have much idea about the Pre-owned RE Motorcycles pricing, But i guess approx Rs. 35,000/- to Rs.40,000/- may cost. also depend upon the Condition , as you mention as OK its means condition is OK, also depend on Person - the Seller of the RE motorcycle. Good luck

Thank you dear

Yes, I do agree with you, that’s why I have put info on description, Will try to put another video soon with clear audio and explanation

Thank you for lovely comment

Dear unfortunately I don’t have right answer, Mostly its combination of few things , spark current or carbonator issues, Also Try to keep the ideal running little higher . I know this issue in my Thunderbird also, I have also plan to look into during my next visit to Village early next year.

Yes correct, If you don’t see this varying voltage, it means there is no output from RS585 port / connector while send or receive signals.

@@magentastar8839 thanks for reply, on one card I see the voltage floating, one other the voltage is fixed. Can I try if there is a problem in input of the IC? First to try to change the 485 ics

@@antonio.stefanelli Ref. To IC level ( repair) I have not done, therefore no idea. But if you maintain the power 12 V DC normally operating voltage, and input conditions are maintained. If IC is ok , it should give outputs, I think you have no option but to try and change the new IC Good luck

At one point in the video we get a reading of 0.004V. This is way lower then the stated 0.8V? Why is that?

Where we have to measure this , master or slave end?

Hi agree with you , As audio is short clip, it’s not perfect,could you please check in description I have put the detailed info as text Good luck

@@magentastar8839 Thank you.

I guess , if you purchase the complete set of indicators , that would be easy to fix , as it’s fix by inbuilt bolts with frame (mudguard) once you open the old indicators , same way follow the step in reverse and should be ok to fix , need to take extra care of the wires to fix or connect same way . At present my Thunderbird is at village, I should have checked and updated you but at present not possible. Go ahead purchase new and try to fix yourself - Good luck

Dear Purchased cap is not as original- little difficulty in fixing ओरिजिनल न होने के कारण , लगाने में परेशानी हुई.

@@magentastar8839 kya aap apni bike sale karna chahte hai...?

@@honeykumarvats.g227 हनी जी, अभी तो कोई विचार नहीं हैं , किक स्टार्ट होने के कारण थोड़ा परेशानी होती है. फिर भीं अभी कोई बेचने का विचार नहीं है. मैसेज के लिये धनवाद.

@@magentastar8839 OK, Mujhe aapki bike bahot achchhi lagi. Waise aap kaha se belong karte hai..?

@@honeykumarvats.g227 धन्यवाद बनारस / गाज़ीपुर के हम रहने वाले हैं. मैसेज के लिए धन्यवाद.

Hi Francis, Thank you for your liking this video, However what’s your plan ref to purchase of old model RE

आप को असुविधा हुई . आप क्षमा करें अपना ख़याल रखें

Thank you

Thank you dear

Thank you dear

Great point! Yes , its a plus point , Should be adding this step into description / text on video, I believe 25/ 50ml should be OK, as putting more , could be a starting problem once you want to start , Because engine oil will remain into bore , and will fill the spark-plug making hard to start, or need to remove the extra engine oil via spark plug hole , also need to clean spark plug point many times ,till the motorcycle can start ( over filling of oil into spark plug point ) What do you think a small amount approx 25ml should OK - I believe Thank you for your suggestions

@@magentastar8839 you're absolutely right. The manual says 50 ml. I just checked. 25 to 30 ml should be sufficient if storing for a short period like 3 to 4 months. I apologise for the wrong information. I am editing my original comment to reflect the right info.

