- Видео 8
- Просмотров 14 203
BMF Fishing Adventures
Добавлен 21 сен 2011
Contender 25T running hard and cruising - uncut footage
This video shows how well the Contender 25T can handle the chop. Running out I optimized trim to achieve higher speeds while skipping the waves and active throttle play. Towards the end around the 6 minute mark in the video you’ll see me bury the tabs heavier with less speed to optimize the ride for comfortable cruising without any throttle play. I’d call these a moderately spaced 3-4’ all day.
Просмотров: 5 206
Видео
Caught and released Mahi, Marlin & Cuda out of Fort Lauderdale FL with the kids
Просмотров 227Год назад
Catch and released Mahi, Marlin & Cuda out of Fort Lauderdale FL with the kids on the Contender 25T
Catching a few Swordfish in Fort Lauderdale FL on the Contender 39st
Просмотров 155Год назад
Knocked down 3 swords fishing out of Fort Lauderdale FL on the Contender 39st with the Tree Shaka
My 4 year old catching Mahi while fishing out of Fort Lauderdale FL
Просмотров 45Год назад
My 4 year old son rolling out with me on the 25T out of Fort Lauderdale FL with him catching and reeling up multiple Mahi 💪
Picking up a Wahoo & Tuna while fishing in Fort Lauderdale FL
Просмотров 132Год назад
Picked up a wahoo & tuna on the planers while fishing in Fort Lauderdale on the Contender 25T
Where you using the tabs?
Just for level
Great display of the 30st's offshore ability. Working those tabs !
Andrew Tate mode!
😂
Hell yeah! Looks like a good day and the kiddos had a blast 🤙🏽🎣
What's top speed with the 200's ?
For the money I buy a Porsche 911 Turbo , used, and a single diesel straight inboard fishing, used too, boat with some seats, used, that I can sling chum, blood and beer all over without crying. Autopilot it where I'm going without needing a post workout shake and a nap afterwards. Impressive though. Good luck and enjoy it.
what was your speed most the time?
Mid 30s head, 40 to mid 40 following
Amazing video, great job.
Glad you liked it!
My sled has the twin200 hpdi. In the ocean I typically never go past 42-4500 rpm and have her trimmed down. No wedges. 2009 hull. Give her a lil tab but not much. Obviously if it’s rough I tab her but the more I tab it the more she barks. That’s why I tend to run it at a lower rpm so if she barks it doesn’t over rev.
Can you go into more details about your setup? Motors, rpm,speed and tab? I just picked up a 25t and I’m still learning to run it. Very impressed on how you her running.
Rpm and speed is always the absolute maximum I can do in given seas without slamming too often. Only scaled down to who I have on the boat.
When are you gonna trim it properly
Description spells out exactly what I was doing. What you consider proper is last couple min backing off and digging tabs more.
You have no idea how to trim a boat
Man you have that one dialed in for sure .I swear the faster you go in ours the better it rides.
I’d like to see a rear view of the engines. I know those things have to be barking hard.
Only a few barks on that ride. Tried keeping the ass glued down a bit on that run.
Looks like it’s eating it up 👍
@@DevanMoree-ev7efsure is
The beast master. I share the same feeling when going out to open sea in Puerto Rico
It’s 1/2 the fun lol
Ran a 25t for 450 hours one year. Note here- If you want to slow a bit faster because you are about to catch a big wave, use dual throttle and pull one motor back, it creates drag and slows you faster than pulling both
What where the sea that day
Every bit of 3-4. Video doesn’t really show it.
Got some power!
Throwing your cigar over the side shows poor form mate
Good thing it’s made of leaves and is biodegradable.
Nice!
Boat did well