Видео

I will look it up and post it for you.

That is a great question depending on the make and model. You can find them online, local hvac company or appliance store.

They can be picked up at any local appliance repair shop or online. Just look up your model number and make sure it is the correct part number.

Unfortunately no. A washer drum has 2 parts to it the inner drum (where the clothes go) and outer drum. There are ways to separate the 2 drums just depending on the brand and model.

Most top load washers do not have lint filters that can be serviced. To clean, place the washer in "clean" cycle. Front load washers have an access panel usually bottom front. Thanks Anthony for watching and asking.

Thank you for the positive feedback.

Clean filters on any HVAC system will allow the proper air flow and circulation needed for the system to operate properly.

Glad you think so! Thanks for watching Salem Kares.

Hey Lee Hart thanks for watching. I am a Maintenance Supervisor for a multifamily company.

Sounds like an issue with the main control board

Thanks for replying so what do I do. Do I get the whole kit with harness or would replacing the lid lock part and where is the sensor for that? The sensor is what sends the signal is it not.

Thanks Eric. You are correct, you can do this on when they are not damaged. This is the way I was taught by the GE service repair.

You are correct in this post. It is the basic cleaning. Full service clean is remove the cover plates drop the unit down carefully remove the condensation pan. Clean the blower wheel, coil, condensation pan and pump, check the drain lines and vac them. Never got around to making a video that detailed due to it being a rental and limited time.

This is my Buisnes in Toronto over 25 years in Buisnes

Awesome Akbar

Next replace that comes up I will try make it better. What would you like to know more on?

No problem it is an honor to hear that.

Easier yes, but I wanted to show the whole replacement. Someone might need to replace the wire harness as well as the lid lock. For educational purposes.

Thank you very much.

Yes, you can replace just the lid lock but for educational purposes wanted to show the full replacement as you get it all in the kit.

Note: we heard clicking right after the smoke/steam burst into the air, up toward the security camera

It sounds as if the heat pump is going into defrost and it is normal. If you have an electric heat pump system. The heat pump pulls heat from the outside and as the air temperature drops the unit ices up and needs to go in Defrost to clear the ice. This cycle lasts average 5-10 min.

It’s a lid lock switch if you call your local appliance store and give them the model they can find your lid lock kit.

We you can run a washer not connected for service to see if it runs or diagnose the mechanics but alway proceed with due regard and caution. The water just is just for the clothes to move and wash.

Yes thank you

This is a great question and a very common issue. First thing you wanna do is wet vac the end of the line outside to try to clear it first. There are hidden screws holding the case cover on. With the case removed this will expose the inside drain line. Always try the outside first.

TJ Marco You’re very welcome glad to help.

Depends if it a magnetic lock or a physical lock.

@@braxtonboysmaintenance2644 mine is physical, looks like the same model as the one in your vid. any tips?

The paper that came with the new type switch had something about the switch not releasing and to make sure it was retracted when installing. Jus sayin'

Installed new lid lock. In my washer lid only locks during rinse and spin cycle.

Jose, some units do only lock during these cycles and others will lock the entire cycle time.

Lexie, Thanks for watching, there could be other issues that would need to be troubleshooting to determine the issue or issues.

I am not to familiar with that specific issue. Is it a side by side, freezer drawer or top mount?

Thanks for your reply. It’s a whirlpool french door bottom freezer. The compressor comes on fine, no clicks near compressor, evaporator fan comes on intermittently, the copper coil thingy the thermostat is attached to gets cold icy but it doesn’t spread to the rest of the coil fins. Sometimes the freezer fan is spinning (evaporator fan) and other times it doesn’t come on but when it is in it just circulates warm air.

As not being able to physically diagnose it listed are possible reasons for the issue. I would recommend having a certified whirlpool technician run diagnose your cause. Could be several issues the common is bad door/gasket seal, defrost timer, less common is temp control board, dirty coils or bad compressor. Best of luck and please let me know! Thanks

Before you do any work I would use the manufacture warranty.

Also make sure you give it time to cool down, settings are appropriately set and the obvious making sure it has power (gfci not tripped)

It is called that it’s a basic video for filter cleaning not a full strip down and cleaning.

God and Family so glad to hear we could help.

Thanks for watching glad to help.

Thanks for the comment glad to help.

When you say the timer switch wasn't advancing what do you mean by that? My machine will not agitate and I am at my wits on the cause.

@@jodibrewer5005 the timer knob on the front of the dashboard has to advance from fill to wash, rinse and spin..if your timer switch..which is under the timer knob..is faulted..your timer knob wont advace...most times that switch kneeds to be replaced.

Thank you John

I have a video of opening the cage.

@@braxtonboysmaintenance2644 got a link?

Where!?​@@braxtonboysmaintenance2644