Thank you for updating the info, will try to add this info on the video as text info in coming days - thank you again

Hi Ref to your info You need to put the codes -RS232 of the projector. Values in Serial IO module, And put IP address of the projector . Or connect serial RS232 cable / wires with your crestron processor Com1 or another as per your selection - Copy the Com1-tx &rx to the desired port. and connect to com port projector. Try if not working swapping 2/3 pin wires Or I believe the model supports crestron Fallow the video in the list BENQ Projector LU 950 control via Room view This sure will help you as it’s without codes. At your projector Crestron control menu Put IO IP ID same in your SW program, and put controller IP to communicate. Good luck

Hi , I believe if you see the IO model Crestron KNX IO v3.3 On the gateway type:- Double click There are two option CGEIBIP[1d] And CIKNX[2d] Select 2nd one And use Gateway ID:2d Good luck

Hi may I get some support for knx crestron integration.

Hi Ninja, Unfortunately, I don’t have any idea, I believe, if you try with some of the part supplier’s, they can arrange. As it’s easy to make now days. It’s matter of get printing. Good luck

Hi Prakash, Yes, if you remove one of the terminals wire, that’s would be Great, As this old model, Thunderbird, Works without battery also. That’s why I missed to mention. Yes it’s good practice to remove the battery 🔋 connection carefully and apply electrical tape or wrap with plastic- the wire end. Thank you

@@magentastar8839 👏👏🖒

Thank you dear

Thank you & you are welcome

@@magentastar8839 Do have idea if I want the projector power ON when call com from Cisco Sx80?

@@eng_kalil787 hi If you have BENQ projector And if it’s Crestron room view ready There is one video already showing procedures in one of my channels video Or if you could specify what you facing Contol issue Sure we can try to help out

@@magentastar8839 I have EPSON projector, Sx80 cisco, clearone DSP, RMC3 controller, I need when calling come to Sx80 controller send to projector to runing.

@@eng_kalil787 Hi Khalil , I believe other functions are working Ok Below is my recommendations:- Crestron Partner Module at Application Market Cisco Model: SX80 Device Type: Video Conference Crestron Module - PDF help file Digital joint -Page No 4 Incoming Call_<Answer/Reject> D Pulse to answer or reject the incoming call. Make this link with Projector on digital Joint no in SW , by adding OR signal Also if you want to Reject and You selected - Call Reject Two functions should happen 1. Call rejected ( Disconnected) 2. You should have one small Sub page popups -Asking as Do you want to switch off Projector If Yes - Projector goes to OFF (link the Yes -Digital Joint with Projector OFF) If No - Nothing happens and projector keeps running (On) ----------------------------------------------------------------------------------------- You can try below also if you want only to run ( ON the Projector) FEEDBACK: Page 7 Copy this digital joint - Projector ON signal to the below joint in your SW There_Is_An_Incoming_Call - D - High to indicate that there is an incoming call. Good luck

Hi Pradeep, I purchased from abroad Online , by Desertcart, this unit came from INDIA. Approx within 12days. (1st from Amazon, but my order was cancelled because of the supplier failed to meet Amazon requirements, got full refund.) No local supply here .

Thank you Karl , for the suggestions, at present no plans for P R O M O S M , as i am putting these video for myself to keep as records and help to some one if its useful to them.

Dear Kumar, It’s very unfortunate that , you couldn’t make it done , There are several reasons, May be some time Internet is slow and shake-hand between your Laptop & Aadhar service is longer and it’s time out . Any how try again if it’s start working, next time it’s would be helpful. Further, After 20th January we can discuss on zoom and may be some helpful to make it work.

Dear Kumar, मैंने जो विडीओ में दिखाया है . यह लैप्टॉप ऐप्लिकेशन से है. और यह एक वर्किंग सलूशन है. मेरी जानकारी सिर्फ़ यह विडीओ के बारे में ही है. अगर आपको कुछ हेल्प मिलती है तो मुझे बहुत प्रसन्नता होगी. जय हिंद

I believe, you are using on phone, try to delete the application, and do reinstalling application on your android phone .

Hi Mohammed, I believe you do not need USB driver to work on Crestron Dali , you need crestron Dali configuration software to configure vis USB

I believe that , DIN-Dali 2 required a Crestron controller, its not a universal device to use as directly , but yes , Crestron Controllers (RMC3) can communicate with other automation , like KNX but required KNX gateway,

Thank you