![Briteworks International Inc.](/img/default-banner.jpg)
- Видео 9
- Просмотров 45 537
Briteworks International Inc.
Добавлен 5 ноя 2015
Instructional training videos regarding techniques and procedures for properly using Briteworks metal maintenance products.
Interior & Exterior Stainless Kitchen Cleaning
Most Important Video Regarding Basic Stainless Steel Cleaning For Interior & Exterior Kitchens, Surfaces That Are Not Heavily Rusted But Just Scuzzy Or Layered With Film From Other Products That Were Applied Previously Before The Briteworks System.
Просмотров: 399
Видео
Aluminum Polishing Instructional
Просмотров 4098 лет назад
This Is Where Most Products Cannot Be Used On Aluminum Because Of Them Are Formulated With Acid And Other Contaminants That Will Turn The Aluminun Black And Accelerate Tarnishing And Oxidation. Briteworks Polish Is Chemically Pure, Even So That You Can Clear Coat After Polishing And It Won't Turn Dark Between The Metal And Clear Coat.
Pre-soaking Brass Platters / Trays
Просмотров 1128 лет назад
More Examples Of Pre-soaking Very Tarnished Pieces Without Having To Polish Them Right From The Start By Hand, Letting The Polish Do The Hard Work Before Hand.
Pre-soaking Tarnishable Metals Brass / Copper
Просмотров 1968 лет назад
Briteworks Instructional On How To Pre-soak Extremely Tarnished Metals So The Product Can Do All The Initial Work, So You Won't Have To. This Is What Makes Briteworks Metal Polish Superior To All The Other Products On The Market.
Badly Rusted / Water Stained Outdoor Stainless Steel
Просмотров 5178 лет назад
A "Real Time" Length Video Instructional On How To Camouflage, Or Minimize The Rusted Away Inferior Soft Steel Particles And Water Stains In A Low Grade Stainless Steel Grill Cabinet Door.
Badly Rusted & Pitted Outdoor Stainless Steel
Просмотров 43 тыс.8 лет назад
Stainless Steel Instructional, Cleaning Extremely Weathered Exterior Grill Cabinet Base Panel That Is A Low Grade Stainless That Will Pit And Rust Because Of It's Inferior Grade . This Video Is To Show How To Camouflage And Restore The Best Kind Of Finish Once The Soft Steel Particles Rust Away Due To Neglect And Elements Exposed Over Many Years.
Condensed stainless cleaning
Просмотров 2208 лет назад
Briteworks Brief Instructional Video On The Techniques Of Cleaning And Preserving All Satin Stainless Steel Items Especially Kitchen Appliances And Outside Grills / Patio Kitchens.
What products are you using and where can we purchase them?
Rusted stainless ?? Uhh... must be very poor quality ?
Any stainless steel can corrode. Depending on the grade, it can be more resistant to corrosion. The particular corrosive will also greatly affect how susceptible the stainless is to corrosion.
How do I get rid of the streaks?
Hello Johann, If there are streaks, that means there still is residue from the cleaning process that is still present and draging across the substrait. You can continue to rotate your rag until there is no dark residue on the wiping sections of the cloth.
Hello Johann, here was the same issue from a person a year ago. Hello EL, If you have successfully cleaned the substrate thoroughly with the polish then you have to thoroughly remove the polish residue off the metal until nothing of any color is coming off onto the rag/cloth. If you have streaking, it is because the metal still has residue from the polishing beforehand. To clean it properly, you fold up a 2-3 wide in X 10 in long cloth/rag strip into several folds, dip it into a small container of Preservative to submerge the rag/cloth, ring it out and then go up & down or Side to side ( whichever the satin finish grain/pattern is going) and continue to take full length wiping and folding over the rag/cloth, and repeat the wiping and rotating of the rag/cloth until the rag/cloth is as clean & white as when first submerged into the container of Preservative. You have to take full-length wipes so you don't have any start and stop areas because you are pushing/moving the residue down and off the panel. Once you have everything super clean and the preservative dries, you can take a microfiber cloth and do a light buffing if any streaks still appear. It is the dirt/residue that is causing the streaking. Once you start buffing with the microfiber cloth and have any dark residue coming off the dry Preserved panel, then you know it wasn't clean enough and hence the streaking. I hope that will be a clear and effective answer to solve your question. Kind Regards, Nathan 1 Reply E L E L 1 year ago @Briteworks International Inc. hi Nathan….through some trial and error I was able to figure out it was user error and it wasn’t clean enough before applying the preservative. What you just described is what I did and it worked wonders on my Coyote BBQ. My neighbor is going to be buying some for his Lion BBQ as well. Thank you! Reply Briteworks International Inc. Briteworks International Inc. 1 year ago @E L Sounds great El! I am glad to hear about fine minds being put to work and not giving up on an initial negative outcome, excellent work, and congratulations on critical thinking measures that you are blessed with having!
Where do I get everything?
Would this be safe to use on a semi gloss powder coat that’s on aluminum?
Used a automobile paint fine grit rubbing compound like 3M perfect it 3.
