Видео

Hi, friends. As usual, i needed a "special" solution for my workshop. This time, it was up to the windows. Windows in this design are hard to come by in my country. So i had to make my own.. It is the longest video which i have every made for YT. So feel free, to skip parts of the show to your own will. Follow me on lari_fari_youtube '#woodenwindows #windowmaking

..just a little side project...

Hello my fellows.. A lot of bla, bla on this one.. ;) Here is the outcome of a little tinker project, wich i was working on in the last weeks. It is a single axis solar tracker circuit. Pure analog. No microcontroller is needed. You can find the full circuit diagram on my pinterest profile: www.pinterest.de/LariFariRUclips/ Or on Patreon. com: patreon.com/LariFari/ Or follow me on instagram: in...

Hi, friends and welcome to my new, but still not finished workshop. In this video you see me restoring an old bench vise, which i got for free. This is not a big or complex project but a very important one. Or should i say...i needed the damn thing.... :D Feel free to become a patreon under : patreon.com/ LariFari Or follow me on Instagram: lari_fari_youtube #viserestoration #vise...

Hallo friends. In this video i want to show you the progress at the construction site and share some thoughts and plans for the future with you... Feel free to become a Patreon under : patreon.com / LariFari Or visit me on instagram: instagram.com / Lari_Fari_RUclips

..Making the Motor unit of the new Ventilation system. The Fan which i used for this build is a odenary 50 cm 230 Volt cooling fan with 180 watts max. (purchased on ebay) By the way..this is the last build project made in my "old" workshop. I am about to move and build a new workshop / studio. If you want to support my channel, you can do so on: patreon.com/ LariFari Or follow me on instagram: ...

Hi, Friends. It happend again. I am about to move to another place, with all my stuff. 33 tons of tools, materials, event equipment had to be moved and stored at the new location. Next step will be to build the workshop, toilet and shower room for my guests.. If you want to support this project, feel free to become a Patreon under patreon.com/LariFari You can also find me on Instagram instgram....

makers, freaks and friends.. (and a cat)

Hi, Friends. In this video i did some experimenting on cleaning aluminium with electrolysis. I used citric acid as electrolyte. ratio: 1 Table spoon for 12 Liters of Water. The DC power sourse was a Welding inverter. But you can use any other DC power source, available. #electrolysis #aluniniumcleaning #electrolysiscleaning If you want to support me out here in the shop, feel free, to becom a P...

Hi, Friends.. Here is a little Project which was on my list for a long time. It is a simple but robust DC dummy load for load testing up to 50 Volts and 20 Amps... I will post the circuit diagram to my pinterst and to my patreon profile.. Feel free, to become a Patreon and support me out here in the shop. I will also post this video there, so you can watch it without adds.. Thanks for your supp...

Hi, Friends.. I had some questions on how i program my Attiny Microcontrollers which i used in some of my projects.. So here is how i built my "Arduino as ISP" Programmer. Here is the pinout for the Arduino Nano: Pin 7 control LED "programming" ( 220 ohm resistor) Pin 8 control LED "error" ( 220 ohm resistor) Pin 9 control LED "heartbeat" ( 220 ohm resistor) Pin 10 RESET of target µ controller ...

Hi, friends... Here is a little woodworking project.... It is a collapsible work table made out of spruce and OSB.. Feel free to copy this design..like..share..subscribe..or leave me a comment. If you want to support me and my projects out here in the shop, you can become a patreon under: www.patreon.com/LariFari #workbench #folding worktable #worktable

A little september walkthrough... Prepairing for a party. ;) If you want to support me and my projects out here in the shop, you can become a patreon under: www.patreon.com/LariFari

homemade table saw part 4 (cross cut fence, elecronics, extention, test cuts)

Homemade table saw pt 3 (rip fence, cross cut sled, dust hood...)

Shop update june

Homemade table saw Part 2 (machinebase, tilt system, table top...)

homemade table saw part 1 (motor lift)

homemade panelsaw in action

metal turning with pimped wood lathe

super simple DC softstart circuit

Whats up in the shop..

DC high side switch (for Arduino)

DIY snowplow for the forklift

shop update september 21

simple soft start circuit DIY

panel saw automation circuit overvew

mowing the hedge