How do you apply the preserve to not allow “stripes” to form? Polish works great but the preserve stripe makes it look horrible
Hello EL, If you have successfully cleaned the substrate thoroughly with the polish then you have to thoroughly remove the polish residue off the metal until nothing of any color is coming off onto the rag/cloth. If you have streaking, it is because the metal still has residue from the polishing beforehand. To clean it properly, you fold up a 2-3 wide in X 10 in long cloth/rag strip into several folds, dip it into a small container of Preservative to submerge the rag/cloth, ring it out and then go up & down or Side to side ( whichever the satin finish grain/pattern is going) and continue to take full length wiping and folding over the rag/cloth, and repeat the wiping and rotating of the rag/cloth until the rag/cloth is as clean & white as when first submerged into the container of Preservative. You have to take full-length wipes so you don't have any start and stop areas because you are pushing/moving the residue down and off the panel. Once you have everything super clean and the preservative dries, you can take a microfiber cloth and do a light buffing if any streaks still appear. It is the dirt/residue that is causing the streaking. Once you start buffing with the microfiber cloth and have any dark residue coming off the dry Preserved panel, then you know it wasn't clean enough and hence the streaking. I hope that will be a clear and effective answer to solve your question. Kind Regards, Nathan
@@briteworksinternationalinc1177 hi Nathan….through some trial and error I was able to figure out it was user error and it wasn’t clean enough before applying the preservative. What you just described is what I did and it worked wonders on my Coyote BBQ. My neighbor is going to be buying some for his Lion BBQ as well. Thank you!
@@el9107 Sounds great El! I am glad to hear about fine minds being put to work and not giving up on an initial negative outcome, excellent work, and congratulations on critical thinking measures that you are blessed with having!
How do you get the preserve to not “stripe” when applying it and letting it dry?
Briteworks International Inc. 2 minutes ago Hello EL, If you have successfully cleaned the substrate thoroughly with the polish then you have to thoroughly remove the polish residue off the metal until nothing of any color is coming off onto the rag/cloth. If you have streaking, it is because the metal still has residue from the polishing beforehand. To clean it properly, you fold up a 2-3 wide in X 10 in long cloth/rag strip into several folds, dip it into a small container of Preservative to submerge the rag/cloth, ring it out and then go up & down or Side to side ( whichever the satin finish grain/pattern is going) and continue to take full length wiping and folding over the rag/cloth, and repeat the wiping and rotating of the rag/cloth until the rag/cloth is as clean & white as when first submerged into the container of Preservative. You have to take full-length wipes so you don't have any start and stop areas because you are pushing/moving the residue down and off the panel. Once you have everything super clean and the preservative dries, you can take a microfiber cloth and do a light buffing if any streaks still appear. It is the dirt/residue that is causing the streaking. Once you start buffing with the microfiber cloth and have any dark residue coming off the dry Preserved panel, then you know it wasn't clean enough and hence the streaking. I hope that will be a clear and effective answer to solve your question. Kind Regards, Nathan
@@briteworksinternationalinc1177 perfect thank you! Great product….literally removed high heat sear marks and baked on grease that nothing else could remove.
@@el9107 That's why the Cruise Line and Outdoor kitchen-BBQ Grill industries have used it for 2 decades, if Briteworks products don't work, nothing short of professional metal machining will! It was great to make your acquaintance and have a splendid day EL!
Stainless steal outdoors is so stupid
Bruh. Rub the metal with the cream. Video done. No need for using every big word you can think of. 20 second video
maybe put a cloth down to stop that panel sliding about :P
I have a Lynx grill with highly polished areas. Will your product work without damage to highly polished areas.
Yes, it would, but you have to use a very soft cotton or microfiber cloth and I would recommend soaking the surface with the polish for 5-10 minutes, just don't let it dry! If it drys, re-wet it and then very gently polish in one direction do not put heavy pressure, light, light, light and then check your finish from there. Mirrored Stainless will scratch so proceed with extreme care!
Thanks for a reply. There are these little mirrored strips of stainless around the edges of the hood. I am trying to figure how to do the SS that has grain running either parallel or perpendicular into the polished edge without messing up the mirrored edge But, I just finished the two lower doors that were badly stained. They look amazing now. This is an amazing product. My grill is 12 years old and sits about 50' from the salt marsh.
Where would I find the video about the "re-graining" you mentioned?
Hello Kenneth, I did mention that there would be one, but I also realized this is a skill set that the average viewer may fail at acquiring the same results as I would be demonstrating. You are the first person who has wanted to attempt this procedure so you can go onto the website: www.briteworksinc.com/?page=contact and send me an email with your contact number, or I will send you mine and discuss it in detail and see if you are feeling comfortable in your ability to execute this technique. It isn't as hard as you may think but does require some preparation, concentration, and some hand/eye coordination. It can be achieved also with a guide like a straight edge to keep the grain perfectly straight. Thank you for your interest and have a splendid day! Kind Regards, Nathan Nass
Kenneth Vaughan Hello Kenneth, I was going to do that one, and then had a change of mind. Please send me a message on the website and I will get in touch with you on the technic. Thank you! Kind Regards, Nathan